CLIVET WSHN-XEE2 10.2 Manuale utente

M08U40G16-02

13/03/2019

WSHN-XEE2 10.2 - 120.2

Installation and

operating manual

Water cooled heat pump for indoors installation

Dear Customer,

We congratulate you on choosing this product

For many years Clivet has been oering systems that provide maximum comfort, together with high

reliability, efficie y, quality and safety.

The aim of the company is to oer advanced systems, that assure the best comfort, reduce energy

consumption and the installation and maintenance cost for the life cycle of the system.

The purpose of this manual is to provide you with information that is useful from reception of

the equipment, through installation, operational usage and finally disposal so that this advanced

system oers the beat solution.

Yours faithfully.

CLIVET Spa

The data contained in this manual is not binding and may be changed by the manufacturer without

prior notice.

Reproduction, even is part, is FORBIDDEN © Copyright - CLIVET S.p.A. - Feltre (BL) - Italia

WSHN-XEE2 10.2-120.2 3

Index of contents

1 General description 4

2 Reception 6

3 Positioning 9

4 Water connections 10

5 Electrical connections 13

6 Start-up 19

7 Control 27

8 Maintenance 37

9 Accessories 41

10 Decommissioning 47

11 Residual risks 48

12 Technical information 49

13 Dimensional drawings 56

4 WSHN-XEE2 10.2-120.2

1 General description

1.1 Manual

The manual provides correct unit installation, use and maintenance.

Pay particular attention to:

Warning, identifies pa ticularly important operations or information.

Prohibited operations that must not be carried out, that compromise the operating of the unit or may cause damage to persons or things.

• It is advisable to read it carefully so you will save time during operations.

• Follow the written indications so you will not cause damages to things and injuries people.

1.2 Preliminaries

Only qualified personnel can ope ate on the unit, as required by the regulation in force.

1.3 Risk situations

The unit has been designed and created to prevent injures to people.

During designing it is not possible to plane and operate on all risk situation.

Read carefully “Residual risk” section where all situation which may cause damages to things and injuries to people are reported.

Installation, starting, maintenance and repair required specific knowledge; if they are carried out by inexperienced personnel, they may cause

damages to things and injuries people.

1.4 Intended use

Use the unit only:

• for cooling/heating water or a water and glycol mix

• keep to the limits foreseen in the technical schedule and in this manual

The manufacturer accepts no responsibility if the equipment is used for any purpose other than the intended use.

1.5 Installation

Outdoor installation

The positioning, hydraulic system, refrigerating, electrics and the ducting of the air must be determined by the system designer in accordance

with local regulations in force.

Follow local safety regulations.

Verify that the electrical line characteristics are in compliance with data quotes on the unit serial number label.

1.6 Maintenance

Plan periodic inspection and maintenance in order to avoid or reduce repairing costs.

Turn the unit off be ore any operation.

1.7 Modifi ation

All unit modific tions will end the warranty coverage and the manufacturer responsibility.

1.8 Breakdown/Malfuction

Disable the unit immediately in case of breakdown or malfunction.

Contact a certified se vice agent.

Use original spares parts only.

Using the unit in case of breakdown or malfunction:

• voids the warranty

• it may compromise the safety of the unit

• may increase time and repair costs

WSHN-XEE2 10.2-120.2 5

1.9 User training

The installer has to train the user on:

• Start-up/shutdown

• Set points change

• Standby mode

• Maintenance

• What to do / what not to do in case of breakdown

1.10 Data update

Continual product improvements may imply manual data changes.

Visit manufacturer web site for updated data.

1.11 Indications for the User

Keep this manual with the wiring diagram in an accessible place for the operator.

Note the unit data label so you can provide them to the assistance centre in case of intervention (see “Unit identific tion” section).

Provide a unit notebook that allows any interventions carried out on the unit to be noted and tracked making it easier to suitably note the

various interventions and aids the search for any breakdowns.

In case of breakdown or malfunction:

• Immediately deactivate the unit

• Contact a service centre authorized by the manufacturer

The installer must train the user, particularly on:

• Start-up/shutdown

• Set points change

• Standby mode

• Maintenance

• What to do / what not to do in case of breakdown

1.12 Unit indentifi ation

The serial number label is positioned on the unit and allows to indentify all the unit features.

The matriculation plate shows the indications foreseen by the standards, in particular:

• unit type

• serial number (12 characters)

• year of manufacture

• wiring diagram number

• electrical data

• type of refrigerant

• refrigerant charge

• manufacturer logo and address

The matriculation plate must never be removed.

It contains fluo inated greenhouse gases

Type of refrigerant: R410A

1.13 Serial number

It identifies uniquely each uni .

Must be quoted when ordering spare parts.

1.14 Assistance request

Note data from the serial number label and write them in the chart on side, so you will find them easily when neede .

Series

Size

Serial number

Year of manufacture

Electrical wiringdiagram

6 WSHN-XEE2 10.2-120.2

2 Reception

You have to check before accepting the delivery:

• That the unit hasn’t been damaged during transport

• That the materials delivered correspond with that indicated on the transport document comparing the data with the identific tion label

positioned on the packaging.

In case of damage or anomaly:

• Write down on the transport document the damage you found and quote this sentence: “Conditional acceptance clear evidence of

deficiencies/damages du ing transport”

• Contact by fax and registered mail with advice of receipt to supplier and the carrier.

Any disputes must be made within 8 days from the date of the delivery. Complaints after this period are invalid.

2.1 Storage

Observe external packaging instructions.

2.2 Handling

1. Verify unit weight and handling equipment lifting capacity.

2. Identify critical points during handling (disconnected routes, flig ts, steps, doors).

3. Suitably protect the unit to prevent damage.

4. Lifting with balance

5. Lifting with spacer bar

6. Align the barycenter to the lifting point

7. Gradually bring the lifting belts under tension, making sure they are positioned correctly.

8. Before starting the handling, make sure that the unit is stable.

WSHN-XEE2 10.2-120.2 7

2.3 Instructions for disassembly

Only with options: MOBMAG

8 WSHN-XEE2 10.2-120.2

Isolating switch

2.4 Packaging removing

Be careful not to damage the unit.

Cut-off valves installed at inlet and outlet (both on the water technique circuit as well as that of the hot domestic water) allow maintenance

operations without having to empty the system.

Recycle and dispose of the packaging material in conformity with local regulations.

A Supports for handling: remove after the handling.

WSHN-XEE2 10.2-120.2 9

3 Positioning

During positioning consider these elements:

• Technical spaces requested by the unit

• Electrical connections

• Water connections

• Spaces for air exhaust and intake

3.1 Functional spaces

Functional spaces are designed to:

• guarantee good unit operation

• carry out maintenance operations

• protect authorized operators and exposed people

Respect all functional spaces indicated in the DIMENSIONS section.

Double all functional spaces if two or more unit are aligned.

3.2 Positioning

Units are designed to be installed:

• INTERNAL

• in fi ed positions

Limit vibration transmission:

• use antivibration devices on unit bearing points

• install fl xible joints on the hydraulic connections

Choose the installation place according to the following criteria:

• Customer approval

• safe accessible position

• technical spaces requested by the unit

• max. distance allowed by the electrical connections

• Avoid installations in places subject to floodin

• verify unit weight and bearing point capacity

• verify that all bearing points are aligned and leveled

3.3 Saftey valve gas side

The installer is responsible for evaluating the opportunity of installing drain tubes, in conformity with the local regulations in force (EN 378).

10 WSHN-XEE2 10.2-120.2

4 Water connections

4.1 Water quality

Water features

• confi ming to local regulations

• total hardness < 14°fr

• within the limits indicated by table

The water quality must be checked by qualified personne .

Water with inadequate characteristics can cause:

• pressure drop increase

• reduces energy efficie y

• increased corrosion potential

Acceptable water quality values:

42-

HCO

/SO

42-

Total Hardness

43-

< 100

> 1

4,5 ÷8,5

< 50

< 2,0

NH3< 0,5

PH 7,5 ÷9,0

ppm

Temperature

< 0,5

< 0,05

< 50

< 65

Oxygen content < 0,1

Free Chlorine < 0,5

ppm

ppb

°C

ppm

Provide a water treatment system if values fall outside the limits.

The warranty does not cover damages caused by limestone formations, deposits and impurities from the water supply and / or failure from

failed system clearing to clean system.

4.2 Risk of freezing

If the unit or the relative water connections are subject to temperatures close to 0°C:

• mix water with glycol, or

• safeguard the pipes with heating cables placed under the insulation, or

• empty the system in cases of long non-use

4.3 Anti-freeze solution

The use of an anti-freeze solution results in an increase in pressure drop.

Make sure that the glycol type utilized is inhibited (not corrosive) and compatible with the water circuit components.

Do not use dierent glicol mixture (i.e. ethylene with propylene).

4.4 Water fl w-rate

The project water-fl w must be:

• inside the exchanger operating limits (see the TECHNICAL INFORMATION section)

• guarantee, also with variable system conditions (for example in systems where some circuits are bypassed in particular situations).

4.5 Hydraulic connections

• take away the supplied connection union by acting on the connection joint

• weld the union to the installation pipe

• perform the connection between the installation pipe and the evaporator, using the joint

Do not weld the system pipe with the Victaulic connection joint attached.

The rubber gasket might be irreparably damaged.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CLIVET Pompa di calore

CLIVET

CLIVET CKN-XHE2i 10.1 Manuale utente

CLIVET

CLIVET WSAR-MT-E Manuale utente

CLIVET

CLIVET WiSAN-YEE1 45.4 Manuale utente

CLIVET

CLIVET WSN-XIN Series Manuale utente

CLIVET

CLIVET WSAT-YSI Manuale utente

CLIVET

CLIVET MSAN-XMi 140M Istruzioni per l'installazione

CLIVET

CLIVET CRH-XHE2 49.4 Manuale utente

CLIVET

CLIVET WSAN-XEM 50.4 Manuale utente

CLIVET

CLIVET WSAR-MT Series Guida

CLIVET

CLIVET CSRN-XHE2 Series Manuale utente

CLIVET

CLIVET MSRN-XSC3 + CEV-XN Manuale utente

CLIVET

CLIVET WiSAN-YSE1 10.1 Manuale utente

CLIVET

CLIVET EVH Space 21 Manuale

CLIVET

CLIVET WSAN-XES 18.2 Manuale di servizio

CLIVET

CLIVET MV6R-XMi Manuale di riferimento

CLIVET

CLIVET MSAN 81 Manuale

CLIVET

CLIVET WSAN-XSC3 MF Series Manuale utente

CLIVET

CLIVET WSAN-XIN 21 Manuale utente

CLIVET

CLIVET WSAN-EE 17 Guida

CLIVET

CLIVET CSNX-XHE2 12.2-44.4 Manuale utente

CLIVET

CLIVET WSAN-XIN 21-141 Manuale utente

CLIVET

CLIVET WBAN 41 Guida

CLIVET

CLIVET WSAN-XIN MF 18.2 Manuale utente

CLIVET

CLIVET WSAN-XEE Series Guida

Manuali Pompa di calore popolari di altre marche

MICROWELL

MICROWELL HP 1000 GREEN Manuale utente

Sanyo

Sanyo SAP120FCH Manuale utente

Daikin

Daikin EHYHBH05AA Manuale utente

Panasonic

Panasonic WH-SDF03E3E5 Guida

Bryant

Bryant 544B Manuale utente

Airxcel

Airxcel 45000 Series Manuale

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuale utente

Dimplex

Dimplex LI 16I-TUR Guida utente

Carrier

Carrier WSHP Open v3 Guida rapida alla configurazione

TGM

TGM CTV14CN018A Manuale utente

Carrier

Carrier 38MGQ Series Manuale utente

Kokido

Kokido K2O K880BX/EU Guida alla risoluzione dei problemi

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guida rapida

Carrier

Carrier 48EZN Manuale utente

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Istruzioni operative

Ariston

Ariston NIMBUS Manuale utente

Weishaupt

Weishaupt WWP L 7 Guida utente

GE Zoneline AZ85H09EAC Manuale utente