Cisco NCS 4206 Manuale di istruzioni

Installing the Cisco NCS 4206

This chapter describes how to install the Cisco NCS 4206 and includes the following sections:

•Prerequisites, on page 1

•Installing the Chassis in a Rack, on page 1

•Installing the Chassis Ground Connection, on page 10

•Installing the Fan Tray, on page 12

•RSP Installation, on page 16

•Interface Module Installation, on page 20

•Installing the Power Supply, on page 22

•Installing the AC power Supply, on page 28

•Power Cable Bracket (A9XX-PWR-CBL-MGMT), on page 31

•Top Cable Management Bracket (A9XX-TOP-CBL-MGMT), on page 33

•Connecting the Cisco NCS 4206 to the Network, on page 35

Prerequisites

Before installing the Cisco NCS 4206, it is important to prepare for the installation by:

• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP)

• Unpacking and inspecting the Cisco NCS 4206

• Gathering the tools and test equipment required to properly install the Cisco NCS 4206

For more instructions on how to prepare for the installation of the Cisco NCS 4206, see Preparing for

Installation.

Installing the Chassis in a Rack

The following sections describe how to install the Cisco NCS 4206 in a rack.

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To

install the brackets on the front of the chassis, perform these steps:

Installing the Cisco NCS 4206

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the chassis.

Figure 1: Attaching Mounting Brackets for a 19-inch Rack (A903-RCKMNT-19IN3)

Figure 2: Attaching Mounting Brackets for a 23-inch EIA Rack

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended maximum torque

is 28 in.-lb (3.16 N-m).

Step 4 Repeat Step 2 and Step 3 for the other bracket.

Installing the Cisco NCS 4206

Installing the Chassis Brackets

Installing the Chassis in the Rack

The procedures in this section apply to both horizontal and vertical mounting of the in a rack.

To install the chassis in the equipment rack, perform these steps:

Step 1 Position the chassis in the rack as follows:

• If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting

posts.

• If the rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.

Step 2 Guide the chassis carefully into the plenum assembly. See the figure below.

Figure 3: Installing the Chassis on a 19-inch Rack (A903-RCKMNT-19IN3)

Installing the Cisco NCS 4206

Installing the Chassis in the Rack

Figure 4: Installing the Chassis on the Plenum in Rack

Securing screws to chassis onto rack3Plenum1

—Cable guides on chassis2

Step 3 Position the door onto the chassis and slide it into the rack. Secure the screws with a torque of n.-lb (N-m). See the figure

below.

Figure 5: Installing Door onto Chassis in Rack

Installing the Cisco NCS 4206

Installing the Chassis in the Rack

Securing door to the chassis onto rack3Chassis in plenum1

—Door2

Step 4 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.

Do not use interface module and power supply ejector handles to lift the chassis; using the handles to lift the

chassis can deform or damage the handles.

Caution

Figure 6: Installing the Chassis in a 23-inch EIA Rack

Step 5 Install the 8 or 12 (4 or 6 per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the bracket and into

the threaded holes in the equipment rack posts.

Step 6 Use a tape measure and level to verify that the chassis is installed straight and level.

Installing the Chassis with Plenum in Rack

Step 1 Position the air baffle and the side plate to the plenum. See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 7: Securing the Air Baffle Tray

Plenum base3Air baffle1

Secure screw to Plenum base4Side plate2

Step 2 Secure the air baffle and the side plate using a maximum torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 8: Securing the Side Plate

——Securing side plate to plenum base1

Step 3 Repeat Step-1 and Step-2 to complete the plenum assembly on the other side of the plenum base.

Step 4 Position the air filter (A903-F2B-AIR-F) assembly on the plenum deflector. Secure the front cover using a recommended

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 9: Air Filter

The filter is applicable when fan A903-FAN-H is used.

Note

Step 5 Using a crimping tool (as specified by the ground lug manufacturer), crimp the ground lug to the ground wire and connect

the other end of the ground wire to a suitable grounding point at your site. See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 10: Attaching the Ground Lug and Wire Assembly

Dual ground screws2Dual-hole ground adapter and dual-hole lug1

Step 6 Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb (1.3 N-m).

See figure below.

Installing the Chassis in the Air Plenum

Ensure that the chassis is not installed in the air plenum while mounting it on the rack.

Note

For instructions on mounting the plenum on the rack:

Step 1 Position the chassis so that the rear of the chassis is at the front of the plenum.

Step 2 Slide the chassis into the plenum so that the front of the chassis is in flush with the mounting rails and brackets. See the

figure below.

Installing the Cisco NCS 4206

Installing the Chassis in the Air Plenum

Figure 11: Cisco NCS 4206 Chassis with Plenum

Installing the Chassis Ground Connection

Before you connect the power or turn on the power to the Cisco NCS 4206, you must provide an adequate

chassis ground (earth) connection to your chassis.

This section describes how to ground the Cisco NCS 4206 chassis on a rack. The chassis provides two locations

for attaching a 2-hole grounding lug according to the rack-mounting brackets you use to install the chassis.

The Cisco NCS 4206 supports the following rack-mounting types:

• EIA 23-inch rack—Attach the grounding lug to the rack, as shown in the figure below

Installing the Cisco NCS 4206

Installing the Chassis Ground Connection

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco Physical Access 1125 Appliance Manuale utente

Cisco

Cisco Edge Concentrator MGX 8220 Manuale di riferimento

Cisco

Cisco Linksys Business Series Network Storage System... Manuale utente

Cisco

Cisco BR1400 Series Guida di riferimento rapido

Cisco

Cisco Nexus 93180LC-EX Manuale utente

Cisco

Cisco ONS 15454 SDH Manuale

Cisco

Cisco UCS X10c Istruzioni di installazione e manutenzione

Cisco

Cisco Nexus 93600CD-GX Manuale

Cisco

Cisco 2431 - IAD Router Manuale utente

Cisco

Cisco Firepower 9300 Guida alla manutenzione e all'assistenza

Cisco

Cisco VPN 3002 Hardware Client Manager Manuale utente

Cisco

Cisco ISA 3000 Guida rapida

Cisco

Cisco LightStream 1010 Manuale utente

Cisco

Cisco TelePresence Manuale di servizio

Cisco

Cisco Firepower 1010 Manuale utente

Cisco

Cisco NCS 1004 Manuale di installazione

Cisco

Cisco MGX 8260 Guida rapida

Cisco

Cisco SCE 2000 4/8xFE Manuale utente

Cisco

Cisco Firepower 4100 Series Manuale utente

Cisco

Cisco o UCS X440p Istruzioni di installazione e manutenzione

Cisco

Cisco CVPN3015-NR - VPN Concentrator 3015 Manuale utente

Cisco

Cisco CATALYST 6000 Manuale di installazione e funzionamento

Cisco

Cisco Content Engine 510 Manuale utente

Cisco

Cisco Aironet 1000 Series Manuale

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente