Climate RENTAL SOLUTIONS MCWS 250 Manuale utente

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

PRODUCT MANUAL

MCWS 250

PORTABLE WATER COOLED AIR

CONDITIONER

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 2

WARNINGS

These instructions should be read by:

The specifying engineer.

The installation engineer.

The user.

The service engineer.

• Failure to follow these instructions may result in risk of personal injury or damage to the

equipment.

• Damage due to a failure to follow these instructions will invalidate the warranty.

• The appliance must be serviced by qualied engineers in compliance with local regulations.

• The appliance must be switched o󰀨 and disconnected from the power supply before any work

is carried out.

• There are no user controls inside the appliance casing. Do not place anything on top of the

appliance.

• An air gap of at least 300mm should be allowed at the front of the unit to ensure a clear air-

ow.

• Do not disconnect the appliance from the supply under load.

• For internal use only. Do not use out of doors.

• Extension cables should be correctly rated for the load,fully unwound and never run through

water or over sharp edges.

• Always transport and store in an upright position.

• The fan motor on the external heat exchanger is electronically controlled and is liable to start

and stop without notice.

• Maximum operating temperature 40 C.

• Minimum operating temperature 10 C.

• This is a class 1 appliance and must be Earthed.

• The system is supplied with a ‘water only’ test charge. To protect the system from corrosion

and frost damage Propylene Glycol must be added prior to use.(See P8) Damage due to the

failure to add Propylene Glycol will invalidate the warranty.

• Serious risk of injury! Do not support the exterior heat exchanger by means of the exible

lines.

• The air-conditioning process produces condensate (water) during operation. This conden-

sate is pumped away from the main unit along a exible clear line within the connecting hose

assembly and is deposited to the outside from the bottom of the exterior heat exchanger.

Care should be taken when positioning the exterior heat exchanger with regard to this.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 3

SYSTEM DESCRIPTION:

• The MCWS250 is a watercooled split portable air conditioning unit. It is connected to a 13 Amp. 230Vac. 50Hz

power supply and comes tted with a fused uk moulded plug.

• It is recommended that the supply to the machine should be protected by a 30mA RCD.

• The system comprises a main indoor cooling unit, an external heat exchanger and a connecting hose assembly.

The indoor cooling unit is tted with an automatic condensate pump as standard.

• The watercooled split system uses water as a medium to remove heat generated during the cooling process to

the external heat exchanger and then to the air. It is therefore important that the external heat exchanger is not

sited in the same area as the main indoor cooling unit. The system has a minimum operating temperature of 10

C and a maximum operating temperature of 40 C and comes tted with a digital thermostat.

• The watercooled split can run up to a maximum of 35M of connection hose. The external heat exchanger should

never be sited more than 5M vertically above the main unit. Protection for the refrigeration system is provided by

automatic high and low pressure safety switches within the machine. The operation of these switches is indicat-

ed by lamps on the fascia panel. (See page 7)

• The appliance is tted with an automatic defrost which will periodically stop the fan on the external heat exchang-

er. This is indicated by the defrost lamp on the fascia panel. During the normal cooling cycle the cooling lamp on

the fascia panel will be illuminated.

INSTALLATION:

Site the main cooling unit and external heat exchanger in the desired locations. Ensure the locking castors

are engaged on the main unit before operation.

1. Connect the main cooling unit to the external heat exchager and connect to the power supply:

The main cooling unit, external heat exchanger and connecting hose assembly are tted with auto-sealing water

connectors to minimise water loss during connection and disconnection. It should be noted that some water loss

will occur. The female water connectors have a sliding ring which must be pulled back to make the connection.

This will snap back into place once the connection has been made.(see page 5) The water connectors are

situated at the rear of the main cooling unit.

• Fit the water connectors to the main unit.

• Fit the electrical connector to the main unit.

• Fit the clear condensate hose into the push-t connector on the main unit. (see page 4&5)

IT SHOULD BE NOTED THAT THE ELECTRICAL CONNECTORS ARE GENDER SPECIFIC AND WILL ONLY

CONNECT TO THE APPROPRIATE FITTINGS. PLEASE CHECK THE CORRECT PLUG IS AT THE CORRECT

END. TO DISCONNECT THE ELECTRICAL CONNECTORS DEPRESS THE GREY LOCKING PIN AND

WITHDRAW THE CONNECTOR.

• Run the connecting hose assembly to the external heat exchanger in as smooth a run as possible, avoiding

kinks and possible restrictions to water ow to a maximum of 35M.

• Fit the water connectors to the external heat exchanger.

• Fit the electrical connector to the external heat exchanger.

• Fit the condensate clear hose to the hose on the external heat exchanger.

MULTIPLE CONNECTION HOSE ASSEMBLIES CAN BE RUN IN SERIES SHOULD THIS BE REQUIRED TO A

MAXIMUM OF 35M. TO AVOID LEAKS CHECK THAT ALL CONNECTIONS ARE FULLY HOME.

• Connect the mains lead to the power supply and check that the power supply lamp is illuminated.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 4

WATER AND ELECTRICAL CONNECTIONS:

Water connectors.

Electrical connector.

Condensate

hose

connector.

Water

connectors.

Electrical

connector.

Push-fit

condensate hose

connector.

External heat

exchanger connection.

Water

connectors.

Electrical

connector.

Condensate hose.

to fit to main

cooling unit.

Water connectors.

Condensate hose

connector.

Electrical

connector.

Main cooling unit

External heat exchang er

Connection hose assembly.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 5

AUTO-SEALING WATER CONNECTORS:

Male connector

1: Pull locking ring back.

2: Push connector fully home.

3: Release the locking ring.

4: Check the connection is secure.

Locking ring

Female connector

OPERATION:

• Turn the fan switch from 0 to 1 to start the fans on the main cooling unit. Set the • fans to the desired speed using

the 3 position rocker switch.

• Turn the Cooling switch from 0 to ‘I’ to start the compressor and water pump. It should be noted that the compres-

sor and pump will not start if the fans are not running. The compressor will not start if the ambient temperature

is below 10 C. The compressor is tted with a start delay timer and will not run for 3 minutes from activation

of the cooling switch. This device is designed to protect the compressor from repeated start/stop cycles. The

compressor delay is activated each time power to the compressor is switched o󰀨, be that at the wall socket, the

rocker switches or the thermostat.

• Set the digital thermostat to the desired temperature (This is the ‘set point’). During normal running the digital

thermostat read-out shows the ambient temperature of the room. (See P6 for setting the digital thermostat)

• The MCWS250 is tted with adjustable cold air louvres. Adjust these to your prefered angle.

• It should be noted that the appliance will start in defrost mode.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 6

SETTING THE DIGITAL THERMOSTAT:

How to see the set point:

• The set point is the minimum temperature the air-conditioner • will operate down to.

• To see the set point push and immediately release the SET key: the display will show the set point value.

• Push and immediately release the SET key or wait for 5 seconds to display the ambient room temperature.

Set key.

Up/ down

keys.

Power key.

(Not used)

Defrost key.

(Not used)

How to change the set point:

• The appliance comes factory set at 10 C.

• Push the SET key for more than 2 seconds to change the set point value.

• The value of the set point will be displayed and the “ C” LED starts blinking.

• To change the set point value push the up or down arrows within 10 seconds. The minimum set point is 10 C.

• To memorise the new set point value push SET key or wait for 10 seconds.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 7

CONTROL PANEL:

Power

supply

lamp.

Fan switch.

3 position fan

speed switch.

Cooling switch

Digital

thermostat.

LAMP FASCIA PANEL:

Cooling mode.

Defrost mode

Low pressure warning

High pressure warning

Cooling mode: This lamp will be illuminated during normal cooling when the compressor is running.

Defrost mode: This lamp will be illuminated during a defrost cycle when the external heat exchanger fan will be

switched o󰀨. The appliance will start in defrost mode before cooling commences.

Low pressure warning: This lamp will be illuminated if there is a loss of refrigerant gas. The machine should not be

operated if this lamp activates. This will automatically shut down the compressor.

High pressure warning: This lamp will be illuminated when the regrigeration system pressure is too high. (see fault

nding). This will automatically shut down the compressor.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 8

ADDING PROPYLENE GLYCOL PRIOR TO FIRST USE:

Ensure the machine is disconnected from the power supply before following this procedure.

Ensure that all local regulations are adhered to when using Propylene Glycol.

The water cooled split has a uid capacity of approximately 20 litres when tted with a single 5M connection hose

assembly.Each extra 5M hose assembly contains approximately 4 litres of water.

It is recommended that a 25% Glycol to 75% water mix is used. This can be increased to 50% when the external heat

exchanger is located in a very cold environment.

Failure to add Glycol could result in costly damage to the machine and will invalidate the warranty.

1. Connect the connection hose assembly to the main cooling unit only.

2. Depress the spring loaded nipple on the male connector at the end on the hose assembly into the base of a

bucket or similar container.

3. Bleed approximately 5 litres of water into the bucket.

4. Remove the ller cap at the rear of the machine and add approximately 5 litres of Propylene Glycol to the tank.

5. Ensure that the tank is not over lled. Over lling can cause excess water to be expelled to the environment

through the condensate pump.

6. The water tank is full when the uid is approximately 100mm below the top of the ller spout.

7. Replace the ller cap. The appliance is now ready for installation and operation.

Spring loaded nipple.

Filler cap.

Male water conn ector.

Rear of main coo ling unit.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 9

MAINTENANCE AND UPKEEP:

Servicing should only be carried out by competent engineers.

1. Regularly check the uid level in the water tank and top up if necessary.

2. Check and clean the evaporator and external heat exchanger coils. Build up of dust and dirt can severly e󰀨ect

the performance of the machine. Clean with compressed air.

3. Regularly inspect the mains cable and plug for signs of damage or wear. Do not operate the machine with a

damaged mains cable.

4. Check that the castors are running freely and that the breaking mechanisms are working correctly.

5. Inspect the connection hose assembly for signs of wear or damage. Replace if necessary.

TROUBLESHOOTING GUIDE:

PROBLEM POSSIBLE CAUSE SOLUTION

Machine fails to operate

Power Failure

Check power on lamp is illuminated.

Check unit is connected to the power supply.

Check plug fuse for failure and correct 13A

rating.

Check Building circuit is not overloaded.

Condensate pump faulty Check condensate pump. Replace if

necessary.

Poor cooling performance.

Cooling not selected Switch cooling on

Thermostat set incorrectly. (Higher than

ambient room temperature) Reset the thermostat. Page6

Coils dirty Clean coils. See Maintenance

Filters dirty. (where tted, optional extra) Clean lters.

Hose connection assembly over 35M Reduce the length of the hose assembly.

Air inlet grills obstructed Remove obstruction.

Water ow restricted

Check the connection hose assembly

forkinks or blockages. Check all water

connections are correctly tted.

Water pump failed Check and replace pump.

High or low pressure switch activated. See below.

Water leaking.

Clogged drain hose to condensate pump. Remove blockage and clean driptray.

Water connections incorrectly tted Check all connections and make good.

External heat exchanger located poorly Move the unit to an area where draining

condensate will not cause a problem.

Damaged water hoses Check all hoses and replace where

necessary.

Compressor stops working. Input voltage too low. Check line voltage.

High or low pressure switch activated. See below

High pressure warning lamp illuminated.

Water tank empty Check tank and rell if necessary.

Ambient room temperature above the

maximum of 40ºC.

Check temperature read-out on the digital

thermostat. Do not run until room cools below

40ºC.

Water ow restricted

Check all water connections and ensure they

are correct.

Check hoses for signs of restrictions and re-

route if necessary.

Water pump failed Check pump and replace.

External heat exchanger fan faulty.

Check electrical connections on the hose

connection assembly. Replace the fan if

necessary.

Low pressure warning lamp illuminated. Refrigerant loss. Contact supplier.

PRODUCT MANUAL MCWS 250 PORTABLE WATER COOLED AIR CONDITIONER

Page 10

MCWS250 MAIN COOLING UNIT. SPARE PARTS:

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Climate RENTAL SOLUTIONS Condizionatore d'aria

Climate RENTAL SOLUTIONS

Climate RENTAL SOLUTIONS WPC-25000 Manuale utente

Climate RENTAL SOLUTIONS

Climate RENTAL SOLUTIONS PA 28 Manuale utente

Climate RENTAL SOLUTIONS

Climate RENTAL SOLUTIONS MCM350 Manuale utente

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Frigidaire

Frigidaire FFRE0533S1E0 Manuale utente

Samsung

Samsung AS09HM3N Manuale utente

Frigidaire

Frigidaire CRA073PU11 Manuale del proprietario

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente