Clarke CWB1830S Manuale utente
ASSEMBLY INSTRUCTIONS
GC10/12
Heavy Duty Workstation
Model: CWB1830S (with lower half shelf)
Part No: 7637855
2
INTRODUCTION
Thank you for purchasing this CLARKE product. Before assembling the
workstation, be sure to read these instructions thoroughly. In doing so you will
ensure the safety of yourself and of others around you, and you can look
forward to the product giving you long and satisfactory service.
(Safe working load,-300kg (full shelf )/100kg (shelves) UDL.
CONTENTS (shown with boards removed)
ASSEMBLY
The tabs of the beams will often enter the slots fully using just firm
hand pressure but if they are too tight, you may require a rubber mallet or
hammer to assist. If so, always use a cloth to protect the product paint finish.
Post A Post B
Post
C
Mid End
Beam
Upper End
Beam
Shelf
Support
Beam
Lower End
Beam
Plastic
Foot
Centre Support
1x Shelf Support Beam I
2x Mid End Beams J
2
x Lower End Beams (with holes) K
x Upper End Beams4 L
2x Shelf Clips M
2xSmall Boards N
1xMedium Board O
x Large Board
1P
2xPosts (750mm long)
A
2xPosts (1678mm long)
B
2xPosts (917mm long)
C
6xPlastic Feet
D
6xPlastic Post Caps
E
1xCentre Support F
2xLong Beams (with holes) G
5xLong Beams (without holes) H
E
H
I
F
L
D
J
K
Long Beam
Plastic Post
Cap
G
Long Beam
3
1. Lay out and identify the three different lengths of post. These can be
identified from the table of contents.
2. Connect the post B & C together
using an mid end beam J as
shown in Fig 1 & Fig 2.
•When using a hammer or mallet,
always strike the edge closest to
the post and protect the paint
with a cloth.
•Only use the mallet to tap gently,
ensuring the tabs of the support
pieces are in line with the slots in
the posts.
3. Decide how high you want the
lower shelf to be, relative to the
floor, and connect a lower end
beam K to complete an end
frame assembly as shown
in Fig 2.
Note that the lower shelf should
be less than half distance from
floor to large shelf for optimum
stability.
4. Repeat this again for the other
end assembly, making sure that
the corresponding lower end
support is at the same height.
Note that the edge with the wider
flange should be installed
uppermost to touch the shelf and that the face with open edges should
face the rear of the unit.
FIG 4
FIG 1
Post B
Slots
Post B Mid End Beam J
FIG 2
Lower End
Beam K
Post C
FIG 3
G
J
Mid End
Beam
Front
Long
6. Fit the centre support F between
the lower end beams K
as in Fig 4.
5. Now fit the front long beam G
and rear long beam G to match
the mid end beams J , thereby
joining the two end frame
assemblies together as in Fig 3.
Add a long beam H at the rear
to support the lower shelf.
Beam
Lower
Centre Support
End
Beam K
F
SAFETY ADVICE
•Always place heavier items on the lower shelves.
•Always evenly distribute your loads across the shelves where possible.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose. Faulty goods
should be returned to their place of purchase, no product can be returned to
us without prior permission.
This guarantee does not effect your statutory rights.
FIG 5
Shelf
Support
Beam
Plastic
Foot
Post
FIG 6
FIG 7
Upper
End
Beam
Plastic Post Cap
I
A
D
L
E
7. Slot the shelf support beam
between the long beams
to carry the large board
as in Fig 5.
I
G
P
8. Fix the shelf clips to the centre
support and place the medium
board on the half shelf.
M
F
O
9. Fix the plastic foot to the post
as shown in Fig 6.
•These will locate the posts in
position on the large board .
DA
A
P
11. Add the remaining long beams H
12. Position the small boards on the
upper shelves.
N
13. Fit the plastic post caps provided
to the exposed ends of post A &
B .
E
10. Fit the upper end beams
between the posts A and B , with
posts sitting on the plastic
feet.
A
D
L
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Clarke Scrivania
