ClearView IPPTZ-EL2MPIR250L30X-E Manuale utente
IPPTZ-EL2MPIR250L30X-E Installation Manual
Version 1.0
i
Table of Contents
1IPPTZ-EL2MPIR250L30X-E INSTALLATION ............................................. 1
1.1 Installation Preparation .........................................................................................................................1
1.2 Initial Setup.............................................................................................................................................1
1.3 Dial Switch Setup (For Analog Speed Dome Only)..........................................................................1
1.3.1 Dial Switch ......................................................................................................................................... 1
1.3.2 Parity Setup ....................................................................................................................................... 2
1.3.3 Baud Rate .......................................................................................................................................... 2
1.4 Reset and SD card Installation (For IP Speed dome only) .............................................................3
1.5 Installation (For Analog and IP Speed Dome Both) .........................................................................3
1.5.1 Overview ............................................................................................................................................ 3
1.5.2 Installation Conditions ...................................................................................................................... 3
1.5.3 Dig holes ............................................................................................................................................ 3
1.5.4 Speed Dome Installation.................................................................................................................. 4
2HANG MOUNT INSTALLATION .........................................................................6
2.1 Installation Components .......................................................................................................................6
2.2 Installation...............................................................................................................................................6
2.2.1 Installation Requirements ................................................................................................................ 6
2.2.2 Installation Steps............................................................................................................................... 6
3CORNER MOUNT BRACKET ..........................................................................10
3.1 Component Installation .......................................................................................................................10
3.2 Installation.............................................................................................................................................10
ii
3.2.1 Installation Requirements .............................................................................................................. 10
3.2.2 Installation Steps............................................................................................................................. 10
4POLE MOUNT BRACKET ................................................................................12
4.1 Installation.............................................................................................................................................12
4.1.1 Installation Requirements .............................................................................................................. 12
4.1.2 Installation Steps............................................................................................................................. 12
5BRACKET DIMENSIONS .................................................................................14
5.1 Wall Mount Bracket .............................................................................................................................14
5.2 Hanging Mount Bracket (Multiple Lengths) .....................................................................................14
5.3 Corner Mount Bracket.........................................................................................................................15
5.4 Pole mount bracket .............................................................................................................................15
6APPENDIX Ⅰ THUNDER PROOF AND SURGE PROTECTION .......................16
7APPENDIX Ⅱ ABOUT RS485 BUS ...................................................................17
7.1 RS485 Bus Main Feature ...................................................................................................................17
7.2 RS485 Bus Transmission Distance ..................................................................................................17
7.3 The Problem in Practical Use ............................................................................................................17
7.4 RS485 Bus FAQ ..................................................................................................................................18
iii
8APPENDIX Ⅲ THE RELATIONSHIP BETWEEN THE 24V AC CABLE
DIAMETER AND THE TRANSMISSION DISTANCE...............................................19
9APPENDIX IV WIRE GAUGE REFERENCE SHEET .......................................20
10 APPENDIX V SAFETY ROPE INSTALLATION ................................................21
iv
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!
v
Important Safeguards and Warnings
Safety Measures
Qualified Engineer Needed
zThe installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
zThe installation engineer or maintenance engineer shall have qualification certificate for work
at height.
zThe installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
zPlease read the installation manual carefully and keep it well for future reference,
zWe are not liable for any problems caused by unauthorized modifications or attempted repair.
Lifting Appliance Requirement
zPlease select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
zThe lifting appliances shall have the enough capacity to reach the installation height.
zThe lifting appliances shall have safe performance.
Precautions
Safety Transportation
zHeavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
zThis series product must use split type package during the transportation.
zWe are not liable for any damage or problem resulting from the integrated package during
the transportation.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
z75 ohm.
zFull cable with copper conductor
vi
z95% knitted copper shield
International Model Max Distance
(Ft\M)
RG59/U 750ft (229m)
RG6/U 1,000ft (305m)
RG11/U 1,500ft (457m)
Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.
When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
Do not try to dismantle or modify the device
zThere is risk of personal injury or device damage resulting from opening the shell.
zPlease contact your local retailer if there is internal setup or maintenance requirement.
zWe are not liable for any problems caused by unauthorized modifications or attempted repair.
Do not allow other object falling into the device
zPlease make sure there is no metal or inflammable, explosive substance in the speed dome.
zThe above mentioned objects in the device may result in fire, short-circuit or damage.
zPlease shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.
zPlease pay attention to the camera. Avoid the sea water or rain to erode the camera.
Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
Installation Environment Requirement
zThis series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
zThis series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
Daily Maintenance
zPlease use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.
zDo not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
vii
zDo not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.
1
1IR INTELLIGENT SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement
zAll installation and operation here should conform to your local electrical safety codes.
zBefore installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
zWe assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain the 4X weight of the speed dome.
1.2 Initial Setup
The default setup is:
zAddress: 1
zBaud rate: 9600
zParity: None.
1.3 Dial Switch Setup (For Analog Speed Dome Only)
1.3.1 Dial Switch
There are two dial switch buttons on the PCB of one side of the speed dome (There are labels.).
You can use them to set speed dome protocol, baud rate, address and etc. See Figure 1-1 . It is
1 when you set the button as ON.
For the protocol dial switch, you can refer to the following sheet. 1 is the lowest bit and the 8 is
the highest bit.
1 2 3 4 5 6 7 8 ON
NC 120ΩParity Baud rate Connect to the 120Ω
Please note the IR speed dome can automatically recognize the DH-SD, PELCO-D. PELCO-
P. Usually you do not need to set the protocol.
2
Figure 1-1
1.3.2 Parity Setup
Please refer to the parity setup sheet for detailed information.
6 7 Parity
OFF OFF NONE
ON OFF EVEN
OFF ON ODD
ON ON NONE
1.3.3 Baud Rate
Please refer to the baud rate sheet for detailed information.
4 5 Baud Rate
OFF OFF 9600bps
ON OFF 4800bps
OFF ON 2400bps
ON ON
1200bps
The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. You
can refer to the following sheet for more information.
Address 1 2 3 4 5 6 7 8
1 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
1. Address and dial switch button label
2. Protocol dial switch button.
3. Address dial switch button.
1
2
3
ON
OFF
Indice
Altri manuali ClearView Telecamera di sicurezza
ClearView
ClearView PTZ Series Manuale utente
ClearView
ClearView IP-007- Guida all'installazione
ClearView
ClearView CA-0581 BP/N Manuale utente
ClearView
ClearView IPD-81A Manuale utente
ClearView
ClearView IP-PTZ-IR-988-IR Manuale utente
ClearView
ClearView MPTZ-2 Manuale utente
ClearView
ClearView WiFi-2MP-BL100 Guida all'installazione
ClearView
ClearView HD2-TD27 Manuale utente
ClearView
ClearView HD4-D200 Manuale utente
ClearView
ClearView ip-73 Manuale utente
