Claas AVERO Guida all'installazione
Information and Basic Field
Settings for AVEROVERSION 14
1
Contents
Title Pages
Introduction 2
Safety 3
Overview 4
Cab and controls 5 - 8
AUTO CONTOUR 19 -12
Adjustments 15
Cutterbar 16 -18
Threshing 19
Separation 20 -21
Cleaning 22 -24
Settings aid 25 -26
Loss calculations 27 -28
Maintenance 29
Useful part numbers 30
Wet harvest recommendations 31 -32
2
Introduction
This quick reference guide has been produced to aid operators with familiarisation and
settings for the CLAAS AVERO combines.
CLAAS combines are designed for output and efficiency but this can only be achieved
with correct operation and maintenance of the machine.
This guide is not designed to replace the Operators Manual but merely as a reference
document. More in depth information is available in the Operators Manual.
ALWAYS READ THE OPERATORS MANUAL BEFORE OPERATING YOUR COMBINE
.
Down time costs output
To get the most from the machine, the wheels must be turning. In order to keep
downtime to a minimum, it’s vital that routine maintenance is not neglected. As well as
servicing the machine according to the operator’s manual, a good check of the
machine is essential. It is false economy to put off the replacement of worn parts until
they break. For example, a cracked knife section will take 5 minutes to change before
starting work, but usually a minimum of 10 minutes output will be lost, once work has
begun.
Abbreviations
Throughout this guide the following abbreviations are used:
‘LHS’ and ‘RHS’ refer to the Left Hand Side and Right Hand Side of the machine
respectively, taken from the rear of the machine facing in the direction of travel
APS –Accelerated Pre-Separation, refers to the accelerator drum in front of the main
drum
ISS –Refers to the Intensive Separation System over the straw walkers.
3
Safety
Safety is of the utmost importance whilst you are operating and maintaining your
combine harvester. Make sure that all of the risks are assessed to reduce the likelihood
of an accident.
Make sure you are familiar with the controls and operation of the machine and have
read the operators manual
The combine harvester has many moving parts, guards are designed to keep you
safe, please ensure that all guards are kept in place and in good condition when
operating the machine.
When doing any maintenance work or making adjustments outside of the machine
make sure that the engine is switched off and the battery isolator key is removed.
If you need to go underneath the front elevator/ cutterbar to make adjustments/
clean concaves, preparation pan, etc. Make sure that the cutterbar lift cylinder lock is
in place.
Some of the maintenance has to be carried out at height, please asses the risks that
this poses and ensure that the task is carried out safely.
When operating the machine be aware of the presence of people particularly in
farmyards, always get someone to help you when reversing in confined areas.
Be aware of the size of your machine, particularly the height, you may be at risk from
contact with overhead power lines and overhead obstructions particularly but not
exclusively when the graintank lids are up and if extra aerials have been fitted to your
machine.
For more in depth safety information please consult your operators manual. Other
information is available on the HSE website: www.hse.gov.uk
Always read the Operators Manual before using any new machine.
4
1. Crop divider
2. Reel
3. Cutterbar auger
4. Feeder chains
5. Stone trap
6. APS concave
7. APS drum
8. Main drum
9. Impeller
10. Straw walker
11. Intensive separator system
12. Preparation floor
13. Fan
14. Top sieve
15. Bottom sieve
16. Clean grain auger
17. Returns auger
18. Unloading auger
19. Straw chopper
20. Engine
5
Right Hand Console
1. Straw walker loss sensitivity
2. Sieve loss sensitivity
3. Cutterbar reverser
4. Cross levelling
5. Vario in / out (if fitted)
6. Front attachment on / off
7. Menu selection switch
9. Menu settings switch
10. Reel speed adjustment
11. Auto reel speed
13. Fan / Drum speed selection
14. Drum speed adjustment
15. Fan speed adjustment
18. Threshing on / off
25. Engine speed
26. Left rape knife switch
31. Learning front attachment
6
Multifunction lever
1a. Front attachment lower
1b. Front attachment raise
1c. Pre set cutting height (slow lower when not threshing
out of gear)
1d. Pre set ground pressure (slow raise when threshing
not in gear)
4a. Reel lower
4b. Reel raise
4c. Reel forward
4d. Reel backwards
5. Front attachment stop
6. Grain tank auger on/off
7. Grain tank unloading tube
7a. Unloading tube swing out
7b. Unloading tube swing in
7
CIS –Display Screen
1 Fault or warning messages
2. Display window (forward speed, operating hours, faults)
3. Fuel level
4. Engine coolant temperature
5. Drum speed is displayed
6. Fan speed is displayed
7. Speed gauge for drum/fan
8. Cutterbar ground pressure
9. Cutting height
10. Area counter
11. Straw walker losses
12. Performance monitor 70% mark
13. Sieve losses
8
CIS –Harvest display
1. Feed rake conveyor slip
2. Clean grain elevator slip
3. Returns elevator slip
4. Straw walker slip
5. Straw chopper slip
6. Grain tank unloading on
7. Unloading tube out
8. Straw walker blockage
9. Grain tank 70% full
10. Grain tank 100% full
11. .Hydraulic oil level
12. Engine air filter blocked
13. Low engine coolant leve
14. Hand brake applied
15. Engine oil pressure low
16. Air conditioning defective
17. Major alarm
18. Attention alarm
19. Fuel level below 10%
20. Engine coolant temp high
9
AUTO CONTOUR
Cutting height
The cutting height is displayed above the bar (A) between the
numbers 100 and 55. (Numbers are only for illustration use
and are not on the Combine)
100 = Cutterbar skids do not touch the ground and the
sensing bars are fully swung out.
55 = Cutterbar skids have slight contact with the ground so
the sensing bars are fully swung in.
(A) Is the ATUO CONTOUR sensitivity which is set at 45% but is
fully adjustable. 100% = maximum sensitivity, 0% =
no response from sensing bars.
Ground pressure
The ground pressure is displayed with the black bars below
(A), in this example between numbers 55 and 0.
55 = Cutterbar skids have slight contact with the ground so
the sensing bars are fully swung in.
0 = The full weight of the Cutterbar is on the ground.
Cutting height control
Indice
Altri manuali Claas Attrezzature agricole
Claas
Claas 930 Guida all'installazione
Claas
Claas TARGO K50 Istruzioni operative
Claas
Claas ROLLANT 66 Istruzioni operative
Claas
Claas DOMINATOR 68 S Manuale utente
Claas
Claas LEXION 780 Guida all'installazione
Claas
Claas DOMINATOR 208 MEGA III Manuale utente
Claas
Claas LEXION 600 Istruzioni operative
Claas
Claas LEXION 580 R Manuale utente
Claas
Claas LEXION 8000 Guida all'installazione
Claas
Claas TUCANO 2017 Guida all'installazione
Claas
Claas TUCANO 500 Guida all'installazione
Claas
Claas RU 450 Manuale utente
Claas
Claas LEXION 670 Manuale utente
Claas
Claas MEDION 340 Istruzioni operative
Claas
Claas C490-C370 Istruzioni operative
Claas
Claas QUANTUM 3500 Guida
Claas
Claas QUADRANT 5300 Manuale utente
Claas
Claas LEXION 560 Manuale utente
Claas
Claas QUADRANT 3400 Istruzioni operative
Claas
Claas DOMINATOR 150 Manuale utente
