Cisco IR1101 Manuale utente

Product Overview

This section contains the following:

•Product Overview, on page 1

•General Description, on page 1

•SKU Information, on page 2

•Cisco IR1101 Series Platform Features, on page 3

•Front Panel Icons and LEDs, on page 12

•Supported Cisco Antennas and Antenna Accessories, on page 14

•Modem Support, on page 14

•Power Supply, on page 17

•RJ45 Ports, on page 18

•Ethernet and Optical SFP Modules, on page 19

•DSL SFP Module, on page 20

Product Overview

This chapter provides an overview of the features available for the Cisco IR1101 Industrial Integrated Services

Router and its Expansion Module. It contains the following sections:

Prior to installing this device read the Regulatory Compliance and Safety Information .

Note

General Description

The Cisco IR1101 Industrial Integrated Services Router is a next generation modular industrial router which

has a base module with additional Pluggable Modules that can be added. The Pluggable Module provides the

flexibility of adding different interfaces to the IR1101 platform, for example, a cellular module.

The IR1101 ISR also has an Expansion Module that adds key capabilities such as dual LTE Pluggables,

mSATA SSD FRU, SFP, and Digital GPIO connections.

Product Overview

Figure 1: The IR1101 Industrial Integrated Services Router

SKU Information

The following table lists the different SKUs available for the Cisco IR 1101.

Table 1: Supported SKUs for Cisco IR1101

DescriptionSKU ID

IR1101 Base UnitIR1101-K9

Expansion Module with 1 GE SFP, 1 Pluggable Module, 1 Digital I/O Connector, and 1 mSATA SSD

Slot.

IRM-1100-SPMI

Expansion Module with 1 GE SFP and1 Pluggable Module.IRM-1100-SP

100 GB mSATA SSDIR1100-SSD-100G

Optional AC power adapter with 110/220V AC and 88-300V DC input (Temperature: -40C to 60C)PWR-IE50W-AC

Din rail kit and mounting screws for horizontal and vertical mountingIR1101-DINRAIL(=)

Din rail kit for the Expansion ModuleIRM-1100-DINRAIL

Wall mount kitIR1101-WALLMNT(=)

Product Overview

SKU Information

Cisco IR1101 Series Platform Features

This section describes the different components of the router.

Cisco IR1101 Base Router

The following lists the hardware platform features for the Cisco IR1101.

• External Power Entry

• Nominal: 12 to 48VDC

• Absolute min/max: 9.6 to 60VDC

• Typical current: 0.82A to 0.22A

• Maximum current: 0.91A to 0.28A

• 4-pin 3.8 mm EURO power connector

• External Reset/Recovery Push Button

• Gigabit Ethernet Combo RJ45+SFP connector.

• RJ45 connector will support IEEE802.3 Ethernet over copper wiring standards of 10Base-T,

100Base-TX, and 1000Base-T

• SFP port will support 1000Base-X or 100Base-FX Fiber Ethernet standard SFP

• LAN Ports

• 4x RJ45 10/100 Fast Ethernet

• Serial Port

• 1 x RJ45 RS232 Port (DTE)

• USB Ports

• 1x USB 2.0 Type A Host Port

• 1x USB 2.0 mini USB Type B console port

• Compliance

• Class A EMC or better

• IP30 compliant when vertical and ports downward

• Industrial temperature [-40ºC to +60ºC, 13.8Kft (operating), 15Kft (non-operating)]

• One alarm input

The following graphic shows the IR1101 ISR base router.

Product Overview

Cisco IR1101 Series Platform Features

Figure 2: Cisco IR1101 Industrial Integrated Services Router

The following graphics show the IR1101 Base Module Front.

Figure 3: Cisco IR1101 Integrated Services Router with USB covers in place

DetailsItem

USB 2.0 Port Cover1

Mini-USB Console Cover2

Product Overview

Cisco IR1101 Base Router

The following graphic shows the front panel details of the Cisco IR1101.

Figure 4: Cisco IR1101 Front Panel

Table 2:

SFP GE WAN1

USB 2.02

RJ45 GE WAN3

Serial Port4

FE LAN Ports 1-45

Grounding Point (on side of device)6

DC Power and Alarm Input7

Mini-USB Console8

Reset Button9

Pluggable Module10

Cisco IRM-1100-SPMI Expansion Module

The following graphic shows the IR-1100-SPMI Expansion Module.

Product Overview

Cisco IRM-1100-SPMI Expansion Module

Figure 5: IR-1100-SPMI Expansion Module

The following lists the hardware platform features for the Cisco IR-1100-SPMI:

• 1 GE SFP

• 1 Pluggable slot

• 1 Digital I/O connector

• 1 mSATA SSD slot

Figure 6: IR-1100-SPMI Expansion Module Details

Product Overview

Cisco IRM-1100-SPMI Expansion Module

4 GPIO + 1 Return (Digital I/O)1

SFP Connector2

Pluggable Module3

mSATA SSD Slot4

Digital I/O LEDs5

Digital I/O Connector

The Digital I/O connector has 4 GPIO connections plus 1 Return connection. The Digital I/O supports Both

Dry and Wet contacts up to 60Volts.

• Dry contact is isolated from a voltage source (or “No Volt”), with an embedded relay function (NPN

transistor), usually used to indicate an event. For example: open/close, alarm.

• Wet contact is a contact with external power (+3.3V to +60V, max 150mA of current allowed at high

voltage) applied, usually used to energize something. For example: solenoid, light.

The following graphic shows the connector.

Digital I/O is only supported on IOS-XE version 16.12.1 and above.

Note

The default state of the Digital I/O is input, the open-collector is open (off).

Note

Figure 7: Digital I/O connector

The pinouts for the Digital I/O are described in the following table.

Table 3: Digital I/O Pinouts

DescriptionDirectionNamePin

Digital IO 1I/ODIO11

Digital IO 2I/ODIO22

Digital IO 3I/ODIO33

Product Overview

Digital I/O Connector

DescriptionDirectionNamePin

Digital IO 4I/ODIO44

Digital IO Common ReturnReturnReturn5

Digital Input and Output Specifications are described in the following tables.

Digital Input Specification is considered “dry contact”, and Digital Output Specification is considered “wet

contact”.

Table 4: Digital Input Specification

UnitMaximumMinimumSpecification

Volts602.2Input Voltage High

Volts1.2-Input Voltage Low

uA0.68mA

Note1

-Input Current

Note1: Current is flowing out of the terminal although it is an input, i.e. sourcing. The current is flowing in

the terminal for the output, i.e. sinking.

Table 5: Digital Output Specification

NotesUnitMaximumMinimumSpecification

No external voltage

applied.

Volts2.5Output Voltage High

No external voltage

applied.

Volts0.4-Output Voltage Low

Ohms3.3K – 1%3.3K – 1%Internal Pull-up

Resistance

Volts3-Internal Pull-up Voltage

External resistance

required to limit current

to 200mA.

Volts603.3External Pull-up Voltage

mA200Sink Current

Common features of the Digital I/O are:

• Withstands up to 60V applied at the terminal.

• Reverse voltage protected and causes no damage to the equipment.

• Digital input and output can coexist on different channel.

Product Overview

Digital I/O Connector

• LED Indicator: provision-able, On: Active, Off: Non-active.

• Electrical isolation: 2000 VDC.

• 4kV Surge protected (IEC 61000-4-5).

IR-1100-SPMI Expansion Module LEDs

There are 6 LEDs in the Expansion Module. Four LEDs show the status of digital input and output. One LED

shows the SFP port status and one LED shows the mSATA status. The LED behavior is shown in the following

table.

Table 6: Expansion Module LEDs

DefinitionLED

Off - InactiveSolid Yellow- ActiveDigital I/O as Input

Off - InactiveSolid Yellow- ActiveDigital I/O as Output

Off - No LinkSolid Yellow - Port link with no activityFlashing Yellow - Port link healthy with activitySFP

Off - Not powered on or no activityFlashing Green - mSATA being accessedmSATA

Cisco IR-1100-SP Expansion Module

The IR-1100-SP Expansion Module is the same as the IR-1100-SPMI module, without the Digital I/O and

mSATA components.

The following lists the hardware platform features for the Cisco IR-1100-SP:

• 1 GE SFP (see the supported list of SFP’s here: SFP Module, page 26 )

• 1 Pluggable slot

Cisco Pluggable Module

The Pluggable Module provides the flexibility of adding different interfaces to the IR1101 platform, for

example, a cellular module.

Pluggable LTE Module

Highlights of the LTE Pluggable Module are:

• All Cellular interfaces are supported through a Pluggable Module

• Micro-Sim, 3FF size. Cisco recommends Industrial Temp micro SIMs that are rated from -40C to +105C.

The following two figures show an example of a Pluggable Module. In this case, the LTE Pluggable Module.

Product Overview

IR-1100-SPMI Expansion Module LEDs

Figure 8: LTE Pluggable Module (front)

LTE-Main SMA1

GPS SMA2

Micro USB Debug Port3

LTE-Div SMA4

Figure 9: LTE Pluggable Module (with antennas)

LTE Category 18 Pluggable Module

This module has a new smaller form factor SMA Diversity Antenna for usability and Micro-USB port access.

Product Overview

LTE Category 18 Pluggable Module

Altri manuali per IR1101

Indice

Altri manuali Cisco Router di rete

Cisco

Cisco CISCO7206 Manuale utente

Cisco

Cisco 3825 Series Manuale di servizio

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco RVS4000 - Gigabit Security Router Manuale utente

Cisco

Cisco Catalyst 2900 Series XL Manuale utente

Cisco

Cisco 7204 - VXR Router Manuale di istruzioni

Cisco

Cisco 12016 Manuale utente

Cisco

Cisco Soho 78 Manuale utente

Cisco

Cisco Internet Router Cisco 12404 Manuale utente

Cisco

Cisco 5428 - SN Router Manuale

Cisco

Cisco WS-C2950-24 Manuale utente

Cisco

Cisco ASR 5000 Series Istruzioni operative e di sicurezza

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco ASR 903 Manuale

Cisco

Cisco Unified Communications Manager 8.5(1) Manuale utente

Cisco

Cisco 12406 series Manuale dell'operatore

Cisco

Cisco Profile Series Manuale utente

Cisco

Cisco 2950 - Catalyst Switch Manuale utente

Cisco

Cisco VIC-2FXO - 3600 Voice Interface Card-Fxo... Istruzioni originali

Cisco

Cisco NCS 5000 Series Manuale utente

Cisco

Cisco RVS4000 - Gigabit Security Router Manuale di istruzioni

Cisco

Cisco ASR-920-20SZ-M Istruzioni operative e di sicurezza

Cisco

Cisco 4948 Series Manuale utente

Cisco

Cisco 806 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

EnGenius

EnGenius ESR-9710 Manuale utente

LevelOne

LevelOne FBR-1416 Manuale utente

Dynacord

Dynacord Promatrix 6000 Manuale utente

Lorex

Lorex F5D8230-4 Manuale utente