Classe Audio C-303 Manuale utente

CLASSÉ AUDIO

C-303

REMOTE CONTROL

BALANCED LINE PREAMPLIFIER

C-303

OWNER'S MANUAL

C-303 Issue 1 July ‘98

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a

live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:

All Classé products (all preamps and all amps) share exactly the same circuit design philosophy

(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high

level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to

different power levels etc. Differences between less expensive models and more expensive models

are parts quality and compliment, power supply extravagance and the amount of filtering etc., as

well as features and packaging.

This means that for years Classé has been constantly sonically fine tuning and technically upgrading

this circuit design and its application, thus reaching a very high level of natural musical enjoyment,

as well as excellent reliability which benefits all models - least expensive, most expensive, preamps

and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provides Classé owners with years of proven trouble free reliability and

musical enjoyment.

C-303 Issue 1 July ‘98

C-303

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP..…............................................. 4

A.C. LINE POWER.............................................................. 5

INPUTS................................................................................. 6

OUTPUTS ............................................................................ 9

FRONT PANEL CONTROLS…………………………... 10

REMOTE HANDSET ………………………………….. 12

FEATURES AND SPECIFICATIONS ……...................... 20

C-303 Issue 1 July ‘98

UNPACKING & SET-UP

Your CLASSÉ C-303 preamplifier has been carefully wrapped in heavy gauge plastic, packed in

semi-rigid foam and contained in a special box. To remove the unit, open and spread the top flaps of the

box. By its sides, lift out the entire unit with foam pieces intact. Remove each foam side by pulling

straight out. Remove the plastic wrap and inspect the unit for any concealed damage. Apart from this

owner's manual, please ensure the following has also been included:

1) DETACHABLE LINECORD.

2) ALLEN KEY FOR TOP COVER.

3) REMOTE CONTROL UNIT (Allen key and Batteries: AAA x 2 included).

Please report any damage or missing parts to your dealer promptly.

This preamplifier, being capable of very high gain, must be located in a position free of any

hum-inducing magnetic fields. (This also applies to turntables and interconnect cables.) Positions

adjacent to power amplifiers, A.C line filters, or regulation devices should be avoided. Ideally, a few feet

should separate the preamplifier from the power amplifier. As well, keep low-level interconnect cables

away from the power amp and separate from A.C. linecords.

Heat generated by the preamplifier is negligible. Air space around the unit need not be a

concern.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

Regardless of voltage, the internal fuse rating should be 2 AMP SLO-BLO.

C-303 Issue 1 July ‘98

A.C. LINE POWER

The Classé C-303 preamplifier has a POWER SWITCH located at the back of the unit directly

to the right of the AC cord receptacle, this permits you to turn on (see SAFETY FEATURE below) or

shut down the unit completely. The Classé C-303 also has a STANDBY BUTTON located on the left

side of the front panel which permits you to partially shut down the unit while keeping warmed up parts

of the circuitry .In fact, while thoroughly musical shortly after turn-on, the preamplifier will exhibit

"sonic growth" during its first 300 hours of use.

For optimum sonic performance, you should consider the use of the optional CLASSÉ REFERENCE

A.C. LINECORD. Consult your dealer regarding this accessory.

SAFETY FEATURE:

The C-303 preamplifier is designed with an auto-muting circuit which engages during the initial

7 seconds count down and is indicated by the flashing GREEN STANDBY LED when the unit is first

powered up, or after an AC power failure if the power switch was on. After the 7 seconds countdown,

the STANDBY LED to the left of the front panel will be GREEN thus showing that the unit is in

STANDBY mode. This feature will prevent any turn-on surges or unstable output from reaching the

power amplifier and possibly the loudspeakers. Similarly, make sure the STANDBY is ON (SHOWING

GREEN) and then turn the POWER SWITCH OFF when removing A.C. line power.

CAUTION:

DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE GROUND” OR DEFEATING THE GROUND ON A

3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL INTERCONNECT CABLES BETWEEN THE ELECTRONICS

BEFORE CONNECTING THE A.C LINECORDS TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE

ALSO THE WARRANTY SECTION OF THIS OWNER'S MANUAL.

C-303 Issue 1 July ‘98

INPUTS:

The input jacks are clearly marked on the back of the C-303. The following inputs are provided:

REG 1, REG 2, REG 3, REG 4, BAL 1, BAL 2 and TAPE (see fig. 3, page 14).

REGULAR INPUTS REG 1, REG 2, REG 3, and REG4:

These are all high level inputs sharing exactly the same characteristics, and may be interchanged if

so desired. A tape machine should only be connected to the TAPE input. See TAPE IN and TAPE

OUT below. The REG 1 input could also be fitted with an OPTIONAL PHONO BOARD plug in

module installed in the unit, when this is the case, REG 1 input will show LP on the front panel

display. A ground screw is provided adjacent to the REG 1 input jack.

INSTALLATION OF THE PHONO BOARD

1) Disconnect the A.C. line cord from the wall outlet.

2) Remove the top cover with the supplied Allen key.

3) Locate and replace the two mounting screws (see Fig.5, page 17) with the supplied stand-offs.

4) Remove jumpers J5, J6, J13 and J14 (see fig. 5, page 17). Check if extension sockets are in

place on the reverse side of the phono board.

5) Install and secure the phono board using the screws removed previously in step 3 (see fig. 6, page

18), make sure all the connectors are properly aligned.

6) Set MM/MC jumpers J104, 105, 106, 204, 205, 206, to the desired position. All six of these

jumpers are located at the far right of the phono board (see fig. 6, page 18). Please note that for

ALL HIGH OUTPUT MC Cartridges, the jumpers have to be SET AT MM.

7) Replace the top cover.

C-303 Issue 1 July ‘98

REMOVAL OF THE PHONO BOARD

1) Disconnect the line cord from the wall outlet.

2) Remove the top cover with the supplied Allen key.

3) Remove the screws securing the phono board, remove the phono board and the stand-offs,

replace the screws where the stand-offs were removed (see fig. 5, page 17) to secure the main

board.

4) Replace jumpers J5, J6, J13 and J14 (see fig. 5, page 17) on the main board. Jumpers from the

phono board can be used for that purpose.

5) Replace the top cover.

BALANCED INPUT BAL 1 and BAL 2:

The BALANCED INPUT is a true differential high level input, wired as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

It may be used with CD players that have a balanced output, or any other high level

balanced sources.

TAPE IN

The TAPE IN of the C-303 preamplifier should be connected to the LINE OUT or TAPE

OUT of the tape deck. The TAPE input does not appear on the selector switch. It is activated by the

TAPE switch. (See FRONT PANEL CONTROLS: TAPE BUTTON.)

C-303 Issue 1 July ‘98

IR IN (and OUT)

This will permit you to install an outboard infra-red sensor and therefore be able to control

the C-303 remotely from another room where the outboard IR sensor has been installed. These

connections will be found to the left beside the AC power inlet at the back of the unit (see fig.3, page

15).

C-303 Issue 1 July ‘98

OUTPUTS

The Classé C-303 preamplifier has two (2) regular (single-ended) and one (1) balanced

outputs (see fig. 3, page 15). Both single ended and balanced outputs are working at all times, and

may be used separately, or simultaneously.

TAPE OUTPUT

Whatever input is selected by the INPUT SELECTOR will be fed to the TAPE OUTPUT

jacks. This should be connected to the TAPE IN or LINE IN of the tape deck.

REGULAR OUTPUTS

Simply connect your regular interconnects to the RCA output jacks marks REG OUT 1or

REG OUT 2 on the back of the C-303.

BALANCED OUTPUTS

A balanced power amplifier and balanced interconnects are also required. For use with a

balanced power amplifier other than Classé, the wiring of the 3-pin XLR connectors must be wired

as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

If the pin configuration of the power amplifier differs from above, the balanced interconnects

must be modified to accommodate the different power amp.

Having confirmed the correct connections, plug the XLR connectors of the balanced

interconnects into the locking XLR connector on the rear of the C-303 marked BALANCED

OUTPUT. (To remove the connectors, press the tab above the connector.)

C-303 Issue 1 July ‘98

FRONT PANEL CONTROLS

STANDBY

The Classé C-303 also has a STANDBY BUTTON located on the left side of the front panel which

permits you to partially shut down the unit while keeping warmed up parts of the circuitry .

INPUT SELECTOR:

The input selector (see fig.4, page 16) has two buttons for selecting the inputs; (<) and (>).

Pressing the < button.

selects the input to the left of the currently selected input, and pressing the > button selects the input

to the right of the currently selected input. If the > button is pressed when BAL1 is the current input

then the REG1 input will be selected, and if the < button when REG1 is the current input then the

BAL1 input will be selected. The < and > buttons will select from five input connections on the

preamplifier, but not the TAPE, (see TAPE below).

TAPE

In the SOURCE position (TAPE LED OFF), the preamp will process the signal as chosen by

the INPUT SELECTOR. In the TAPE position (TAPE LED ON (RED)), the preamp will process the

TAPE INPUT signal, overriding the INPUT SELECTOR.

VOLUME CONTROL

The VOLUME CONTROL varies the output level of both channels simultaneously. It can be

operated by remote using the hand held control unit (see fig.4, Page 16) or manually

VOLUME CONTROL (CONTINUED)

Indice

Altri manuali Classe Audio Amplificatore

Classe Audio

Classe Audio CA-2200 - 3 Manuale utente

Classe Audio

Classe Audio DR-10 Manuale utente

Classe Audio

Classe Audio CP-500 - V2.4 Manuale utente

Classe Audio

Classe Audio DR-8 Manuale utente

Classe Audio

Classe Audio CAV-500 Manuale utente

Classe Audio

Classe Audio CA-401 Manuale utente

Classe Audio

Classe Audio CP-65 Manuale utente

Classe Audio

Classe Audio CA-5100 Manuale utente

Classe Audio

Classe Audio CA-2300 Manuale utente

Classe Audio

Classe Audio CAV-180 Manuale utente

Classe Audio

Classe Audio CA-5200 Manuale utente

Classe Audio

Classe Audio CAP-151 Manuale utente

Classe Audio

Classe Audio CA-2300 Manuale utente

Classe Audio

Classe Audio CA-3200 Manuale utente

Classe Audio

Classe Audio CA-2300 - V1.3 Manuale utente

Classe Audio

Classe Audio CA-M300 Manuale utente

Classe Audio

Classe Audio CAV-150 Manuale utente

Classe Audio

Classe Audio CA-2100 Manuale utente

Classe Audio

Classe Audio CA-300 Manuale utente

Classe Audio

Classe Audio CA-150 Manuale utente

Classe Audio

Classe Audio CA-100 Manuale utente

Classe Audio

Classe Audio DR-9 Manuale utente

Classe Audio

Classe Audio 100-A Manuale utente

Classe Audio

Classe Audio CT-5300 - V1.2 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente