Clarke MBS600D Manuale utente

ASSEMBLY INSTRUCTIONS

GC05/12

600mm COMPOUND MITRE SAW

MODEL NO: MBS600D

Part No: 6461516

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Mitre Saw.

Before attempting to use the product, it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will

ensure the safety of yourself and that of others around you, and you can also

look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a re-cycling centre

and disposed of appropriately.

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

COMPONENT GUIDE

Upon receipt of the product, unpack all loose components and check for

any missing parts. Any identified should be reported to your Clarke dealer.

The MBS600D includes the following:

1 x Saw Table with wooden base

1 x 600 mm Saw mounted in Saw Frame

4 x Support Rods

2 x Polymer Guide Pieces

1 x Work Stop

1 x Work Retaining Clamp

2 x Allen (Hexagonal) Keys

2 x Depth Stop Collars

1 x Work Clamp Securing Knob

1 x Work Stop Securing Knob

DEPTH STOP

COLLAR

WORK CLAMP

WORK STOP

QUADRANT

RELEASE LEVER

SUPPORT RODS

WITH GUIDE PIECES

SAW BLADE

BLADE

TENSIONER

MITRE ANGLE CARRIAGE

HORIZONTAL QUADRANT

VERTICAL

QUADRANT

SAW TABLE

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

ASSEMBLY

GUIDE RODS, SAW FRAME AND BLADE

1. Attach the handle to the upright

part of the saw frame using the

two screws, with the nuts seated in

the handle moulding.

2. Connect the polymer guide

pieces to the saw frame assembly

as shown in Fig 1.

2. Insert the guide support rods

through the holes in each guide

piece as shown in Fig 2, noting

that two of the rods include a

small end stop. This must remain at

the top of the guide rod.

3. Slide a depth stop collar onto one

front and one rear guide rod from

below and lock in position with

the thumbscrew.

4. Lift the saw frame, complete with

guide rods, and place the guide

rods into their respective sockets

in the mitre angle carriage.

5. Tighten the grub screw for each

socket using a hexagonal key to

secure the saw frame/guide rod

assembly in place.

FIG 1

FIG 2

END STOP

DEPTH STOP

COLLAR

FIG 3

SOCKETS

WITH GRUB

SCREWS

FRAME

UPRIGHT

FIXING SCREWS

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

6. With the saw frame assembly in

position, tension the blade using

the wing nut, until any sideways

deflection of the blade is minimal.

• This is essential to ensure a straight

and repeatable cut from the

blade.

• The saw blade can be removed

for replacement by loosening the

wing nut fully and disengaging

the blade from its mounting pegs

at each end of the frame.

WORK CLAMP

1. Pass the threaded shaft of the

work clamp into one of the holes

in the front face of the saw table,

(see fig 5), depending upon

which end of the table your work

is to be mounted.

2. Screw on the retaining nut to

keep it in place.

WORK- STOP

1. Screw the stop rod adjusting knob

into the threaded hole at one end of the saw table depending upon

which side of the saw blade your work is to be mounted.

2. Slide the work stop rod through the base until it emerges from the hole in

the opposite end. Set it in the position required, by tightening the thumb-

screw.

• Your saw is now fully assembled and ready for use.

BENCH MOUNTING

You may wish to install the saw on a firm foundation such as a workbench or

work table. This is particularly advisable if you are cutting larger workpieces.

Use the holes in the wooden base plate for this purpose, securing with bolts,

flat washers and wing nuts for quick and easy removal, if required (not

supplied).

TENSIONING WING NUT

FIG 4

FIG 5 WORK

CLAMP

WORK

STOP

ROD

RETAINING NUTS

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

USING THE MITRE SAW

CUTTING SIMPLE MITRES OR BEVELS

Simple mitres or bevels are cuts made in one plane only. For simple mitres, the

carriage is moved to the desired angle to the base by pulling the horizontal

quadrant release lever to allow the carriage to swivel, with the saw blade

remaining perpendicular to the table.

Setting the carriage to the angles shown in Fig 6, will produce the mitres

illustrated. The angle is shown by the pointer.

COMPOUND MITRES

For compound mitres the saw frame

is tilted over at an angle to the table.

This is done by releasing the large

socket bolt in each end of the mitre

carriage sufficiently to free the

vertical quadrant and to allow the

saw frame to be tilted to the desired

angle. The socket bolt is then

tightened when the saw frame is set

at the desired angle.

Compound mitres are therefore cut

using a combination of these

settings.

CUTTING TECHNIQUE

When cutting, DO NOT force the saw blade, as this will lead to blade

distortion and inaccurate mitres/bevels. Only a very gentle pressure is

required. Let the saw do the work.

Ensure the socket screws at both ends of the carriage are tight before use.

FIG 6

FIG 7

SOCKET

BOLT

VERTICAL

QUADRANT

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

Always clamp the workpiece to the saw table before work.

Ensure the saw blade is correctly tensioned before use - too slack will allow

the blade to twist, producing inaccurate mitres. Take care never to use

damaged saw blades. Release the blade tension if the saw is not to be used

again for some time.

Use the depth stop collars as required when making either a horizontal or

sloping cut. Tighten them securely with the thumb-screws before cutting.

Replacement blades are available from your CLARKE dealer;

Part No: 6470175

SPECIFICATIONS

erutaeF noitacificepS

htgneLxhtdiWesaBmm002xmm084

)emarfwas(htpeDmm537

htgneLedalBwaSmm006

htpeDedalBwaSmm54

thgieWgk8.

tuCfohtpeDxaMmm051

09@tuCfohtdiWxaM

mm071

hcnIrephteeTipt91

Please note that the details and specifications contained herein, are correct at the

time of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice.

Indice

Altri manuali Clarke Sega

Clarke

Clarke WOODWORKER CBS250 Manuale

Clarke

Clarke WoodWorker CCS1 Manuale di installazione e funzionamento

Clarke

Clarke CMS255S Manuale di istruzioni

Clarke

Clarke Woodworker CBS12WC Manuale di installazione e funzionamento

Clarke

Clarke CCS305 Manuale di installazione e funzionamento

Clarke

Clarke CTS16 Manuale di installazione e funzionamento

Clarke

Clarke CAT118 Manuale di istruzioni

Clarke

Clarke CSS400D Manuale di istruzioni

Clarke

Clarke Woodworker CSS400B Manuale

Clarke

Clarke CTS11 Manuale di installazione e funzionamento

Clarke

Clarke Contractor CON185 Manuale di istruzioni

Clarke

Clarke CONTRACTOR CON850B Manuale di istruzioni

Clarke

Clarke CMS210 Manuale di istruzioni

Clarke

Clarke CRS350M Manuale di istruzioni

Clarke

Clarke WOODWORKER CBS250 Manuale di installazione e funzionamento

Clarke

Clarke CTS800C Manuale di istruzioni

Clarke

Clarke Woodworker CTS10D Manuale di installazione e funzionamento

Clarke

Clarke CMSF110 Manuale di installazione e funzionamento

Clarke

Clarke CAT32B Manuale di istruzioni

Clarke

Clarke CCS185 Manuale di istruzioni

Clarke

Clarke CPMCS1 Manuale di istruzioni

Clarke

Clarke contractor CON100 Manuale di installazione e funzionamento

Clarke

Clarke CRS710B Manuale di istruzioni

Clarke

Clarke CLS400 Manuale di installazione e funzionamento

Manuali Sega popolari di altre marche

RIDGID

RIDGID BS1400 Manuale utente

ATIKA

ATIKA BWS 400-2 Manuale utente

RGC

RGC FS20 Manuale utente

Makita

Makita M2300 Manuale utente

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuale utente

IMET Spa

IMET Spa SIRIO 370 AF-E Manuale utente

Optimum

Optimum OPTisaw CS 275 Manuale utente

Makita

Makita BPB180 Manuale utente

Stihl

Stihl MS 462 C-M Manuale utente

AEG

AEG TS 250 K Manuale utente

Meec tools

Meec tools 004665 Manuale utente

Makita

Makita LS1018L Manuale utente

Ryobi

Ryobi RCS1400 Manuale utente

DeWalt

DeWalt DCS391 Manuale utente

Sealey

Sealey SA72 Manuale utente

skilsaw

skilsaw SPT88 Istruzioni per il montaggio

Urrea

Urrea SI810 Dimensioni e guida di installazione

EINHELL

EINHELL BKG 210/1 Manuale utente