Cisco 860 Series Manuale di istruzioni

CHAPTER

2-1

Cisco Integrated Services Router Hardware Installation Guide

Installing the Router

This chapter describes the equipment and the procedures for successfully installing the Cisco 860, 880,

890 ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs, and contains the following sections:

•Installing the Cisco 810 ISR, page 2-1

•Installing the Cisco 860, 880, 890 ISR, page 2-41

Installing the Cisco 810 ISR

This section contains the following:

•Installing the Cisco 812 ISR, page 2-1

•Installing the Cisco 819 ISR, page 2-19

Installing the Cisco 812 ISR

This section describes the equipment and the procedures for successfully installing Cisco 812 ISR and

contains the following sections:

•Items Shipped with your Router, page 2-2

•Items Shipped with your PoE+ Splitter, page 2-2

•Installing the Cisco PoE+ Splitter, page 2-2

•Installing the SIM Card, page 2-6

•Installing the 3G Antenna, page 2-8

•Mounting the Cisco 812 ISR, page 2-9

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement

1074

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if

interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.

Avoid using such interconnection methods, unless the exposed metal parts are located within a

2-2

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router

Installing the Cisco 810 ISR

restricted access location and users and service people who are authorized within the restricted

access location are made aware of the hazard. A restricted access area can be accessed only

through the use of a special tool, lock and key or other means of security.

Statement 1072

Items Shipped with your Router

Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 812 ISR.

The following items are shipped with your router:

•AC power adapter

•Accessory kit 53-3453-01 which contains the following:

–

Pointer document 78-19961-01

–

RCSI document 78-17665-05

–

Console cable 72-3383-01

•Mounting bracket kit C810-BR-CM

–

Includes screws needed for the installation

•Two 3G Dipole antennas

Items Shipped with your PoE+ Splitter

Unpack the box and verify that all items listed on the invoice were shipped with the Cisco PoE+ splitter

(C810-POE-SPL).

The following items are shipped with your PoE+ splitter:

•GE Cat5 cable

•Power cable

•Power cord lock

•Screws needed for the installation

•Shelf bracket

Note The above items are acceptable for use in Plenums and Air-handling spaces.

Installing the Cisco PoE+ Splitter

The PoE+ splitter (C810-POE-SPL) is an optionalaccessory that is intended to be mounted to the ceiling

tile rails (24 inches span) using the only supported box hanger available from a Cooper B-line BA50

distributor. The screws, cables, and power cord lock needed for the installation are included in the PoE+

splitter accessory kit. A 5 VDC power cable with 1.3 meters in length connects the 5 VDC output of the

PoE+ splitter to the router power input.

To install the Cisco PoE+ splitter, perform these steps:

Step 1 Secure the PoE+ splitter mounting plate into the rail from the BA50 with two 10-24 screws (see

Figure 2-1).

2-3

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router Installing the Cisco 810 ISR

Figure 2-1 10-24 Screws

Step 2 Install the PoE+ splitter into the mounting plate with four 6-32 screws. (See Figure 2-2.)

285667

110-24 screws

2Box hanger

3Shelf bracket (PID 700-39491-01)

2-4

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router

Installing the Cisco 810 ISR

Figure 2-2 6-32 Screws

Step 3 Connect the supplied plenum rated Cat5 cable to the GE0 port on the PoE+ splitter.

Step 4 Connect the Cat5 cable from your PoE+ source to the PoE+ in port on the PoE+ splitter.

Step 5 Place the power cord lock onto the power cord behind the connector overmold as shown in Figure 2-3.

Slide the power cord lock forward so that it captures the overmold and is fully seated.

Figure 2-3 Placement of the Power Cord Lock onto the Power Cord

285668

16-32 screws 3To PoE+ power source

2Power cable with power cord lock installed 4GE CAT5 cable

345076

1Power cord connector

2Power cord lock

2-5

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router Installing the Cisco 810 ISR

Step 6 Install the power cord with power cord lock to the power jack of the PoE+ splitter while making sure

that the two arms of the power cord lock slide into the corresponding slots on the PoE+ splitter and are

fully seated with both arms locking into the slots. Figure 2-4 shows the installation of the power cord

lock and other cables.

In the event that the power cord lock needs to be removed, user your thumb and index fingers to squeeze

the ends of the tabs while pulling away from the PoE+ splitter.

Figure 2-4 Installation of the Power Cord Lock and Other Cables

Step 7 Remove one ceiling tile to gain access.

Step 8 Install the pre-assembled rail with PoE+ splitter into the T-rail. Push down the box hanger mounting clips

to lock into the T-rail as shown in Figure 2-5.

345075

2-6

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router

Installing the Cisco 810 ISR

Figure 2-5 T-Rail

Installing the SIM Card

This section describes how to install and replace the SIM card. Ensure that the router is not mounted to

a wall, rack, or DIN rail.

Caution Do not touch any part of the exposed PCB circuit area when the SIM cover is removed.

Warning

Hot surface.

Statement 1079

To install the SIM card, perform these steps:

Step 1 Power off the router and disconnect the power cable from the power source.

Step 2 Place the router on a sturdy solid surface and orient the SIM access panel up to gain access. Ensure that

any installed antennas are oriented appropriately to avoid damage.

Step 3 Remove the SIM access panel being held in place by four 6-32 screws. (See Figure 2-6).

285669

To POE Power

Source

2-7

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router Installing the Cisco 810 ISR

Figure 2-6 Accessing the SIM Card

Step 4 Remove the SIM card and install the new cards.

Step 5 Reinstall the same 6-32 flat head screws using a screw driver to secure the access panel back in place.

Figure 2-7 shows the SIM card installed and the SIM access panel closed.

344397

2-8

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router

Installing the Cisco 810 ISR

Figure 2-7 SIM Access Panel

Installing the 3G Antenna

Note Install the antenna before you mount the Cisco 812 ISR.

Warning

Do not locate the antenna near overhead power lines or other electric light or power circuits, or

where it can come into contact with such circuits. When installing the antenna, take extreme care

not to come into contact with such circuits, because they may cause serious injury or death. For

proper installation and grounding of the antenna, please refer to national and local codes (for

example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical

Code, Section 54).

Statement 1052

To install the 3G antennas to the router, perform these steps:

Step 1 Manually screw the antenna tight to the TNC connectors on the far left corner of the front panel.

Note It may be easier to straighten out the antenna before attaching it to the TNC connector and then bend it

back to the desired orientation once it is tight.

344398

2-9

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router Installing the Cisco 810 ISR

Figure 2-8 Installing the 3G Antenna

Step 2 Orient the antenna perpendicular with respect to the floor. Figure 2-9 shows the 3G antenna installed.

Figure 2-9 3G Antenna Installed

Mounting the Cisco 812 ISR

This section describes the steps in mounting the Cisco 812 ISR in several configurations, including on

a suspended ceiling, on a hard ceiling or wall, and on an electrical or network box. This section contains

the following topics:

•Mounting Hardware, page 2-10

344395

344396

2-10

Cisco Integrated Services Router Hardware Installation Guide

Chapter 2 Installing the Router

Installing the Cisco 810 ISR

•Mounting Bracket, page 2-10

•Ceiling Grip Clips, page 2-11

•Mounting the Cisco 812 ISR Below a Suspended Ceiling, page 2-13

•Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall, page 2-15

•Mounting the Cisco 812 ISR to a Network or Electrical Box, page 2-17

•Grounding the Cisco 812 ISR, page 2-18

Mounting Hardware

Mounting hardware for the Cisco 812 ISR consists of brackets, which connect to the bottom of the router,

and ceiling grid clips, which connect the bracket to a suspended ceiling. The bracket that you need

depends on the mounting location for the router. The ceiling grid clip that you need depends on the type

of suspended ceiling where you need to install the router. You do not need ceiling grid clips if you are

mounting the router to a hard-surface ceiling or a wall.

Mounting Bracket

The Cisco 812 ISR has only one mounting bracket. The C810-BR-CM universal bracket is versatile. It

works with electrical boxes, can be used for wall mounting, and adapts to ceiling installations.

Figure 2-10 shows the universal bracket installed on the Cisco 812 ISR.

Altri manuali per 860 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Router di rete

Cisco

Cisco RV120W Manuale utente

Cisco

Cisco ASR 5000 Manuale operativo e di manutenzione

Cisco

Cisco Linksys WRT54G3GV2-ST Manuale di istruzioni

Cisco

Cisco 1700 series Manuale utente

Cisco

Cisco NCS 5500 Series Manuale utente

Cisco

Cisco IR809 Manuale utente

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Manuale utente

Cisco

Cisco RV160W Manuale utente

Cisco

Cisco ASR 9000 Series Manuale operativo

Cisco

Cisco Linksys RAN201 Manuale utente

Cisco

Cisco ASR 901 10G Series Manuale

Cisco

Cisco ASR 1013 Manuale utente

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco 3640 Series Manuale utente

Cisco

Cisco WRT610N - Simultaneous Dual-N Band Wireless... Manuale utente

Cisco

Cisco 910 Manuale utente

Cisco

Cisco 815 Manuale utente

Cisco

Cisco 4451-X Manuale

Cisco

Cisco 1805 Manuale utente

Cisco

Cisco UBR924 - uBR 924 Router Istruzioni per il montaggio

Cisco

Cisco ASR 9912 Manuale utente

Cisco

Cisco 3800 Series Manuale utente

Cisco

Cisco Broadband Access Center Manuale utente

Cisco

Cisco ASR1006 - ASR 1006 Modular Expansion Base Manuale

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

EnGenius

EnGenius ESR-9710 Manuale utente

LevelOne

LevelOne FBR-1416 Manuale utente

Dynacord

Dynacord Promatrix 6000 Manuale utente

Lorex

Lorex F5D8230-4 Manuale utente