Cisco 4000 Series Manuale utente

Doc. No.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Cisco 4000 Series Rack-Mount and Wall-Mount

Installation

Cisco Product Numbers: ACS-NPRM, ACS-NPWM

This document contains instructions for mounting your Cisco 4000, Cisco 4000-M, Cisco 4500,

Cisco 4500-M, Cisco 4700, or Cisco 4700-M router in a standard 19-inch rack, in a 19-inch telco

rack, or on a wall.

This document contains the following sections:

•Safety Recommendations

•Safety with Electricity

•Required Tools and Parts

•Overview of Rack-Mount and Wall-Mount Procedures

•Preparing the Chassis for Rack-Mounting or Wall-Mounting

•Mounting the Chassis in a Standard Rack

•Overview of Telco Rack-Mounting and Wall-Mounting

•Mounting the Chassis in a Telco Rack

•Mounting the Chassis Shell on a Wall

•Cisco Connection Online

Warning To ensure your safety and the safety of others, be sure the power is OFF and the power

cord is unplugged before working on the router.

78-1009-03

2Cisco 4000 Series Rack-Mount and Wall-Mount Installation

Safety Recommendations

Note All warnings in this document appear in multiple languages in the appendix “Translated

Safety Warnings” in the Cisco 4000 Series Installation Guide.

Safety Recommendations

Follow these guidelines to ensure general safety:

•Keep the chassis area clear and dust-free during and after installation.

•Put the removed chassis cover in a safe place.

•Keep tools away from walk areas where you or others could fall over them.

•Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll

up your sleeves.

•Wear safety glasses when working under any conditions that might be hazardous to your eyes.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

Safety with Electricity

Warning Beforeworkingonequipmentthat is connected to powerlines,removejewelry (including

rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and

can cause serious burns or weld the metal objects to the terminals.

Follow these guidelines when working on equipment powered by electricity:

•Locate the emergency power-off switch in the room in which you are working. Then, if an

electrical accident occurs, you can quickly shut the power OFF.

•Before working on the system, turn OFF the power and unplug the power cord.

•Disconnect all power before doing the following:

—Installing or removing a router chassis

—Working near power supplies

—Performing a memory upgrade

•Do not work alone if potentially hazardous conditions exist.

•Never assume that power is disconnected from a circuit. Always check.

•Look carefully for possible hazards in your work area, such as moist ﬂoors, ungrounded power

extension cables, and missing safety grounds.

•If an electrical accident occurs, proceed as follows:

—Use caution; do not become a victim yourself.

—Turn OFF power to the system.

—If possible, send another person to get medical aid. Otherwise, determine the condition of the

victim and then call for help.

Cisco 4000 Series Rack-Mount and Wall-Mount Installation 3

Required Tools and Parts

—Determine if the person needs rescue breathing or external cardiac compressions; then take

appropriate action.

Required Tools and Parts

The following tools and parts are required for rack-mount and wall-mount procedures:

•Screwdriver, number 1 or number 2 Phillips

•Screwdriver, number 2 ﬂat-blade

For wall-mounting, the following additional equipment is required:

•Plywood board (19 x 19 x 1/2 inch minimum size)

•Wood fasteners for attaching the board to the wall

Table 1 lists the parts contained in the standard rack-mount kit.

Table 1 Standard Rack-Mount Kit Components

Table 2 lists the parts contained in the telco rack-mount and wall-mount kit.

Table 2 Telco Rack-Mount and Wall-Mount Kit Components

Overview of Rack-Mount and Wall-Mount Procedures

The Cisco 4000 series routers can be mounted in a standard 19-inch rack, a telco 19-inch rack, or on

a wall. The procedures for the different mounting options involve removing the front panel and

component tray from the chassis shell and then installing the empty shell in position before

reinserting the component tray.

Quantity Item

2 Rack-mount brackets

2 Short bracket extenders

2 Long bracket extenders

6 M3 machine screws

8 10-32 machine screws

8 8-32 ﬂat-head machine screws

1 Installation diagram

Quantity Item

2 Telco rack-mount or wall-mount brackets

2 M3 machine screws

4 10-32 machine screws

8 8-32 ﬂat-head machine screws

4 Hex-head wood screws (mounts chassis to plywood board)

1 Installation diagram

4Cisco 4000 Series Rack-Mount and Wall-Mount Installation

Preparing the Chassis for Rack-Mounting or Wall-Mounting

Warning Hazardous voltages may exist in or near the power supply, so use extreme caution when

working near the power supply. Before starting any of these procedures, turn OFF power to the

system, unplug the power cord, disconnect any cables at the ports, and connect your ESD-preventive

wrist strap.

Old and New Versions of Chassis Shell

Cisco 4000 series routers have two chassis versions. (See Figure 1.) In the old version of the chassis,

the rack-mount and wall-mount brackets are secured to the chassis with tabs located on the inside of

the chassis shell. Newer versions of the chassis use screws to attach the brackets to the side of the

chassis shell. The rack-mount and the wall-mount brackets supplied with this kit can be used with

both types of chassis.

Figure 1 Old and New Versions of the Cisco 4000 Series Chassis Shell

Preparing the Chassis for Rack-Mounting or Wall-Mounting

To rack-mount or wall-mount the chassis, you must ﬁrst remove the front panel and component tray

from the chassis shell.

Some Cisco 4000 series routers have a safety latch tab on the chassis that affects removing the

component tray. (See Figure 2 and Figure 3.)

If you have a chassis with a safety latch tab, follow the procedure in the following section,

“Removing the Component Tray from a Chassis with a Safety Latch.”

If you have a chassis without a safety latch tab, follow the procedure in the section “Removing the

Component Tray from a Chassis without a Safety Latch,” later in this document.

DATA

OK POWER

DATA

OK POWER

H6082

Old version

Smooth

sides

New version

SERIES

Bracket

mounting

holes

Cisco 4000 Series Rack-Mount and Wall-Mount Installation 5

Preparing the Chassis for Rack-Mounting or Wall-Mounting

Removing the Component Tray from a Chassis with a Safety Latch

Warning Hazardous voltages may exist in or near the power supply, so use extreme caution when

working near the power supply. Before starting any of these procedures, turn OFF power to the

system, unplug the power cord, disconnect any cables at the ports, and attach your ESD-preventive

wrist strap.

Take the following steps to remove the component tray from a chassis with a safety latch:

Step 1 Turn OFF the system power.

Step 2 Attach your ESD-preventive wrist strap.

Step 3 Remove all network and power cables.

Step 4 Loosen the nonremovable screw in the back of the router chassis. The screw is labeled

“Chassis release screw” in Figure 2.

Figure 2 Component Tray Removal for Chassis With a Safety Latch

Warning Before releasing the safety latch, support the component tray from underneath either on

your work surface or with your hands to prevent it from falling (see Figure 2).

Step 5 Slide the component tray out of the chassis shell while facing the rear panel of the chassis,

pulling the handle on the right side of the chassis until the safety latch catches. (See

Figure 2.)

Step 6 Supporting the component tray with one hand, push down on the safety latch tab while you

pull out on the component tray.

Rear of chassis Handle

AUX CONSOLE

INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS

Safety latch tab

Hand supporting

component tray

H1965

Chassis shell

Chassis release

screw

6Cisco 4000 Series Rack-Mount and Wall-Mount Installation

Preparing the Chassis for Rack-Mounting or Wall-Mounting

Step 7 Set the component tray on your work surface.

Step 8 Remove the plastic front panel from the front of the chassis shell by pulling it straight out

using both hands.

Removing the Component Tray from a Chassis without a Safety Latch

Warning Hazardous voltages may exist in or near the power supply, so use extreme caution when

working near the power supply. Before starting any of these procedures, turn OFF power to the

system, unplug the power cord, disconnect any cables at the ports, and attach your ESD-preventive

wrist strap.

Take the following steps to remove the component tray from a chassis without a safety latch:

Step 1 Turn OFF the system power.

Step 2 Attach your ESD-preventive wrist strap.

Step 3 Remove all network and power cables.

Step 4 Loosen the nonremovable screw in the back of the router chassis. The screw is labeled

“Chassis release screw” in Figure 3.

Warning Support the component tray from underneath, either on your work surface or with your

hands, to prevent it from falling.

Figure 3 Component Tray Removal for Chassis Without a Safety Latch

AUX CONSOLE

INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS

H2899

Rear of chassis Handle

Support the component

tray with your hand

Chassis shell

Chassis release

screw

Cisco 4000 Series Rack-Mount and Wall-Mount Installation 7

Mounting the Chassis in a Standard Rack

Step 5 While facing the rear panel of the chassis, pull the handle on the right side of the router

while you support the component tray with one hand. Slide the component tray out of the

chassis shell.

Step 6 Set the component tray on your work surface.

Mounting the Chassis in a Standard Rack

After removing the chassis shell and front panel, you can install the standard rack-mount brackets

into the chassis shell. The standard 19-inch rack-mount kit (see Figure 4) consists of two sets of one

bracket, one short extender (approximately five inches) (see Figure 5), and one long extender

(approximately ten inches) (see Figure 6).

If you have an older version of the chassis, use the ﬁrst of the following procedures to install the

standard rack-mount brackets. If you have a new version of the chassis, use the second procedure to

install the standard rack-mount brackets. After installing the brackets, use the third procedure to

install the chassis shell into a standard 19-inch rack.

Note The brackets provided with your kit ﬁt both the early, tab-mount chassis shells and the newer

screw-mount chassis shells.

Figure 4 Standard Rack-Mount Bracket and Extender

H5962

Front of the chassis

Rack-mount

bracket

Long rear

bracket extender

Rear of the chassis

8Cisco 4000 Series Rack-Mount and Wall-Mount Installation

Mounting the Chassis in a Standard Rack

Figure 5 Short Rack-Mount Bracket Extender

Figure 6 Long Rack-Mount Bracket Extender

Installing Standard Rack-Mount Brackets into an Old Version of the Chassis

Take the following steps to install standard rack-mount brackets into an old version of the chassis

shell:

Step 1 Insert one rack-mount bracket through the slot on each side of the front and rear of the

chassis shell, sliding the rack-mount brackets straight into the shell’s inner tabs (see

Figure 7).

Step 2 Fasten the brackets to each side of the chassis shell with the M3 machine screws provided

(see Figure 8).

H1234a

H1233a

Cisco 4000 Series Rack-Mount and Wall-Mount Installation 9

Mounting the Chassis in a Standard Rack

Figure 7 Rack-Mount Bracket Insertion in an Old Version of the Chassis

Figure 8 Standard Rack-Mount Bracket Installation in an Old Version of the Chassis

Rear of the chassis

H5977

Rack-mount

bracket

M3 machine screw

Front of the

chassis shell

H5979

Rack-mount bracket M3 machine screw

Front of the chassis shell

10-32

machine

screws

10 Cisco 4000 Series Rack-Mount and Wall-Mount Installation

Mounting the Chassis in a Standard Rack

Installing Standard Rack-Mount Brackets into a New Version of the Chassis

Take the following steps to install standard rack-mount brackets into the new version of the chassis

shell:

Step 1 Insert one rack-mount bracket through the slot on each side of the front and rear of the

chassis shell (see Figure 9).

Step 2 Fasten the brackets to each side of the chassis shell with the 8-32 ﬂat-head machine screws

provided (see Figure 9 and Figure 10). Only four 8-32 ﬂat-head machine screws are

required for each bracket.

Figure 9 Standard Rack-Mount Bracket Insertion in a New Version of the Chassis

Figure 10 Standard Rack-Mount Bracket Installation in a New Version of the Chassis

Rear of the chassis

H5959

Rack-mount

bracket

8-32 flat-head

machine screws

Front of the

chassis shell

8-32 flat-head

machine screws

H5960

Rack-mount

bracket

Front of the

chassis shell

10-32

machine

screws

8-32 flat-head

machine screws

Altri manuali per 4000 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Router di rete

Cisco

Cisco RV160W Manuale utente

Cisco

Cisco 2821 - Integrated Services Router Unified Communications... Guida all'installazione

Cisco

Cisco 805 Series Manuale utente

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco CISCO827 Manuale utente

Cisco

Cisco Small Business Pro SRP527W Manuale utente

Cisco

Cisco Cisco 881 Manuale utente

Cisco

Cisco Wireless Express 526 Manuale utente

Cisco

Cisco 7201 Manuale utente

Cisco

Cisco 3825 - Voice Bundle Router Istruzioni operative

Cisco

Cisco RV132W Manuale utente

Cisco

Cisco 2612 Manuale utente

Cisco

Cisco WS-C3550-12G Manuale utente

Cisco

Cisco Cisco ASR 5000 Application Detection and Control Administration... Manuale

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuale utente

Cisco

Cisco NCS 540 Manuale utente

Cisco

Cisco ASR-920-20SZ-M Istruzioni operative e di sicurezza

Cisco

Cisco NCS 5500 Series Manuale utente

Cisco

Cisco 1760 - VPN Bundle Router Manuale

Cisco

Cisco 851-K9 - 851 Integrated Services Router Manuale utente

Cisco

Cisco CRS Manuale operativo

Cisco

Cisco IR829 Manuale

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Guida rapida

Cisco

Cisco 890 Series Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

EnGenius

EnGenius ESR-9710 Manuale utente

LevelOne

LevelOne FBR-1416 Manuale utente

Dynacord

Dynacord Promatrix 6000 Manuale utente

Lorex

Lorex F5D8230-4 Manuale utente