Cisco 12406 series Manuale utente
Corporate Headquarters:
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco 12006 and Cisco 12406 Router
Unpacking and Repacking
Instructions
This document contains instructions for unpacking and repackaging the
Cisco 12006 and Cisco 12406 routers. After you unpack the system, refer to the
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide for
more information.
This document includes the following topics:
•Before Unpacking the Router, page 2
•Tools and Equipment, page 3
•Unpacking the Router, page 4
•Repacking the Router, page 9
•Regulatory, Compliance, and Safety Information, page 10
•Obtaining Documentation, page 10
•Documentation Feedback, page 12
•Obtaining Technical Assistance, page 12
•Obtaining Additional Publications and Information, page 14
Before Unpacking the Router
2
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions 78-16104-02
Before Unpacking the Router
Figure 1 shows the Cisco 12006 or Cisco 12406 router on its shipping pallet. A
fully configured system can weigh as much as 205 pounds (94 kg), not counting
the additional weight of the pallet and packaging materials. Before unpacking the
system, you should carefully plan the site location of the router and the method
you will use to move it into position to install it in a rack.
Note Save all packing material and hardware (bolts, screws, brackets, and so on) after
unpacking the router. You can use them to repackage the router for shipping if
necessary.
Figure 1 Cisco 12006 or Cisco 12406 Router Secured to Pallet
50835
3
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions
78-16104-02
Tools and Equipment
Tools and Equipment
You need the following items and tools:
•3/16-inch flat-blade screwdriver
•1/4-inch flat-blade screwdriver
•9/16-inch (14-mm) wrench
•10-mm wrench (open-end or socket)
•Wire cutters
•Pliers
Unpacking the Router
4
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions 78-16104-02
Unpacking the Router
This section explains how to unpack the router from the shipping pallet. Figure 2
shows the packing material and accessory kit container.
Figure 2 Unpacking the Router—Enhanced Model)
1Pallet base 4Plastic bag
2Front door (enhanced model only) 5Accessory kit tray
3Hold-down brackets with bolts 6Outer shipping container
SLOT-0
GIGABITROUTE PROCESSOR
SLOT-1
COLL
LINKTX
RX
RJ-45
MII
RESET
AUX
EJECT
CONSOLE
CISCO 12000
SERIES
GIGABITSWITCH ROUTER
101113
1
2
4
5
3
6
5
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions
78-16104-02
Unpacking the Router
Step 1 Use wire cutters to cut the plastic bands that secure the router to the pallet.
Step 2 Remove the tape that seals the shipping container and open the top of the box.
Step 3 Lift out the accessory kit and set it aside (see Figure 2).
Step 4 Remove the shipping container, the plastic bag, and all of the packing materials
and set them aside.
Unpacking the Router
6
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions 78-16104-02
Step 5 Remove the bolts and screws that secure the two front anchor clips and side angle
brackets to the pallet (Figure 3).
If you are installing the enhanced version of the 12404 Internet router, go to
Step 6. For all other models, go to Step 8.
Figure 3 Removing the Router from the Shipping Pallet—Enhanced Model)
SLOT-0
GIGABIT ROUTEPROCESSOR
SLOT-1
COLL
LINK TX
RX
RJ-45
MII
RESET
AUX
EJECT
CONSOLE
CISCO 12000
SERIES
GIGABITSWITCH ROUTER
57679
7
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions
78-16104-02
Unpacking the Router
Step 6 Cut the plastic tie-wrapand remove it from the upper lefthinge bracket (Figure 4).
Note The plastic tie-wrap secures the front door to the chassis during shipment.
Figure 4 Removing the Tie-Wrap and Label
149690
REMOVE
TIE WRAP
Unpacking the Router
8
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions 78-16104-02
Step 7 Open the front door and remove the labels (labeled REMOVE) that protect the
rubber bumpers during shipment (Figure 5).
Close the front door.
Figure 5 Removing the Rubber Bumper Shipping Label
Step 8 Your Cisco router is ready for installation. For installation instructions, see the
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide (see
Obtaining Documentation, page 10).
REMOVE
1
49691
9
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions
78-16104-02
Repacking the Router
Repacking the Router
This section describes how to repack your Cisco router into the shipping
container. This procedure assumes you have the pallet, packing material, and
hardware you saved when the chassis was unpacked.
Note If the original packing kit—consisting of the pallet base, hold-down brackets,
bolts, screws, plastic bag cover, packing material, and shipping cartons—was lost
or damaged, you can order another kit (Product Number GSR6-PKG=)
Step 1 Place the router on a Cisco 12006/12406 shipping pallet.
Step 2 Secure the side and rear brackets to the pallet using the bolts and screws you saved
when the chassis was unpacked (see Figure 3).
Step 3 Tighten all of the captive screws on the power entry modules, power distribution
unit, and line cards so that they are secure.
Step 4 Refer to Figure 2 and:
a. Place the plastic bag cover over the router.
b. Place the accessory kit on top of the router.
c. Place the cardboard shipping container over the accessory kit and router.
Note If the master shipper tape closure was removed, replace it before you
secure the bands to your package.
Step 5 Secure the cardboard shipping container to the pallet using straps similar to the
ones used to ship the router to you.
Your router is ready for shipment.
Regulatory, Compliance, and Safety Information
10
Cisco 12006 and Cisco 12406 Router Unpacking and Repacking Instructions 78-16104-02
Transporting the Router
The shipping package for the router is engineered to reduce the potential of
product damage during shipment. To minimize potential damage to the product,
transport the router in its Cisco specified packaging. Failure to do so may result
in damage to the router or degradation of its performance. Do not remove the
router from its shipping container until you are ready to install it. The router
should always be transported or stored in an upright position. Keep the router in
the shipping container until you have determined an installation site.
Regulatory, Compliance, and Safety Information
The complete list of translated safety warnings and agency approvals is available
in the Regulatory Compliance and Safety Information for Cisco 12000 Series
Internet Routers publication (Document Number 78-4347-xx).
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco
also provides several ways to obtain technical assistance and other technical
resources. These sections explain how to obtain technical information from
Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/techsupport
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Altri manuali per 12406 series
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Cisco Router di rete
Cisco
Cisco CGR2010 Guida rapida
Cisco
Cisco Router Cisco 7206 VXR Manuale utente
Cisco
Cisco ASR 5000 Series Manuale utente
Cisco
Cisco 836 Manuale
Cisco
Cisco NCS 6000 Series Manuale utente
Cisco
Cisco 1941W Manuale utente
Cisco
Cisco ISR G2 Series Manuale utente
Cisco
Cisco 1605-R Istruzioni operative
Cisco
Cisco WLC 5700 Series Manuale utente
Cisco
Cisco 4948 Series Manuale utente
Cisco
Cisco ASR 9000 Series Manuale utente
Cisco
Cisco 12406 series Guida
Cisco
Cisco NCS 5500 Series Manuale utente
Cisco
Cisco NCS 540 Manuale utente
Cisco
Cisco ISR G2 Series Manuale utente
Cisco
Cisco 220 Series Smart Plus Manuale di istruzioni
Cisco
Cisco 1603R Manuale utente
Cisco
Cisco NCS 5500 Series Manuale utente
Cisco
Cisco 2621XM Manuale di istruzioni
Cisco
Cisco 7206 - VXR Router Manuale utente
