Clarke DEVIL 910SS Manuale utente

USER INSTRUCTIONS

GC0816

GAS HEATERS

MODEL NOS: DEVIL 700, 900/910SS,1600/

1610SS & 2100

PART NOS: 6920182, 6920186, 6920188, 6920190, 6920192, &6920194

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Gas Powered Heater.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials. Metal

products should be taken to your local civic amenity site for recycling of metal

products.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INFORMATION

Signs of Carbon Monoxide poisoning are headaches, dizziness and/or nausea.

Should anyone show these signs, they must GET FRESH AIR IMMEDIATELY. Turn

off the heater and have it serviced before using again.

Pregnant women, persons with a heart or lung condition, anaemia or under

the influence of alcohol, or those at high altitude, are more likely to be

effected by Carbon Monoxide.

Read, and make sure you fully understand the following precautions and the

hazards associated with this type of heater.

• Use only liquid propane gas with this heater.

• Ensure the Propane gas bottle, gas hose and electric cable, are

positioned behind the unit, well away from the heat.

• Ensure gas hose and regulator connections are gastight and the hose is

not kinked.

• Never use the heater where flammable vapours or if a high dust content

is present in the air.

• Only use with the voltage specified and ensure the heater is properly

earthed.

• Use only in well ventilated areas. Provide ventilation of at least 3 square

feet of fresh air for every 100,000 BTU/hr of rating.

• The minimum clearance from any combustible materials is 4 feet

(125cm) between the rear, top or sides of the heater and walls or other

obstructions.

• Keep the heater at least 6 feet from propane tanks and do not point the

heater at propane tanks within 20 feet.

• Stand the heater on a stable, level surface whilst hot or operating. If the

heater should overturn, a fire could occur.

• Keep children and animals away from heater at all times.

• Use heater in accordance with all fire regulations.

• Never use heater for domestic heating in living or sleeping areas.

• Never leave a heater plugged in without adult supervision if children or

animals are likely to be present.

WARNING: LACK OF VENTILATION CAN CAUSE CARBON MONOXIDE

POISONING.

WARNING: CARBON MONOXIDE POISONING CAN KILL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Never move, handle, replenish the gas supply or service the heater

when it is hot, operating or plugged in.

• Never attach the heater to any duct work, or impede air flow into or out

of the heater.

• Disconnect the heater from the power supply when not in use.

• Use ONLY the factory pre-set regulator supplied with the heater.

• If the heater works for long periods at maximum capacity, be aware

that it is possible for ice to form on the gas cylinder due to excessive

evaporation.

• Never direct hot air towards the cylinder in order to de-ice.

• Never use in wet areas, basements or below ground level. Propane gas

is heavier than air and will sink to the lowest possible level.

• Always ensure the heater is correctly maintained in accordance with

this manual.

SAFETY SYMBOLS

Please read all of the safety and operating instructions carefully before using

this product. The following safety symbols may be found on the product.

General hazard

warning

Danger-Hot Surfaces.

Always read the

manual before use

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING

When unpacking, check the heater for possible shipping damage. Should any

damage be apparent, please notify your Clarke dealer immediately.

Your heater is fully assembled,- only the electrical and gas supplies need

connecting. Retain any plastic cover caps (attached to the inlet connector

and hose/regulator assembly) for future storage.

PROPANE GAS SUPPLY

These heaters are designed for use with PROPANE GAS ONLY. Gas cylinders are

not supplied, but are readily available from builders merchants or gas suppliers

etc.

This range of portable, direct fired gas heaters is designed to BS 4096 for

industrial applications to give safe, efficient and reliable operation.

As with all mechanical equipment, optimum performance will only be

achieved if the correct operation and servicing procedures are followed.

GAS CONNECTION

Connect the free end of the gas hose to the gas inlet connection on the

heater and tighten to ensure there are no gas leaks. Before attaching the

regulator to the gas cylinder, ensure the mating parts are free from grease and

dirt and are undamaged.

Fit the regulator to the cylinder,

tightening the thread as tight as

possible with a propane spanner,

noting that the threads are LEFT

HANDED. To check for leaks, use

soapy water or liquid soap applied to

each of the connections. Any

bubbles formed indicate a leak.

Correct all leaks immediately.

IMPORTANT: The gas hose and

cylinder must ALWAYS be located well

behind the heater.

WARNING: PROPANE GAS CYLINDERS MUST BE USED AND STORED IN

ACCORDANCE WITH THE HIGHLY FLAMMABLE LIQUIDS AND LIQUEFIED

PETROLEUM GASES REGULATIONS 1972’

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

In order to reduce the risk of icing up

when operating at long periods at

maximum capacity, you should use a

larger capacity gas bottle, or two/

three bottles in parallel, as shown in

Fig 2.

• The ‘Tee’ piece and ‘pigtails’

are readily available from your

builders merchants or gas

supplier.

CHANGING GAS BOTTLES

1. Turn off the heater and disconnect from the electrical supply.

2. Close the gas valve on the bottle and unscrew the regulator, (left hand

thread).

3. Ensure the replacement bottle screw threads and gas orifice is perfectly

clean before screwing in the regulator valve tightly.

4. Check to ensure there are no leaks using soapy water and when satisfied,

plug in to the electrical supply and restart the heater.

OPERATING SPACE AND AIR SUPPLY

MINIMUM FRESH AIR OPENING REQUIREMENTS

As a general rule of thumb, an opening of 1in2per 1000 Btu/hr is a minimum

requirement.

These heaters are specified as requiring a minimum ventilation of 3 sq/ ft per

100,000BTU/hr.

OPERATING SPACE

Do not obstruct the air intake to the heater and allow 4 feet (125cm) between

rear, top and sides and walls or other obstructions.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PRINCIPLE OF OPERATION

Understanding the basic operation of the heater will reinforce the need to

maintain the unit in top condition at all times, whilst always observing the

safety precautions.

The heater comprises four basic systems:

1. The gas system.

2. The air system.

3. The ignition system.

4. The safety control system.

AIR SYSTEM

An axial fan, which is energised when switching on, provides the air flow

through the combustion chamber to provide a stream of hot air from the

heater.

GAS SYSTEM

The gas supply to the machine is by means of a high pressure hose,

connected to an LPG (Liquid Propane Gas) cylinder, via a pressure regulator.

When the mains supply is switched on, the Safety Shut-off valve solenoid is

energised, allowing the gas to flow to the Flame Failure valve, and when the

failure valve override knob is depressed, gas flows to the burner head.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

IGNITION SYSTEM

Ignition is automatic with this heater as soon as the gas valve button is

depressed, with a continuous spark from the spark plug igniting the gas. As the

thermocouple heats up, a low voltage is fed to the Flame Failure valve,

causing the valve to open, so that after a few seconds, the gas valve button

may be released and the flame is established.

SAFETY CONTROL SYSTEM

Should the flame extinguish for any reason, the thermocouple will quickly cool,

causing the Flame Failure valve to close, shutting off the gas supply.

Similarly, should there be a power failure, causing the fan motor to stop, the

Safety Shut-Off valve solenoid will become de-energised, and therefore shut

off the gas supply.

Additionally, the machine is equipped with thermal overload protection,

which will intervene should the unit overheat, shutting off the electrical supply.

STARTING PROCEDURE

1. Ensure there is sufficient gas and that it is correctly connected.

2. Open the supply valve on the gas

cylinder, and fully open the

regulator valve adjacent to the

gas inlet pipe.

3. Plug the heater in to a suitable

power supply.

4. Set the flame intensity control

valve (B), to a low setting,

5. Set the fan switch (A) to the ON (I)

position. Confirm the fan

operates.

6. Hold in the gas valve button (C), until the thermocouple is energised and

the heater ignites.

7. If the heater fails to ignite, there may be air in the hose so keep the fuel

valve open and wait for about 15 seconds. Wait 30 seconds for unburned

fuel to exit the heater. Repeat the step above.

WARNING: BEFORE STARTING THE HEATER, YOU MUST ENSURE THAT THE

MINIMUM VENTILATION REQUIREMENTS ARE OBSERVED TO AVOID THE

RISK OF CARBON MONOXIDE POISONING.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

8. When the burner remains lit, set the heater at the required level by turning

the flame intensity control valve counter-clockwise. If the burner goes out,

turn off the gas. Turn the gas valve fully clockwise to its lowest position.

Check the fuel supply. If adequate fuel is available, re-start the heater from

step 1.

Should the flame extinguish when the ignition button is released, wait for 1

minute, before repeating the operation.

• Turning the flame intensity control valve anti-clockwise will increase the

gas supply and therefore the output, clockwise to decrease.

If ignition is difficult or irregular, ensure the fan is operating and that the air inlet

and outlet are completely clear. Also ensure that the electrode gap is correct,

and that the electrode is clean (see Maintenance).

IMPORTANT:

Should the thermal overload protection feature operate and the spark plug is

seen to be operating, shut off the gas supply and allow the unit to cool for at

least 10 minutes with the fan running, before attempting to relight the burner.

Should the flame safety valve operate, the heater may be restarted once the

cause of the problem has been found and rectified.

SHUT-DOWN PROCEDURE

1. Turn off the gas at the propane cylinder valve(s).

2. Let the heater run while any gas left in the supply hoses is burnt off.

3. Allow the fan to run for 2 - 3 minutes with the burner off, in order to allow

the casing to cool down and the fan to disperse any residual gas.

4. Switch off the fan and unplug from the electrical supply.

5. Disconnect the gas supply.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Riscaldatore a gas

Clarke

Clarke Little Devil ss Manuale di installazione e funzionamento

Clarke

Clarke 900DV Manuale utente

Clarke

Clarke Little Devil Manuale di installazione e funzionamento

Clarke

Clarke Little Devil (inc ss) Manuale di installazione e funzionamento

Clarke

Clarke MGH1 Manuale di installazione e funzionamento

Clarke

Clarke MGH2 Manuale utente

Clarke

Clarke GRH35 Manuale di istruzioni

Clarke

Clarke Devil 3000 Manuale di istruzioni

Clarke

Clarke GRH35 Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 4000 Manuale di istruzioni

Clarke

Clarke DEVIL 4000 Manuale di istruzioni

Clarke

Clarke 900DV Manuale utente

Clarke

Clarke Little Devil II (inc ss) Manuale di istruzioni

Clarke

Clarke GRH125 Manuale di installazione e funzionamento

Manuali Riscaldatore a gas popolari di altre marche

Superior

Superior BGE18NV Manuale utente

Dru

Dru Room-sealed atmospheric gas-fired heating... Manuale utente

klover

klover TKR 35 Manuale utente

Rothenberger Industrial

Rothenberger Industrial 035984 Manuale utente

New Buck Corporation

New Buck Corporation 34 Manuale utente

Hargrove

Hargrove Timberland Glow Guida rapida

Kinder

Kinder Cameo BF Manuale utente

Qlima

Qlima GH 438 B-2 Manuale

Desa

Desa 125-R Manuale utente

Gasmate

Gasmate AH100 Series Manuale utente

Medallion

Medallion MBP20TLB Guida rapida

Superior

Superior BGE18NR Manuale utente

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Istruzioni per l'installazione

L.B. White

L.B. White Therma Grow HW220 Manuale

Sealey

Sealey LP35.V5 Manuale utente

Italkero

Italkero Falo Evo Manuale utente

Desa

Desa 30LP Manuale utente

Williams

Williams 2509822A Manuale utente