Clek FLLO Schema elettrico
January 2017
Fllo Inflatable Belt
Supplementary Instructions
® Clek and Fllo are registered trademarks of Clek Inc.
For a complete list of Clek Inc. trademarks please visit clekinc.com/trademarks.
Table of Contents
Installing/Removing Rear-Facing Car Seat ............................................................. 1
Installing Rear-Facing Car Seat With Inflatable Vehicle Belt ............................... 1
Removing Rear-Facing Car Seat Installed With Inflatable Vehicle Belt .................. 7
Installing/Removing Forward-Facing Car Seat ........................................................ 8
Installing Forward-Facing Car Seat With Inflatable Vehicle Belt .......................... 8
Removing Forward-Facing Car Seat Installed With Inflatable Vehicle Belt ........... 14
1
WARNING — DEATH or
SERIOUS INJURY can occur
• Use these instructions to replace the “Installing Rear-Facing Car Seat
with Vehicle Belt” section in your car seat manual.
• Not all inflatable vehicle belts are safe for use with this car seat. Contact
Clek Customer Service at 1-866-656-2462 to determine if the inflatable
belts in your vehicle are approved for use with this car seat.
• Always use these supplementary instructions in addition to the instructions
found in your car seat manual. Your car seat manual contains other
important information about the use and installation of this car seat.
• Never use the Rear-Facing Belt Lock-offs when installing this car seat
Rear-Facing using an inflatable vehicle belt.
• This car seat must be held tight at all times by the lap portion of the lap/
shoulder belt.
− Refer to the vehicle owner’s manual for information regarding
car seat installation and inflatable vehicle belt use with a car seat.
Installing Rear-Facing Car Seat With Inflatable Vehicle Belt
2
Step 1
Prepare car seat for Rear-Facing Installation:
• Rotate Recline Foot to Rear-Facing
position by pulling on edge of Recline
Foot and rotating it towards the front of
the seat until it locks in to position, as
shown in Figure 1.
• Remove Seat Cushion and install Anti-
Rebound Bar. See “Installing/Removing
Anti-Rebound Bar” in your car
seat manual.
Step 2
Select a forward-facing vehicle seating
location which has an inflatable vehicle
belt which can be used with this car seat.
Figure 1
lowered recline foot
Raised recline foot
3
Figure 2
Step 3
If the vehicle seat back is adjustable, make
sure the seat back is locked in a more upright
position. Refer to vehicle owner’s manual for
recommended seat back angle. DO NOT
install or use this car seat while the vehicle
seat back is excessively reclined, as shown
in Figure 2.
Step 4
Place car seat Rear-Facing in the vehicle seat
location selected with Rear-Facing Belt Path
toward vehicle seat back and centered in
seating position as shown in Figure 3.
IMPORTANT: Car Seat base must NOT
extend beyond the edge of the vehicle seat
cushion as shown in Figure 4.
Figure 28
Figure 3
Figure 4
4
Step 5
Position the seat so that the Rear-Facing Level
Reference Line appropriate for the child’s
weight is parallel with the ground as shown
in Figure 5.
• If using with an infant under 10 kg (22lb),
position the seat with the more reclined
Reference Line (top line) parallel to
the ground.
• If using with an older child who is over
10 kg (22lb), position the seat with the
more upright Reference Line (bottom line)
parallel to the ground.
Step 6
Route vehicle belt through the Rear-Facing Belt
Path and over both Rear-Facing Belt Lock-offs
and buckle vehicle belt, as shown
in Figure 6.
Position lap portion of inflatable lap/shoulder
belt under both forward Belt Tabs and check
that Crotch Strap is not under the vehicle belt.
Figure 5
Figure 6
5
Figure 7
Step 7
Switch the the lap portion of the lap/shoulder
belt to the automatic locking mode by pulling
the lap portion of the lap/shoulder belt all the
way out by holding the webbing and pulling
upwards, as shown in your vehicle manual.
Step 8
Tighten vehicle belt to secure the car seat
• Press down in center of car seat to
depress the vehicle cushion and pull
down on the lap portion of inflatable
lap/shoulder belt to tighten as shown
in Figure 7.
NOTE: The lap portion of the inflatable lap/
shoulder belt MUST remain tight and not
lengthen when pressure is released from the
seat. If the lap portion of the inflatable lap/
shoulder belt does not remain tight, go back
to Step 7 and refer to your vehicle manual.
6
Step 9
Check for secure installation. Gripping car
seat at top of armrests, pull car seat front
to back and left to right to check for secure
installation as shown in Figure 8. Vehicle
belt MUST stay tight and child restraint
should not move more than 2.5 cm (1 in.)
in any direction.
• If vehicle belt still does not stay tight or
car seat cannot be securely installed,
try a different vehicle seat location or
install using UAS, see “Installing Rear-
Facing Car Seat With UAS” in your car
seat manual.
Step 10
Verify that the Rear-Facing Level Reference
Line appropriate for the child’s weight is
parallel to the ground as shown in Figure 9.
S t ep 11
Install Seat Cushion, see “Removing/Installing
Seat Cushion” in your car seat manual.
Figure 8
Figure 9
7
Step 1
Unbuckle vehicle belt.
• Pressing down in center of car seat to
reduce tension on vehicle belt will make
it easier to unbuckle vehicle belt as
shown in Figure 10.
Step 2
Remove Seat Cushion, see “Removing/
Installing Seat Cushion” in your car
seat manual.
Step 3
Remove vehicle belt from Rear-Facing
Belt Path.
Step 4
Remove this car seat from vehicle.
Step 5
Install Seat Cushion, See “Removing/
Installing Seat Cushion” in your car
seat manual.
Figure 10
Removing Rear-Facing Car Seat
Installed With Inflatable Vehicle Belt
8
Installing Forward-Facing Car Seat With Inflatable Vehicle Belt
WARNING — DEATH or
SERIOUS INJURY can occur
• Vehicle belt must be routed through Forward-Facing Belt Path and
contained in both red Forward-Facing Belt Guides when using car
seat Forward-Facing.
• Use these instructions to replace the “Installing Forward-Facing Car Seat
with Vehicle Belt” section in your car seat manual.
• Not all inflatable vehicle belts are safe for use with this car seat. Contact
Clek Customer Service at 1-866-656-2462 to determine if the inflatable
belts in your vehicle are approved for use with this car seat.
• ALWAYS use these supplementary instructions in addition to the
instructions found in your car seat manual. Your car seat manual contains
other important information about the use and installation of this car seat.
• Forward-Facing Belt Lock-off must be left completely open when installing
with an inflatable vehicle belt.
9
Step 1
Prepare car seat for Forward-Facing
Installation:
• Check that the Recline Foot is in the
Forward-Facing position as shown in
Figure 11. If needed, grasp forward
edge of Recline Foot and rotate towards
the back of the seat, pressing it in to the
recess in the seat bottom.
• If the Anti-Rebound Bar is attached,
remove it now. See “Installing/Removing
Anti-Rebound Bar” in your car
seat manual.
Figure 11
lowered recline foot
Raised recline foot
WARNING — DEATH or
SERIOUS INJURY can occur (continued)
• ALWAYS secure the Top Tether.
• This car seat must be held tight at all times by the lap portion of the
lap/shoulder belt.
− Refer to the vehicle owner’s manual for information regarding
car seat installation and inflatable vehicle belt use with a car seat.
Altri manuali per FLLO
1
Indice
