Clayton CF700M Guida rapida

This manual includes Installation and

operation instructions for the Model

CF700M Furnace utilizing the listed

operational types:

1. Wood add-on

2. Wood only

Owner’s Installation and Operation Manual

Model CF700M

Installation is to be preformed by a

qualied installer.

SAVE THESE INSTRUCTIONS

This unit is certied UL 391

United States Stove Company

227 Industrial Park Rd.

South Pittsburg, TN 37380 852511-0804F

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certied to comply with the 2016 particulate

emission standards. Not approved for sale after

May 15, 2020

CAUTION:

• The warm air supply outlet of the supplementary furnace shall not be connected to the cold-air return inlet

of the central furnace because a possibility exists of components of the central furnace overheating and

causing the central furnace to operate other than as intended.

• Power source not controlled by furnace main disconnect.

• Respect all local and national codes when installing this unit.

• This unit is not to be connected to a chimney ue serving another appliance.

• This unit is designed to burn solid hardwood only.

40.73

38.39

26.07

1.97

33.63

28.01

40.73

38.39

26.07

1.97

33.63

28.01

Combustible : Wood

Flue Pipe Diameter : 6” (153cm)

Flue Pipe Type: (Standard Single Wall or Double Wall): Black or Blued Steel 2100°F (650°C) Class “A”

Minimum Chimney Height : 12’

Maximum Log Length : 22”

Electrical 120V, 60Hz, 1.8A per blower (5.6A on start up)

Dimensions

Combustion Chamber :

Width x Depth :

18.5” x 22” (469mm x 558mm)

Volume :

Cubic Feet:

3.6 cubic feet

Door Opening : Width x Height: 13.6” x 9.8” (345mm x 248mm)

Pyroceramic Glass Door : (Viewing) Width x Height: 13” x 10.75” (330mm x 273mm)

Weight (lbs): 470

Specications

CONGRATULATIONS!

You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.

By heating with wood you’re helping to CONSERVE ENERGY!

Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least

one tree each year. Future generations will thank you.

This manual describes the installation and operation of the Clayton, CF700M

wood heater. This heater meets the 2017 U.S. Environmental Protection

Agency’s emission limits for wood heaters sold after May 15, 2016. Under

specic EPA test conditions this heater has been shown to deliver heat at a

rate of 20,568 – 64,166 BTU/hr. This heater achieved a particulate emissions

rate of 0.408 lb/mmBtu when tested to method CSA B415.1-10 (*and an overall

efciency of 70.8 %.) The maximum overall heat output of this heater was

tested to be 108,758 Btu/hr.

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

The operation of this wood heater in a manner inconsistent with the owner’s manual will void you warranty and

is also against federal regulations.

This heater is designed to burn natural wood only. Higher efciencies and lower emissions generally result when

burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations to

operate this wood heater in a manner inconsistent with operating instructions in this manual.

0215WS044E

Note: Register your product on line at www.usstove.com. See “Limited Warranty” section for specic warranty

information for your new purchase. Save your receipt with your records for any claims.

Safety

• Do not operate with fuel loading or ash removal doors open.

• Do not connect this unit to a chimney ue serving another appliance.

• Danger: Risk of re or explosion. Do not burn garbage, gasoline, naphtha, motor oil, or other inappropriate

materials. Do not use chemicals or uids to start the re.

• Warning: Risk of re. Do not operate with ue draft exceeding .060” water column/14.93 Pascals. Do not

operate with fuel loading and ash removal doors open. Do not store fuel or other combustible materials

within marked installation clearances. Inspect and clean ues and chimney regularly.

• Caution: Hot surfaces. Keep children away. Do not touch during operation.

• The heat exchanger, ue pipe, and chimney must be cleaned regularly to remove accumulated creosote

and ash. Ensure that the heat exchanger, ue pipe, and chimney are cleaned at the end of the heating

season to minimize corrosion during the summer months. The appliance, ue pipe, and chimney must be

kept in good condition. These instructions also apply to a draft inducer if used. To prevent ame or smoke

spillage, the slide bafe must be pulled out and the fuel loading door left cracked for 10 seconds prior to

opening door fully. Load fuel carefully or damage may result.

• Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

• Do not use chemicals or uids to ignite the re.

• Do not leave the furnace unattended when the door is slightly opened.

• Do not burn garbage, ammable uid such as gasoline, naphtha or motor oil.

• Always close the door after the ignition.

• Consult your municipal building department or re ofcials about permits, restrictions and installations

requirements in your area.

• INSPECT FLUE PIPES, FLUE PIPE JOINTS, AND FLUE PIPE SEALS REGULARLY TO ENSURE THAT SMOKE AND FLUE

GASES ARE NOT DRAWN INTO, AND CIRCULATED BY, THE AIR-CIRCULATION SYSTEM.

• CAUTION: CLEAN OUT OF THE HEAT EXCHANGER, FLUE PIPE CHIMNEY, AND DRAFT INDUCER, IF USED, IS

ESPECIALLY IMPORTANT AT THE END OF THE HEATING SEASON TO MINIMIZE CORROSION DURING THE SUMMER

MONTHS, CAUSED BY ACCUMULATED ASH.

Unpacking And Preassemble

UNPACKING

1. Remove all packaging from the furnace.

2. Remove the supplied tools and parts from the furnace.

A. The supplied ash shovel and poker from the heat exchanger tube, behind the heat exchanger door at

the top of the unit.

BRICK ALIGNMENT

Inspect for any damage. Ensure that the bricks and ash plug are positioned correctly and not broken (see

illustration for proper brick arrangement).

TOOLS AND MATERIALS NEEDED FOR INSTALLATION

The following is a list of tools and materials needed to install your furnace.

• 7/16” socket wrench.

• 5/16” socket (Best if using a power drill and a socket bit).

• Pair of pliers or channel-locks.

• Power drill with an 1/8” drill bit to install sheet metal screws into connector pipe..

• Sheet metal screws.

• Non-combustible oor protector as specied in this manual.

• All chimney and chimney connector components required for your particular venting installation..

• Electrical wiring tools and supplies.

• Ductwork for supply and return air.

Proper Fire Brick Alignment

Furnace Installation

Dimension Inch mm

ABackwall to Furnace 29 737

BSidewall to Furnace 15 381

CSidewall to Flue 18 458

D Backwall to Flue 18 458

ESupply Duct (rst 6 feet) 6 153

F Supply Duct (after rst 6 feet) 1 26

GMinimum Duct height 8 204

INSTALLATION OPTIONS

The installation of this furnace includes supplying electrical power, return (fresh air) ductwork, and supply air

ductwork. This furnace may be installed in two different congurations.

1. Stand alone wood furnace

2. Add-on wood furnace

See kit installation section in this manual to ensure proper assembly, installation and operation of your new

furnace.

If installing in an area with a fan it should not be allowed to create negative pressure in the room where the

furnace is installed.

LOCATING YOUR FURNACE (INSURE THAT THE REQUIRED MAINTENANCE CLEARANCES ARE MAINTAINED)

Your furnace must be installed as shown in this manual and in compliance with all local and national codes.

It is of the utmost importance that the clearances to combustible materials be strictly adhered to during

installation of the furnace. Refer to the table and diagrams below for minimum required clearances.

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

CLEARANCE TO COMBUSTIBLES

MAINTENANCE CLEARANCES

Your furnace has recommended minimum maintenance clearance requirements. These clearances insure that

there is adequate room to preform maintenance and service your furnace. DO NOT store fuel within the specied

clearances. The clearances will change depending on what kits are installed with your furnace. See the tables

and diagram below to determine the clearances for your furnace.

Standard unit (no additional kits)

Dimension Inch mm

HMaintenance Clearance (Front) 24 610

J Maintenance Clearance (Left) 10 254

K Maintenance Clearance (Right) 10 254

L Maintenance Clearance (Rear) 29 737

Unit with Blower Kit

Dimension Inch mm

HMaintenance Clearance (Front) 24 610

J Maintenance Clearance (Left) 24 610

K Maintenance Clearance (Right) 24 610

L Maintenance Clearance (Rear) 36 915

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

MAINTENANCE CLEARANCE

Dimension Inch mm

M* Front 22 558.8

NFlue rear 251

P** Left 8 204

Q** Right 8 204

RFlue Side 251

FLOOR PROTECTOR REQUIREMENTS

FLOOR PROTECTOR

The furnace must be placed on solid concrete, solid masonry, or when installed on a combustible oor, on a oor

protector. The oor protector is required to provide heat, live ember, and ash protection and must be of a non-

combustible, continuous solid surface to protect against inltration of live embers and ash. Floor protection must

have and R-Value of at least 1.03. Refer to oor protector manufacturer’s instructions for installation directions.

The oor protector or non combustible oor must extend under the furnace and beyond each side as shown

below.

Duct Work Installation

We strongly recommend that the hot air ductwork be installed by a home heating specialist. If doing the

installation yourself, before you decide which installation will best suit your needs, consult a qualied heating

technician and follow his recommendations as to the safest and most efcient method of installation.

This furnace can be installed in three ways, as a stand alone unit, parallel, and in series with an existing furnace.

SUPPLY AIR (HOT AIR) PLENUM

The warm-air supply duct shall be constructed of metal in accordance with NFPA 90B, 2-1.1. The plenums installed

to the furnace shall be constructed of metal in accordance with NFPA 90B, 2-1.3.

When installing this furnace the hot air plenum is to have a minimum height of 24” (610mm) if the top of the rst

vertical section is not ush with the top of the rst horizontal section of ductwork. If the top of the plenum is ush

with the top of the rst horizontal section of ductwork then the minium height is 15” (381mm).

RETURN AIR (FRESH AIR)

The return (fresh) air intake on the furnace is on the rear of the unit. The ductwork must be mechanically

attached to the unit or blower kit box with sheet metal screws to ensure a proper operation.

26.25

6.12

Supply Air (Hot Air) Duct Work Outlet Size

Supply Air Plenum Minimum

Height Of 24”

Supply Air Plenum With

Minimum Height Of 15”

STAND ALONE INSTALLATION

If installing this furnace as a stand alone unit, ensure all local codes and all instructions in this manual are followed,

including clearance to combustibles, oor protector specications and safety warnings.

PARALLEL FURNACE INSTALLATION

To install the new furnace in parallel with an existing furnace follow the instructions for series installation with a

few additional requirements listed below.

• The return air will duct directly to the return of the new furnace, and not be pulling through any other

furnace.

• The output of the existing furnace must be equal to or greater than this wood furnace.

• If installing in a parallel conguration the ductwork may need adjustments so as to maintain the static

pressure between 0.2” W.C. And 0.05” W.C.

• A back ow damper must be installed in the supply duct work of the new furnace, to ensure that air does

not circulate back through the wood furnace.

• Some installation congurations may require dampers to be installed in the supply duct work of both

furnaces.

CENTRAL INSTALLATION

ADD-ON INSTALLATION

Indice

Altri manuali Clayton Stufa a legna

Clayton

Clayton 1602R Guida per l'amministratore

Manuali Stufa a legna popolari di altre marche

Plamen

Plamen ECO MINIMAL 50 Manuale utente

Austro Flamm

Austro Flamm KOKO Manuale utente

RAIS

RAIS 800 Manuale utente

Henley

Henley Arklow Manuale utente

Jøtul

Jøtul F 500 Manuale utente

Englander

Englander BLUE RIDGE 100 Manuale utente

WoodPro

WoodPro WS-TS-1500 Manuale utente

Contura

Contura C 586W Manuale utente

Nordpeis

Nordpeis N-20 T Manuale utente

Palazzetti

Palazzetti EVA Guida alla configurazione

Lopi

Lopi 1250 Republic Manuale utente

Panadero

Panadero CAPRI 3V Manuale di programmazione

RAIS

RAIS RONDO 92 Manuale utente

RAIS

RAIS attika NEXO 100 GAS Manuale utente

ADURO

ADURO 15-3 Guida utente

Pacific energy

Pacific energy SUPER 27 SPECTRUM Manuale utente

Avalon

Avalon Olympic 11190 Manuale utente

Ventis

Ventis HES350 Manuale utente