CLEARSONIC IsoPac Manuale utente
IsoPac and Height Extender Assembly Instructions
What you will need: Rubber hammer, rubbing alcohol or PPC cleaner with clean rag to
lube the panel end. A reasonably tall assistant is also great to have.
1. First, check to make sure that nothing was damaged in shipment. If you see damage,
call us as or your dealer soon as possible. Please keep your packing materials as long as
possible for storage and transport. Erect your ClearSonic Panel System according to the
usage instructions included with the panel system.
2. How to install AX12s or AX18s:
A. Your AX panels have been attached together with hinge here at the factory.
Inspect your AX panels and H-channels to make sure they were not damaged
during shipment. The “H” channel sections will be used to attach the AX Height
Extenders to the top of your ClearSonic Panel (CSP) system. Keep the packing
materials in case products need to be returned or for future storage and transport.
B. If possible, set up your large panel system in a “zigzag” configuration with
about 45 degrees of angle from one panel to the next so that it is stable. Next, peel
the masking off your CSP if you have not already done so and install the H-
channel on the top of your CSP panels taking care to line up the edge of the H-
channel with the edge of the CSP panel. Completely seat the H-channel with a
rubber hammer. Next, note the direction of the hinge fold on your CSP unit. Note
that each panel will fold 180 degrees in one direction but only 90 degrees in the
other. You will want to match the AX hinge configuration with that of the panel
system you are attaching to so that the whole unit will still fold "accordion style"
once the AX units are in place.
C. Use the PPC cleaner or alcohol/rag combo to lube and clean the bottom ½ inch
of the AX panels. This will make the surface slippery for a short while and
facilitate assembly. It works best to have an assistant hold and unfold the panels
one at a time as you do the placement and seating of the AX panels.
D. Line up one end and seat the first AX panel into the H-channel. It does not have
to seat the whole way in at this point. As the first AX is put in place, have your
assistant see that next AX panel is lined up over the next panel and starts to seat
correctly.
E. Set each succeeding AX until all are in place. You will want to go back and tap
the AX panels with your rubber hammer to make sure that they are completely
seated. Continued on back >
Page 1
3. Now you and your assistant are ready to move the CSP panel system into place. Use
soft gloves if you have them to avoid fingerprints. Close the system up and walk it to
the center front of the kit. Rough position the panels by opening in both directions and
wrapping around the both sides of the kit. For small adjustments and final placement, we
recommend that you and your assistant get down on your knees and use the cable pass
openings at the bottom of the system for grips to shift the panels left, right, in, or out. The
system will seem a bit unstable until the Lid is dropped on top.
4. Measure the distance between the end panels and extend the telescoping support bar to
the same length. Place the bar end “J” hooks onto top of the end panels of your ClearSonic
Panel system about 5 inches from the back edge. This bar will support the Lid panels in
the back and the front of the CSP system will hold the lid panels in front. Place the
rectangular STC5 Lid section on top towards the center so that the SORBER overhangs
the front panel by an inch or two. The trapezoid-shaped STS5 units go on either side of the
center STC5. We recommend that you leave at least some gaps for air to be introduced. It
could get very hot inside the booth without some air exchange. The fan will help facilitate
the air exchange.
5. Depending on the IsoPac you have, place the free-standing SORBER S5-2, S4-2, or
A5-5 units behind the kit. Place the Velcro pieces on the S1 and S2 units to be stuck to
the CSP. The bottom row of S2 units that are resting on the floor only need Velcro on the
top edges. On the SORBER units placed higher up, we recommend using at least four
Velcro pieces. Place the Velcro about an inch from the side edge and on the top and
bottom edges of the baffles. Peel the paper off the Velcro just before placing the baffle in
the desired location. Have your assistant apply opposing pressure on the outside of the
CSP and press the S1 or S2 firmly to bond Velcro to the CSP. The free-standing models
can be tacked together using the 4" Velcro flaps provided at the top and bottom edge of
each SORBER panel to create a continuous SORBER wall.
6. The quiet 2-speed fan simply clips onto the top of the back S5-2 or STC5.
Please feel free to call us at 330-650-1420 with any questions or comments you might
have and thank you for using ClearSonic products!
Page 2
Indice
