Clearfield FieldSmart Manuale utente

FieldSmart®FxDS Frame

Installation Manual ______________________________________________________

Manual 012010 REV H - July 2018

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxDS Frame

Installation Manual _________________________________________________________

Manual 012010 REV H - July 2018

Table of Contents

Application 3

Description 3

Technical Specications 3

Tools and Optional Materials 4

Packaging 5

Floor Installation 6

Raised Floor Installation 8

FxDS Frame Kit Installation 12

Interbays and End Guards 12

SmartRoute Troughs 13

End Guard Support Bars 14

Doors 15

Adjusting the Doors 16

Grounding 16

Panel Mounting 17

Cable Mounting and Routing 18

Patch and Splice Panels 19

Routing Ribbon Fiber 20

Cable Routing Examples 21

Tie Panels 22

FxDS PON Insert Kit 23

Connector Cleaning Procedure 25

Standard Warranty 28

Proprietary Notice 29

Technical Support 29

FieldSmart®FxDS Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 012010 REV H - July 2018

Application

The FxDS Frame Kit is a fully contained ber management system for the inside

plant. The seven foot seismic frame is provided along with full length front and rear

doors that provide protection for termination elds, incoming distribution cables and

interbay routed jumpers. When used in conjunction with the FxDS panels, ultimate

density and protection is offered at “grow-as-you-go” cost.

Description

The FieldSmart Fiber Crossover Distribution System (FxDS) provides a system of

modular and scalable building blocks to congure a frame system that delivers

industry-leading scalability and ber protection without jeopardizing density or

increasing cost.

The FxDS system easily congures for panel placement and scales simply from 12

ports to a full rack of 1,728 ports as needed. The FieldSmart FxDS requires only

four unique building blocks (SKUs) to congure initial deployment. The user then

adds into the frame whatever is needed as subscriber take rates dictate. The FxDS Frame Kit is an industry standard

7’ x 19” seismic frame that is easily assembled with a set of vertical interbay slack management panels, upper and lower

crossover troughs and a set of removable doors.

SmartRoute Troughing builds upon the cable management functionality with a sleek method of providing a continuous

channel for bay-to-bay routing in a safe and efcient manner without increasing jumper lengths. SmartRoute Troughing

allows the service provider to carry the distance and weight of thousands of jumpers on a horizontal plane. This spreads

the pile up and eliminates the risk of micro and macro bends. When used across multiple frames, up to three continuous

channels are created allowing bay-to-any-bay routing in a safe and efcient manner. Front route troughs are available when

the frame is deployed with a PON Kit or for environments where interbay routes are not anticipated.

Technical Specications

FieldSmart FxDS Frame Kit

Dimensions 7’ H x 36” W x 18” D

Ratings Compliant to Telcordia GR-449

Port Density 1,728 SC or 3,456 LC

Cassette Types Supported Clearview®Blue

Connector Types SC/UPC, SC/APC, LC/UPC, LC/APC, MPO (additional options available upon request)

Cable Types Indoor Riser, Indoor Plenum, Indoor/Outdoor, Outdoor (Riser/Non-Rated), Outdoor Armored (Riser/Non-Rated), FieldShield®

Splice Capacity 12 or 24 splices in each Clearview Cassette

Storage Capacity One meter of 900 μm ber

Cable Entry Compatibility Top and bottom (oor) entry

Caple Entry Clamp Location On-frame cable clamps (Note: On-frame cable clamps included with FxDS Patch Panels)

Recommended Jumper Length Three meters, plus two meters for each additional frame

Material Steel with almond powder coating

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxDS Frame

Installation Manual _________________________________________________________

Manual 012010 REV H - July 2018

Tools and Optional Materials

Tools:

• Sockets (1/2”, 3/4” and 15/16”)

• Ratchet with Extension

• Phillips Screwdriver

• 1/8” Allen Wrench

• Hammer/Rotary Drill

• 5/8” Masonry Drill Bit

• Blowout Air Bulb or Vacuum with Small Diameter Tube

Materials (ordered separately):

Standard Frame:

• Isolation Pad (19” Frame P/N FMA-L1Z-SUB)

Floor Mounting:

• Floor Mounting Kit (P/N 009106)

Raised Floor Mounting:

• Raised Floor Mounting Kit (P/N 011236)

Patch and Splice Panels:

• Radius Limiter Brackets for Buffer Tube Slack Storage

(P/N 010600)

Ribbon Fiber Protection:

• High Density Ribbon Breakout Kit (P/N 010475)

• Ribbon Fanout Kit (P/N FMA-MZZ)

Radius Limiter Bracket

Breakout Kit Fanout Kit

Isolation Pad

FieldSmart®FxDS Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 012010 REV H - July 2018

Packaging

The FxDS Frame Kit will come in a wood packaging

crate (88” long x 28” wide x 29” high).

Open the crate by removing the 6 screws and removing

the lid. The screws are called out by black circles.

Carefully remove the contents. This includes:

One (1) frame and isolation pad, (4) doors, (2) interbays, (2) end guards, a trough kit usually containing (3) troughs,

a grounding bar and miscellaneous hardware for securing the hinges to the doors and end guards as well as for

mounting the frame to the oor.

Note: The FxDS Frame system comes in a variety of congurations so the above bill of materials will vary.

This is what the crate will look like while unpacking. Once you conrm all the parts and hardware are available, it is

time to install the frame.

Note: Floor mounting hardware is NOT included with the standard frame. Hardware is sold as a separate line item

(Cleareld P/N 009106).

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxDS Frame

Installation Manual _________________________________________________________

Manual 012010 REV H - July 2018

Floor Installation

IMPORTANT: If your frame is to be mounted next to a wall, or there are multiple frames in a line-up, you MUST

install the interbay management and end guards (including the female hinge pieces for the end guard support bars)

BEFORE mounting the frame to the oor.

Tools:

• Hammer (or rotary) drill (with depth gauge recommended)

• 5/8” masonry drill bit

• Socket wrench set

• Blowout air bulb or vacuum with small diameter tube

Using a 5/8” masonry bit, drill the four required holes to a

minimum depth of 2” (approx. 50mm).

Note: If for some reason you have trouble drilling the 5/8” hole,

we recommend rst drilling a ¼” pilot hole before drilling out to

5/8”.

Thoroughly clean the dust from each hole, using a vacuum or

blowout air bulb.

Note: To not degrade the anchor’s installed performance, any unused anchor holes (or other nearby holes) in the

concrete within 3” must be lled with an epoxy ller (pour stone) or equivalent. Filled holes must be fully cured before

anchors are installed and torqued.

19” Frame

9 5/8”

22”

1. Determine where the frame is going to be installed. Using the isolation pad as a template, mark the 4 holes where

frame will be secured to the oor.

FieldSmart®FxDS Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 012010 REV H - July 2018

Place the isolation pad in position over the predrilled holes and align as necessary. Lift the frame onto the isolation

pad and line up with holes.

Ensure that the anchor’s expansion shield is not expanded. Place the end of the anchor into the predrilled hole.

Repeat for the other drilled holes. Make sure the anchor is fully embedded in the concrete.

Align the edges of the 2” square washer parallel with the slots in the frame base to obtain the maximum material

overlap. Once aligned, tap each anchor/washer assembly until it is seated rmly in the hole against the 2” square

washer.

Pre-tighten each anchor with a socket wrench or box-end wrench; do not use an open-end wrench (which could easily

slip off and cause injury). Before nal tightening, ensure that the frame is properly aligned (in the row and with any

adjacent frames). Torque each anchor to 60 ft-lbs.

Note: When using the break-off type anchor, a torque wrench is not required. The anchor’s (red) torque cap shears off

at a predetermined torque value (approximately 60 ft-lbs.), leaving a green seal on the bolt head, indicating proper

tightening.

The anchoring line up should look like this:

Note: Square

washers will be

packaged in base

of frames

Threaded Rod

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxDS Frame

Installation Manual _________________________________________________________

Manual 012010 REV H - July 2018

Raised Floor Installation

IMPORTANT: If your frame is to be mounted next to a wall, or there are multiple frames in a line up, you MUST

install the interbay management and end guards (including the female hinge pieces for the end guard support bars)

BEFORE mounting the frame to the oor.

Tools:

• Hammer (or rotary) drill (depth gauge recommended)

• 5/8” masonry drill bit

• Socket wrench set

• Blowout air bulb or vacuum with small diameter tube

Also required is a raised oor mounting kit (Cleareld P/N 011236).

1. 1/2-13 Hex Nut (Qty 8)

2. 1/2 Lock Washer (Qty 4)

3. 1/2 Flat Washer (Qty 4)

4. 1/2-13 x 30 Threaded Rod (Qty 4)

5. Hilti HDI 1/2” Anchor (Qty 4)

6. 1/4 x 2” Flatwasher .515 Hole (Qty 8)

7. Split Tubing 30” (Qty 4)

Screw Sequence for Floor Screw Sequence for Frame

Note: Cleareld recommends installing the anchors directly into the concrete oor.

FieldSmart®FxDS Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 012010 REV H - July 2018

Using the isolation pad as a template, mark on the panel(s) of the raised oor the 4 holes where the frame is going to

be secured to the oor. Using a 5/8” drill bit, drill a hole through each of the oblong marks you made with the isolation

pad.

Take the threaded rods from the raised oor mounting kit and slide one through each of the holes. Using a hammer

and holding them perpendicular to the oor, tap on the end rmly. The goal is to make a “mark” on the concrete oor

visible enough to see where the 4 holes should be drilled.

Once the concrete oor is marked, remove the threaded rods and oor panels. Using a 5/8” masonry bit, drill the four

required holes to a minimum depth of 2” (approx. 50mm).

Note: If for some reason you have trouble drilling the 5/8” hole, we

recommend rst drilling a 1/4” pilot hole before drilling out to 5/8”.

Thoroughly clean the dust from each hole, using a vacuum or blowout

air bulb.

Note: To not degrade the anchor’s installed performance, any unused

anchor holes (or other nearby holes) in the concrete within 3” must be

lled with an epoxy ller (pour stone) or equivalent. Filled holes must be fully cured before anchors are installed and

torqued.

19” Frame

9 5/8”

22”

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxDS Frame

Installation Manual _________________________________________________________

Manual 012010 REV H - July 2018

Install anchors into the oor. Replace raised oor panels and

insert threaded rods through the four holes.

Note: You are not installing the rods at this point. We are

measuring the rods to be cut to the appropriate length.

Measure the rods 2.5” above the oor and mark with a

permanent marker. Remove the rods and cut each rod at the

mark. Remove the oor panels.

Before installing rods back into the oor, place a nut and then

a washer on the threaded rods. Take the rod and install it into

the anchor installed in the oor.

Tighten the nut down to secure the rod into the oor. Tighten

each bolt to 65 ft-lbs., +10, -0 ft-lbs. The anchor will expand

and secure itself to the oor.

Once all four rods are secure, thread another hex nut, then

washer on each rod. Make sure the nut and washer are

approximately ½” below the raised oor level. This hardware

will be tightened down AFTER the frame is set into place but

BEFORE securely bolting the frame to the oor.

Altri manuali per FieldSmart

Indice

Manuali Unità di distribuzione dell'energia popolari di altre marche

hager

hager SP 015 Manuale utente

Pakedge

Pakedge PowerPak 9 Manuale utente

Pts

Pts 9042 Series Manuale utente

Shure

Shure WA405 Manuale utente

CORNING

CORNING CCH 4U Manuale utente

Panamax

Panamax M4LT-EX Manuale utente

PANCONNECT

PANCONNECT FLAT 3M Manuale utente

Raytheon

Raytheon 138-118 Manuale utente

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manuale utente

Botex

Botex PSA 322-6 DL Manuale utente

GE QuiXtra 4000 Guida rapida

RDL

RDL EZ Series Manuale utente

StarTech.com

StarTech.com RKPW161915 Manuale del sistema

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manuale utente

ABB

ABB PSBS0065 Manuale

Baumuller

Baumuller BFN 3-1-0007-001 Manuale

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manuale

GE GEK-45404F Manuale utente