CMS Velocity Series Manuale

Removable Backup System

Hardware Installation Guide

Installing the Velocity Series Removable Backup System .......... 2-3

Connecting the Velocity Series Removable Backup System ..... 4-5

Setting Up the Velocity Series Removable Backup System ...........

Changing Your Computer’s Setup Conguration ........................... 7-9

Removing the Velocity Series Removable Drive ..........................

CMS Support .................................................................................11

Your new CMS Velocity Series Removable Backup System comes fully assembled. A 4-pin power connector and

Serial ATA cable are included for the connection of the Removable Serial ATA hard drive into your computer. The

following items are also included:

1 Velocity Series Removable Backup System 1 BounceBack Professional software CD-ROM

1 Getting Started Guide 4 Screws

Installing the Velocity Series Removable Backup System

1 Shut down your computer.

2 Remove/Unplug the computer’s power cable.

3 Carefully open your computer case to gain access to the inside.

Please refer to your computer’s Manual if you are not sure how

to properly open your case.

Note: Installation requires an unused/empty 5.25” drive bay slot (see

Figure 1).

4 Remove the selected 5.25” drive bay face plate.

5 You will need to determine if the selected drive bay will require

screws or guide rails to mount the Removable bay.

Installing the Velocity Series Removable Backup System

Figure 1: Unused/empty drive bay

Installing the Velocity Series Continued...

Mounting the Removable Backup System with screws: If the selected drive bay will require screws to mount

the Removable Backup System, you will nd four screw holes, two on each side of the unused bay.

• Install the Removable Backup system into the unused bay through the front opening of the computer case

(where you removed the face plate).

• Slide the Removable Backup system all the way into the unused bay until the screw holes match up.

• Use the provided screws to secure the Removable bay into place.

Mounting the Removable Backup System with guide rails: If the selected

drive bay will require guide rails to mount the Removable Backup System

into place, you can connect the rails directly onto the sides of the System.

(see your computer’s Manual for the location of your drive bay’s guide rails.)

• Install the guide rails onto the sides of the Removable Backup System

using the four screws provided with this product.

• Slide the Removable Backup system into the unused drive bay through

the back (or front depending on your system) of the bay until the rails

lock into place (see Figure 2).

Note: You may need to temporarily disconnect a few cables to gain access

to the selected drive bay. This will allow you to slide the Removable Backup

System into place through the back of the selected bay as shown in Figure 2.

Remember to reconnect the cables after you have installed the system.

Figure 2: Installing the Removable bay

into the unused bay.

Connecting the Velocity Series Removable Backup System

Follow these steps to connect the Velocity Series Removable Backup

System’s Serial ATA hard drive to your computer:

1 Connect the Removable Backup System’s 4-pin power connector to

an available power connector in your case (see Figure 3).

2 Connect the Removable Backup System’s Serial ATA connector:

• If your mother board has available onboard Serial ATA connectors,

insert the Removable Backup System’s Serial ATA cable into an

available connector (see Figure 4).

• If your mother board does not have an available onboard Serial

ATA connector, you will need to install a Serial ATA PCI Controller

Card rst. Follow the installation instructions of the guide that ships

with the Serial ATA PCI Controller Card. (Serial ATA PCI Controller

Cards can be purchased from CMS at (714) 424-5520 or online at

www.cmsproducts.com, part number: VELOCITY-CONT).

Once the Serial ATA PCI Controller Card is installed, you can

connect the Removable Backup System’s Serial ATA connector to

your Serial ATA PCI Controller Card.

3 Before you close your computer, please make sure you have completed all the necessary steps for

installing the Velocity Series Removable Backup System. Use the provided check list.

Figure 3: Available power connector

Figure 4: Onboard Serial ATA

connectors

Connecting the Velocity Series Continued...

Velocity Series Removable Backup System Installation Check List:

Shut down your computer and remove/unplug the power cable.

Carefully open your computer case.

Locate an unused 5.25” drive bay and remove it’s face plate.

Mount the Velocity Series Removable Backup System into the selected unused drive bay and secure it

into place using either the screws or guide rails as detailed in the instructions.

Connect the Removable Bay’s 4-pin power connector.

Connect the Removable Bay’s Serial ATA connector.

4 Close your computer case.

Setting Up the Velocity Series Removable Backup System

1 Turn your computer back on.

2 Windows should recognize the new Velocity Series Serial ATA hard drive and install the correct driver for

you. To verify that the Velocity Series has been installed properly, follow these steps:

• Click Start and then My Computer. The Velocity Series Serial ATA hard drive should now be listed in

your device list. If so, you can now begin the installation of the BounceBack Professional Software (see

Installing the BounceBack Professional Software). If the Velocity Series Serial ATA hard drive does not

appear in your device list, your computer may not have “automatic conguration” enabled.

Review the information in the next section, “Changing Your Computer’s Setup.”

If the Velocity Series is not recognized by your computer (in the “My Computer” folder) in the device list you will need

to enter your computer’s setup. The following steps will guide you through this process.

1 Restart your computer. Watch carefully for the startup key information. In most cases this will show up in

one of the corners of your screen as the computer restarts. The key information will only be present for a

short amount of time.

2 Quickly press the appropriate key,

Typically the F2 key depending on

your computers manufacturer(refer

to your computer’s Manual if you

need additional help with this step).

This will take you to your computer’s

setup screens.

Changing Your Computer’s Setup

Select

Figure 5

Select Drive Conguration and

press Enter.

The next screen will describe your

drive conguration and how to

proceed. Read the information on

types of possible congurations

which will help you choose your

path.

Check to see what your current conguration is below (A, B or C). In this example our computer is congured like

Conguration A below, where Yes means enabled or in use and No means not in use or unknown device.

Conguration A Conguration B Conguration C

SATA Primary Drive Yes Yes No

SATA Secondary Drive No Yes No

Primary Master Drive Yes No Yes

Primary Slave Drive No No No

SATA PCI Controller Required No Yes Maybe

Depending on your conguration above, select the

appropriate device type and press the Enter key:

Conguration A — Select the Secondary SATA Drive.

Conguration B — You will need to install a SATA PCI

Controller because all your SATA ports are in use.

Conguration C — Select the SATA Primary

Drive. You should then enter the Boot Order

Setup to verify that your Primary Master Drive

is the boot Drive. Note: If you are unable to

change the Boot Order you will need to either

change your internal hard drive to a SATA drive

or install a PCI SATA Controller Card.

Select

Figure 6

Changing Your Computer’s Setup Continued...

Select

Figure 7

1 Select Drive Type and then press the

Enter key .

2 Use the + or – key to scroll through the

options. Make sure the Drive Type is set

to AUTO as in the example.

3 Use the Esc key to exit and save your

new settings.

Changing Your Computer’s Setup Continued...

Removing the Velocity Series Removable Drive

The Velocity Series Removable hard drive can be ejected from

the front of the computer.

1 Always turn off your computer before ejecting the drive.

2 Pull the handle on the Velocity Series outward and

carefully remove the drive (see gure 8).

Figure 8: Ejected Velocity Removable

Hard Drive

Indice

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente