Clarke CMS210S Manuale di istruzioni
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0817 - ISS 2
210MM (8”) MITRE SAW
MODEL NO: CMS210S
PART NO: 6501325
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE 210mm (8”) Mitre Saw.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
IMPORTANT
Please read all of the safety and operating instructions carefully before using this
product. Please pay particular attention to all sections of this User Guide that
display warning symbols and notices.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
WARNING: THIS IS A WARNING SYMBOL. THIS SYMBOL IS USED
THROUGHOUT THE USER GUIDE WHENEVER THERE IS A RISK OF
PERSONAL INJURY. ENSURE THAT THESE WARNINGS ARE READ AND
UNDERSTOOD AT ALL TIMES.
CAUTION: THIS IS A CAUTION SYMBOL. THIS SYMBOL IS USED
THROUGHOUT THE USER GUIDE WHENEVER THERE IS A RISK OF
DAMAGING YOUR PRODUCT. ENSURE THAT THESE CAUTIONS ARE
READ AND UNDERSTOOD AT ALL TIMES.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CABLE SAFETY RULES
WORK AREA
1. Keep the work area clean and
well lit. Cluttered and dark areas
invite accidents.
2. Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable
liquids, gases or dust. Power tools
create sparks which may ignite
the dust or fumes.
3. Keep children and bystanders
away while operating a power
tool. Distractions can cause you
to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use adapter
plugs with earthed (grounded)
power tools. Unmodified plugs
and matching outlets will reduce
the risk of electric shock.
2. Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk
of electric shock.
3. Do not abuse the cable. Never
use the cable for carrying, pulling
or unplugging the power tool.
Keep the cable away from heat,
oil, sharp edges or moving parts.
Damaged or entangled cables
increase the risk of electric shock.
4. When operating a power tool
outdoors, use an extension cable
suitable for outdoor use. Use of a
cable suitable for outdoor use
reduces the risk of electric shock.
5. If operating the power tool in a
damp location is unavoidable,
use a residual current device
(RCD) protected supply.
PERSONAL SAFETY
1. Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
moment of inattention while
operating power tools may result
in personal injury.
2. Use safety equipment. Always
wear eye protection. Safety
equipment such as dust mask,
non-skid safety shoes, hard hat, or
hearing protection used for
appropriate conditions will
reduce personal injuries.
3. Avoid accidental starting. Ensure
the switch is in the off position
before plugging in. Carrying
power tools with your finger on
the switch or plugging in power
tools that have the switch on
invites accidents.
4. Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
5. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected
situations.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
GENERAL SAFETY RULES
6. Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewellery or long hair can be
caught in moving parts.
7. A laser beam can cause serious
eye injury. Never look into the
laser outlet.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use
the correct power tool for your
application. The correct power
tool will do the job better and
safer at the rate which it was
designed.
2. Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be
controlled with the switch is
dangerous and must be repaired.
3. Disconnect the plug from the
power source before making any
adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk of
starting the power tool
accidentally.
4. Store idle tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are
dangerous in the hands of
untrained users.
5. Maintain power tools. Check for
misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tools operation.
If damaged, have the power tool
repaired before use. Many
accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and
clean. Tools with sharp cutting
edges are less likely to bind and
are easier to control.
7. Use the power tool and
accessories in accableance with
these instructions and in the
manner intended, taking into
account the working conditions
and the work to be performed.
Use of the power tool for
operations different from
intended use could result in a
hazardous situation.
ADDITIONAL SAFETY
RULES FOR MITRE SAWS
1. Make sure all locking knobs and
clamp handles are tight before
starting any operation.
2. Do not operate the machine
without the guard in position, or if
the guard does not function
correctly or is not maintained
properly.
3. Never use your saw without the
kerf plate.
4. Never place either hand in the
blade area when the saw is
connected to the electrical
power source.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ADDITIONAL SAFETY RULES FOR MITRE SAWS
5. Never attempt to stop a machine
in motion rapidly by jamming
anything against the blade; injury
can result.
6. Before using any accessory
consult the instruction manual.
The improper use of an accessory
can cause damage.
7. Observe the maximum speed
marked on the saw blade.
8. Always wear gloves when
handling a saw blade.
9. Do not use blades of larger or
smaller diameter than
recommended. For the proper
blade rating refer to the technical
data. Use only the blades
specified in the specifications
section of this manual.
10. Do not use cracked or damaged
saw blades.
11. Do not use any abrasive discs.
12. Raise the blade from the kerf in
the workpiece prior to releasing
the switch.
13. Ensure that the arm is securely
fixed when performing bevel cuts.
14. The blade guard on your saw will
automatically raise when the arm
is brought down; it will lower over
the blade when the arm is raised.
The guard can be raised by hand
when installing or removing saw
blades or for inspection of the
saw. Never raise the blade guard
manually unless the saw is
switched off.
15. Keep the surrounding area of the
machine well maintained and
free of loose materials, e.g. chips
and cut-offs.
16. Before use, check that the motor
air slots are clean and free of dust
and woodchips.
17. Replace the kerf plate when
worn.
18. Disconnect the machine from the
mains before carrying out any
maintenance work or when
changing the blade.
19. Never perform any cleaning or
maintenance work when the
machine is still running and the
head is not in the rest position.
20. When possible, always mount the
machine onto a bench or
plywood base which is then
clamped to a bench, or mount
the machine to a purpose built
mitre saw stand available from
your local Clarke dealer.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY SYMBOLS
Wear eye protection
Wear dust mask
Wear ear defenders
Do not put your hand near the blade
Read instruction manual before use
Laser Radiation, Class 2 Laser: Do not stare
into the beam.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug,
for connection to a standard, domestic electrical supply. Should the plug
need changing at any time, ensure that a plug of identical specification is
used.
If the colours of the wires in the power cable of this product do not correspond
with the markings on the terminals of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal
which is marked Nor coloured Black.
• The wire which is coloured Brown must be connected to the terminal
which is marked Lor coloured Red.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
This symbol indicates that this is a Class II product, and does not require
an earth connection.
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCABLEANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue) Live
(Brown)
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
OVERVIEW
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
BEFORE USE
1. Remove the saw from the packing material carefully.
• The following should be supplied. If anything is missing contact your
dealer.
BENCH MOUNTING
Holes are provided in all four feet to
facilitate bench mounting.
• Always mount your saw firmly
on a level surface to prevent
movement.
The saw can also be mounted to a
piece of 12.5 mm or thicker plywood
which can then be clamped to your
bench or moved to other job sites
and re-clamped when required.
• When mounting your saw to a piece of plywood, make sure that the
mounting screws do not protrude from the underside of the wood.
• If the saw rocks on the mounting surface, place a thin piece of material
under one foot until the saw is stable.
MITRE SAW STAND (NOT SUPPLIED)
You can also mount the machine to
a purpose built mitre saw stand
available from your local Clarke
dealer.
This highly versatile, folding stand
includes extendable workpiece
supports and is great for onsite use
and when cutting longer workpieces
210 mm Sliding Mitre Saw with Laser Guide 24 tooth TCT Blade (fitted)
Work Clamp Assembly Dust Collection Bag
2 x Work Supports 2 x Hexagon Key; 4 mm + 6 mm
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
LOCKING / RELEASING THE SAW HEAD
1. Press down slightly on the
operating handle and pull out the
head lock pin.
2. Gently release the downward
pressure on the operating handle
and allow the head to rise to its full
height.
FITTING THE WORK CLAMP
1. Loosen the thumb screw on the
clamp support.
2. Slide the work clamp into the
clamp support.
3. Tighten the thumb screw to
secure the work clamp.
4. Adjust the clamp as required.
FITTING WORK SUPPORTS
1. Loosen the support locking bolt.
2. Slide the work supports into place
(at each end of the cutting bed)
as shown.
3. Secure in place by tightening the
support locking bolts.
DUST EXTRACTION
This machine is provided with a dust
extraction point for connection to a
dust bag (supplied).
1. Place the dust bag over the dust
extraction port using the clip on
the neck of the dust bag.
2. Make sure the zipper on the dust
bag is closed.
3. The dust extraction port may also be connected to a suitable extraction
system, using the appropriate hose (not supplied).
• Dust Extraction Port diameter: (Inner 35mm / Outer 45 mm).
Indice
Altri manuali Clarke Sega
Clarke
Clarke Woodworker CTS10D Manuale di installazione e funzionamento
Clarke
Clarke CCO14C Manuale di istruzioni
Clarke
Clarke CBS 190 Manuale di installazione e funzionamento
Clarke
Clarke CAT118 Manuale di installazione e funzionamento
Clarke
Clarke WOODWORKER CTS800B Manuale di installazione e funzionamento
Clarke
Clarke Contractor CCS2 Manuale di installazione e funzionamento
Clarke
Clarke CSS16V Manuale di installazione e funzionamento
Clarke
Clarke CTS16 Manuale di installazione e funzionamento
Clarke
Clarke CONTRACTOR CON185B Manuale di istruzioni
Clarke
Clarke CBS300 Manuale di istruzioni
Clarke
Clarke CMS250S Manuale di istruzioni
Clarke
Clarke woodworker CMS10 6501305 Manuale di installazione e funzionamento
Clarke
Clarke Woodworker CMS251 Manuale di installazione e funzionamento
Clarke
Clarke CCO14 Manuale di installazione e funzionamento
Clarke
Clarke MBS600D Manuale utente
Clarke
Clarke CSS16VB Manuale di istruzioni
Clarke
Clarke CMS210 Manuale di istruzioni
Clarke
Clarke WOODWORKER CBS205 Manuale di istruzioni
Clarke
Clarke WOODWORKER CCS12B Manuale di istruzioni
Clarke
Clarke CAT32B Manuale di istruzioni
