CNC4PC C34HS2 Manuale utente

USER’S

MANUAL

VER. 1

C34HS2 BOARD

Rev. 1

OCTOBER, 2020

User’s Manual Page i

USER'S MANUAL

TABLE OF CONTENTS

Contents Page #

1.0 OVERVIEW.....................................................................................................................1

2.0 FEATURES.....................................................................................................................1

3.0 BOARD DESCRIPTION..................................................................................................1

4.0 JUMPER TO SELECT THE ENABLE.............................................................................2

5.0 ALARM TERMINAL........................................................................................................4

6.0 WIRING SAMPLE...........................................................................................................4

7.0 PINOUT...........................................................................................................................5

8.0 DIMENSIONS..................................................................................................................6

User’s Manual Page 1

1.0 OVERVIEW

This board interface is used for the connection between C82, C76, M16D and Closed

Loop Steppers DRIVE.

2.0 FEATURES

•RJ45 Driver Input Connector

•Select Jumper for Hard Enable or Soft Enable.

•Alarm terminal

•Select jumper for signal differentials.

•Select Jumper active Low and active High

•Adjustable resistor to allow adjusting the fault sensibility

3.0 BOARD DESCRIPTION

User’s Manual Page 2

4.0 JUMPER TO SELECT THE ENABLE

Use Software Enable to keep the driver active only while the system is active.

Set of jumpers as shown in the image.

SOFT ENABLE

Use Hardware Enable to keep the driver enabled all the time.

Set of jumpers as shown in the image.

HARD ENABLE

JUMPER TO SELECT THE DIFFERENTIAL

If working the inputs of STEP and DIR as differentials signals, you have to use the board, set

jumper as shown in the image.

DIFERENTIAL

User’s Manual Page 3

If not use the differential signal for STEP & DIR, set jumper as show in the image.

STEP & DIR

JUMPER TO SELECT ACTIVE LOW AND ACTIVE HIGH

1-2: ACTIVE LOW

2-3: ACTIVE HIGH

User’s Manual Page 4

5.0 ALARM TERMINAL

6.0 WIRING SAMPLE

User’s Manual Page 5

7.0 PINOUT

C34HS CONNECTOR RJ45

RJ45 Pins

Function

NOT USED

PUL+

NOT USED

GND

ERR

DIR+

NOT USED

8 (5V)

EN+

User’s Manual Page 6

8.0 DIMENSIONS

All dimensions are in Millimeters.

DISCLAIMER

Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC

nor Arturo Duncan are liable for any accidents resulting from the improper use of these

devices. This product is not a fail-safe device and it should not be used in life support

systems or in other devices where its failure or possible erratic operation could cause

property damage, bodily injury or loss of life.

Indice

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente