Clare Controls Clare Video Doorbell Version 2 Manuale utente
Clare Video Doorbell
Version 2 User Manual
Index
Doorbell buttons and features............................................................................3
What’s included in the box....................................................................................4
Clare Video Doorbell power requirements..................................................5
Wi-Fi signal strength requirements..................................................................6
Getting started..............................................................................................................7
Preparing the Video Doorbell for wall mounting....................................8
Connecting power to the Video Doorbell...................................................9
Mounting the Video Doorbell and restoring power........................... 10
Installation when using a digital doorbell chime................................. 11
Getting started with the ClareVision Plus App....................................... 12
Setting up the Video Doorbell in the ClareVision Plus App....13-14
Installing the faceplate and restoring power.......................................... 15
Troubleshooting and Light Status ................................................................. 16
Conguring the motion detection area..................................................... 17
Adjusting the sensitivity of the motion detection area.................... 18
Using the ClareVision Plus App.........................................................................19
Frequently asked questions............................................................................... 20
Customer and technical support ................................................................... 21
Welcome To Your New Clare
Video Doorbell
180º 2MP HD Camera
Omni-directional
Microphone
Doorbell Button
Mode Button
Uses Existing
Doorbell Wiring
Micro-SD card
Getting
Started
3
Getting
Started
Check Out What’s Included
In The Box.
4 Interchangeable
faceplates
Mounting
template
Clare Video
Doorbell camera
4 Terminal
screws
3 Mounting
screws
2 Wire extensions 2 Security
screws
3 Wall anchors 1 Security key1 Drill bit4 Wire connectors 1 Resistor
Wedge and spacer
3 Wedge or
spacer screws
4
Getting
Started
The easiest way to know if you currently have a mechanical or digital
doorbell, is to listen to the tone your doorbell makes when you ring it.
If it makes the standard ding-dong sound, it is most likely a mechanical
doorbell. If your doorbell plays a dierent tone or melody, it’s most likely
a digital doorbell and you must install the supplied resistor. Refer to
Install Step 4 for more information on installing the resistor.
Mechanical vs. Digital Doorbells
The Clare Video Doorbell will work with mechanical
and digital doorbells that use 16-24VAC power only.
NOTE: If you are unsure what voltage your doorbell uses, please
consult your original doorbell packaging or a licensed electrician.
Clare Video Doorbell
Power Requirements
Mechanical Digital
FRONT TRANS REAR
5
The Clare Video Doorbell can only be connected to a
2.4GHz wireless network, and requires a minimum of -60dBm of
Wi-Fi signal strength at the installation location.
We recommend downloading a Wi-Fi analysis tool for your phone or
tablet to check signal strength. Stand in the location of where the video
doorbell will be installed, and test the strength of the Wi-Fi. If a -60dBM
signal or better is not achievable, we recommend installation of a Wi-Fi
range extender or Wireless Access Point (WAP) to ensure proper video
and audio streaming.
Wi-Fi Signal Strength
Requirements
For a list of recommended Wi-Fi signal
strength Apps and tools, visit the link
below.
For a list of compatible mechanical
and digital doorbell chimes, visit the
link below.
http://bit.ly/2xoCAt5http://bit.ly/2sVmsOG
Getting
Started
6
Getting
Started
Before starting installation,
make sure to shut o the power
being supplied to your doorbell at
the breaker panel.
Next, remove your existing
doorbell and disconnect the wires
connected to the screws on the
back.
Install
Step 1
Diagram 1
7
Preparing The Video Doorbell
For Wall Mounting
Install
Step 2
Remove the faceplate attached to the
Video Doorbell to access the mounting
holes used for installation. Refer to
diagram 2 on how to easily remove
the faceplate.
Next, refer to diagram 3 to mount the
supplied spacer or wedge plate to the
doorbell location using the supplied
wedge or spacer mounting screws.
The angled wedge plate can be used
to change the viewing angle of the
Video Doorbell. Make sure to pull the
doorbell wires through the center of
the wedge plate or spacer.
Diagram 2
Diagram 3
Mounting
screws
x2
Required
hardware
8
Next, refer to diagram 4 to connect your
existing doorbell wiring to the leads
located on the back of the Video Doorbell.
If your existing wiring is not long enough,
follow the instructions below to extend
your wiring.
To extend the existing wiring use the provided
wire extenders and easy-to-use connectors.
Insert the wires into the connectors as shown
in diagram 5 and use pliers to snap the button
into place. There is no need to strip any wires
as the connectors will pierce the insulation
for you.
Note: The two wires used to power the Video
Doorbell can be hooked up to either terminal.
Diagram 4
Diagram 5
Connecting Power To The
Video Doorbell
Install
Step 3
Terminal
screws
x2
Required
hardware
Wire
extenders
x2
Optional
hardware
9
Wire
connectors
x2
Optional
hardware
Indice
Altri manuali Clare Controls Sistema di interfono
