Clockaudio CDT100 MK3 Manuale utente
1
Clockaudio Ltd.
Unit C, Wellington Gate, Silverthorne Way,
Waterlooville, Hampshire PO7 7XY, UK
Tel: +44(0)23 9225-1193
Fax: +44(0)23 9225-1201
Email: info@clockaudio.co.uk
Clockaudio North America Inc.
2891 Rue du Meunier, Unit 103, Vaudreuil-Dorion,
QC, Canada J7V 8P2
Toll Free: 1-888-424-9797
Tel: 450-424-9797
Fax: 450-424-3660
Email: info@clockaudio.com
Clockaudio PTE Ltd.
BizTech Centre, Unit # 01-02, 627A Aljunied Road,
Singapore, 389842
Tel: +65 67484738
Fax: +65 67484428
Email: info@clockaudio.com.sg
CLOCKAUDIO CDT100 MK3
Dante Transporter
2
IMPORTANT SAFETY INSTRUCTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPARATUS TO RAIN OR MOISTURE.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and third grounding prong. The wider blade or the
third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories as specified by Clockaudio.
• Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, if the apparatus has been exposed to rain or moisture, does not
operate normally or has been dropped.
• This apparatus shall be connected to a mains socket outlet with a protective
earthing connection.
• If rack mounting, provide adequate ventilation. Equipment may be located
above or below this apparatus but some equipment (like large power
amplifiers) may cause an unacceptable amount of hum or may generate too
much heat and degrade the performance of this apparatus.
THIS APPARATUS TO RAIN OR MOISTURE.
3
At the end of the life of this equipment, dispose
of equipment according to local regulations.
LIMITED ONE YEAR WARRANTY
The equipment is warranted for one year from date of purchase from Clockaudio
against defects in materials or workmanship.
This warranty does not cover equipment which has been abused or damaged by
careless handling or shipping.
This warranty does not apply to used or demonstrator equipment.
Should any defect develop, Clockaudio will, at our option, repair or replace any
defective parts without charge for either parts or labor. If Clockaudio cannot correct
the defect in the equipment, it will be replaced at no charge with a new item.
Clockaudio will pay for the cost of returning the replacement equipment to you.
This warranty applies only to items returned to Clockaudio, shipping costs prepaid,
within one year from the date of purchase.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules and EN55032, EN55035.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at their own expense.
4
CONTENTS
GETTING STARTED 5
FEATURE OVERVIEW 6
IN THE BOX 6
DIAGRAM OF FUNCTIONS 7
CONNECTING AUDIO SOURCES 11
CONNECT TOUCH SWITCHES 13
CONNECT TO A DANTE NETWORK 13
CONNECT POWER 14
TOUCH SWITCH PORT SETUP 18
FRONT PANEL SWITCHES &
DEMO/DIAGNOSTIC MODES 18
FRONT PANEL LED INDICATOR 19
CLOCKAUDIO CONTROL PANEL 20
DIAGNOSTIC MODES 22
MICROPHONE PLACEMENT 23
MOUNTING 25
API SPECIFICATION 28
5
GETTING STARTED
The CDT100 MK3 four input Dante interface is the ideal interface for adding
microphone inputs to a Dante system.
Adding touch switches, motorized microphone controls, and LED indication
to your system is simplified with Touch Switch and ARM-C ports. The small
form factor allows the CDT-100 MK3 to be installed in close proximity to the
microphones, minimizing interference-prone analog wiring.
Up to 6 CDT100 MK3 units can be installed in a daisy chain configuration,
further reducing the amount of cabling needed.
6
FEATURE OVERVIEW
• RGB LED control for all Clockaudio RGB LED touch switches.
• 3 logic input pins on each TS port (pins 1, 5 and 8).
• Easy to install with under table mounting flanges.
• Audio and control signals transported over a single network cable.
• 4 balanced mic inputs using 3-pin terminal block connectors.
• Available +48V phantom power to each mic input.
• Powered by an external regulated +12VDC power supply (sold
separately).
• The 4 TS (Touch Switch) connections are fully backward compatible
to all previous Clockaudio bicolor touch switches. The ARM-C port
provides direct connection to the ARM motorized microphone controller
or CCRM4000.
• The CDT100 MK3 features two network connections for Dante Daisy
Chaining. This simplifies system infrastructure wiring, allowing a single
network cable home run for multiple CDT100 MK3 units.
• Power can also be daisy chained, up to 6 units (additional power
considerations are required).
• Compatible with any Dante or AES67 capable audio DSP or other Dante
enabled device.
• The CDT100 MK3 can be controlled and monitored with 3rd party
control modules using direct UDP messages. Parameters that can
controlled include:
• Phantom Power On/Off
• ARM-C Up/Down
• LED Status and Brightness level
• Button Status
IN THE BOX
• CDT100 MK3 Unit
• Quick start card
• 6x 3POS terminal block
• 2x 2POS terminal block
• 2x #6 wood screws
7
MIC 1
MIC 2 MIC 3 MIC 4 OUT 1 OUT 2
PORT 1 PORT 2CDT100 MK3 TS1 TS2 TS3 TS4
22
12 30
40
DEFAULT GAIN
22
12 30
40
22
12 30
40
DEFAULT GAIN
22
12 30
40
DEFAULT GAIN` DEFAULT GAIN
POWER TEST RESET CDT100 MK3
12345678
FEMALE XLR
(front view)
JACK VIEW
1 2
34
DIAGRAM OF FUNCTIONS
1. MIC INPUT TERMINAL BLOCKS
Four channels of microphone preamplification
2. MIC GAIN ADJUSTMENT
Default gain detent (32dB) or 7 - 40dB selectable input gain
3. 12VDC POWER INPUT
External 12VDC power inlet (center positive)
4. POWER INPUT TERMINAL BLOCKS
12VDC power input for external or daisy chained power
5. POWER OUTPUT TERMINAL BLOCKS
12VDC power output for daisy chaining multiple devices
6. OUTPUT TERMINAL BLOCKS
Dante network audio outputs, assignable with Dante Controller
7. TOUCH SWITCH PORT
RJ45 port for connection to Clockaudio Touch Switch controls
8. ARM-C PORT
ARM-C port for connection to Clockaudio motorized microphone control
9. DANTE NETWORK PORTS
Dante network ports for connecting to Dante network and daisy
chaining multiple devices
5
6
789
8
10. POWER ON
Power and CDT100 MK3 Status Indicator
11. TEST
Activates diagnostic and demo modes
12. RESET
Resets the test mode and restore defaults (see FRONT PANEL
SWITCHES & DEMO/DIAGNOSTIC MODES section for detailed
information)
MIC 1
MIC 2 MIC 3 MIC 4 OUT 1 OUT 2
PORT 1 PORT 2CDT100 MK3 TS1 TS2 TS3 TS4
22
12 30
40
DEFAULT GAIN
22
12 30
40
22
12 30
40
DEFAULT GAIN
22
12 30
40
DEFAULT GAIN` DEFAULT GAIN
POWER TEST RESET CDT100 MK3
12345678
FEMALE XLR
(front view)
JACK VIEW
10 1211
9
SETTING UP THE CDT100 MK3
We recommend setting up the CDT100 MK3 in the following order. Consult
this User Guide for detailed information on each step.
1. Mount the CDT100 MK3
2. Connect audio sources
3. Connect Touch Switches and ARM Controller
4. Connect CAT5 cables to a Dante Network
5. Connect power supply
6. Configure the CDT100 MK3 to transmit and receive
on the Dante Network via Dante Controller
7. Adjust preamp gain if necessary
8. Connect the Clockaudio Control Panel application
for deeper configuration of key features
9. Setup TS Port functionality
10. Setup ARM-C functionality
11. Test features with DEMO/DIAGNOSTIC mode
10
CONNECTION DIAGRAMS
CONNECTING MICROPHONES AND TS SWITCH
CONNECTING ARM-C MOTORIZED MICROPHONES AND TS SWITCH
DANTE PORTS
CO12EN-RF BOUNDARY MICROPHONES
TS-C1
UP TO 4 TOUCH SWITCHES
ARM102N-RF MOTORIZED MICROPHONES + ARM-C MOTOR CONTROL
TS-C1
UP TO 4 TOUCH SWITCHES
CONNECT UP TO 6 DEVICES TOTAL IN
DAISY CHAIN CONFIGURATION
TS005
TS003 ARM-C MOTOR CONTROL
RJ45 to ARM-C
DANTE PORTS
CO12EN-RF BOUNDARY MICROPHONES
TS-C1
UP TO 4 TOUCH SWITCHES
ARM102N-RF MOTORIZED MICROPHONES + ARM-C MOTOR CONTROL
TS-C1
UP TO 4 TOUCH SWITCHES
CONNECT UP TO 6 DEVICES TOTAL IN
DAISY CHAIN CONFIGURATION
TS005
TS003 ARM-C MOTOR CONTROL
RJ45 to ARM-C
Indice
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
