Cisco ASR 920 series Manuale di istruzioni

Installing the Cisco ASR 920 Series Router

This chapter describes how to install the Cisco ASR 920 Series Router and includes the following sections:

•Prerequisites, page 1

•Installing the Router in a Rack, page 2

•Wall Mounting the Cisco ASR 920 Series Router, page 11

•Install the AC Power Cables, page 14

•Install the DC Power Supply, page 16

•Install and Remove SFP Modules, page 19

•Connect to the 10/100/1000 Ports, page 23

•Install the Chassis Ground Connection, page 25

•Power Connection Guidelines, page 28

•Connect the Chassis to the Network, page 31

Prerequisites

Before installing the Cisco ASR 920 Series Router, it is important to prepare for the installation by:

•Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP).

See “Site Planning”section on page 2-9 .

•Unpacking and inspecting the Cisco ASR 920 Series Router. See “Receiving the Cisco ASR 920 Series

Router”section on page 2-20 .

•Gathering the tools and test equipment required to properly install the Cisco ASR 920 Series Router.

See “Tools and Equipment”section on page 2-21 .

For more instructions on how to prepare for the installation of the Cisco ASR 920 Series Router, see Chapter

2, “Preparing for Installation.”

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Router in a Rack

The following sections describe how to install the Cisco ASR 920 Series Router in a rack. The procedures in

this section apply to both horizontal and vertical mounting of the router in a rack:

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To

install the brackets on the front of the chassis, perform these steps:

SUMMARY STEPS

1. Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.

2. Position one of the brackets against the chassis side, and align the screw holes.

3. Secure the bracket to the chassis with the screws removed when performing Step 1 . The recommended

maximum torque is 10 in.-lb.

4. Repeat Step 2 and Step 3 for the other bracket.

DETAILED STEPS

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.

The figure below shows how to attach the brackets at the front, middle, and rear positions on the Cisco ASR 920 Series

Router for a 19-inch EIA rack.

Figure 1: Attaching Mounting Brackets for a 19-inch EIA Rack (Front, Middle, and Rear Positions)

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Router in a Rack

Figure 2: Shows how to attach the brackets on the Cisco ASR 920 Series Router for a 23-inch cabinet.

Figure 3: Attaching Mounting Brackets for a 23-inch Cabinet (Front, Middle, and Rear Positions)

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Chassis Brackets

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Chassis Brackets

Figure 4: Attaching Mounting Brackets for a 300 mm ETSI Cabinet (Front, Middle, and Rear Positions)

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Chassis Brackets

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1 . The recommended maximum torque

is 10 in.-lb.

Step 4 Repeat Step 2 and Step 3 for the other bracket.

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Chassis Brackets

Installing the Router Chassis in the Rack

Ensure adequate air flow when mounting the router in a rack. For more information, see the “Air Flow

Guidelines”section on page 11 .

Note

Install the cable guides before installing the router in a 19-inch EIA rack. See Attaching the Cable Guides.Note

To install the router chassis in the equipment rack, perform these steps:

SUMMARY STEPS

1. Position the chassis in the rack as follows:

2. Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment

rack.

3. Install the four M6x12mm zinc-plated steel screws through the holes in the bracket and into the threaded

holes in the equipment rack posts.

4. Use a tape measure and level to verify that the chassis is installed straight and level.

DETAILED STEPS

Step 1 Position the chassis in the rack as follows:

•If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting

posts.

•If the rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.

Step 2 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Installing the Router Chassis in the Rack

The following figure shows how to install the Cisco ASR 920 Series Router in a 19-inch EIA rack.

Figure 5: Installing the Chassis in a 19-inch EIA Rack

Step 3 Install the four M6x12mm zinc-plated steel screws through the holes in the bracket and into the threaded holes in the

equipment rack posts.

Step 4 Use a tape measure and level to verify that the chassis is installed straight and level.

Attaching the Cable Guides

The Cisco ASR 920 Series Router supports the following cable guides:

•A920-CBL-GUIDE (left and right)—help in routing the cables from all components on the front panel

thereby enabling a proper cable-bending radius.

If the chassis is mounted using 19-inch brackets, you must assemble the cable guides before installing the

chassis on the rack.

Note

To install the cable guides, perform these steps:

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Attaching the Cable Guides

SUMMARY STEPS

1. Position the cable guide-left and cable guide-right against the front of the chassis and align the four screw

holes, as shown in the fgure below.

2. Secure the cable guides with the four M6x12mm screws supplied with the cable kit. The recommended

maximum torque is 3N-m.

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Attaching the Cable Guides

DETAILED STEPS

Step 1 Position the cable guide-left and cable guide-right against the front of the chassis and align the four screw holes, as shown

in the fgure below.

Figure 6: Cable Guide Installation For 19-inch Rack Brackets

Figure 7: Cable Guide Installation For ETSI Rack Brackets

Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide

Installing the Cisco ASR 920 Series Router

Attaching the Cable Guides

Altri manuali per ASR 920 series

Indice

Altri manuali Cisco Router di rete

Cisco

Cisco 827-4V - 827-4V Router - EN Guida rapida

Cisco

Cisco Small Business SRP520-U Manuale utente

Cisco

Cisco Catalyst 3850 Manuale operativo

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco Nexus 7000 Series Manuale di istruzioni

Cisco

Cisco Small Business Pro SRP527W Manuale utente

Cisco

Cisco 7206VXR - VPN Bundle Router Manuale utente

Cisco

Cisco Catalyst 2900 Series XL Manuale utente

Cisco

Cisco QuickVPN - PC Manuale di istruzioni

Cisco

Cisco IR809 Manuale utente

Cisco

Cisco 880 Series Manuale utente

Cisco

Cisco IR829 Manuale

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuale utente

Cisco

Cisco 819 series Manuale utente

Cisco

Cisco WS-C3550-12G Manuale utente

Cisco

Cisco Linksys WET54G-EU v3 Manuale utente

Cisco

Cisco ASR 907 Manuale di istruzioni

Cisco

Cisco 910 Manuale utente

Cisco

Cisco XR 12000 Manuale di installazione

Cisco

Cisco CRS Manuale utente

Cisco

Cisco SCE8000 GBE Manuale utente

Cisco

Cisco Network Registrar none Manuale utente

Cisco

Cisco Small Business RV220W Manuale utente

Cisco

Cisco Linksys E900 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

EnGenius

EnGenius ESR-9710 Manuale utente

LevelOne

LevelOne FBR-1416 Manuale utente

Dynacord

Dynacord Promatrix 6000 Manuale utente

Lorex

Lorex F5D8230-4 Manuale utente