Coastal BLU-e Istruzioni per il montaggio
BLU-e FITTING GUIDE
AND INSTRUCTION MANUAL
FITTING GUIDE
2BLU-e Fitting Guide
FITTING GUIDE
BLU-E FITTING GUIDE AND INSTRUCTION MANUAL
LIT-FG-BLU-e
Fitting Guide – Hardware component list
– Wiring diagram
– Mounting plate & control unit relay
– Connecting components & wiring
User Instructions – First steps
– System Back up – very important!
– How to clean the scanner unit
Information – What do the LED colour signals mean?
– QR Codes for Ekey website for further information
LIST OF CONTENT
1.
2.
3.
3-4
5-6
7-8
9-12
13
14
15
16-19
20
3
www.coastal-group.com
FITTING GUIDE
BLU-E BIOMETRIC PULL HANDLE
LIT-FG-BLU-e
The primary purpose of the product is to open doors. This can be carried out using the Fingerprint Scanner, Bionyx
App or Alexa. These instructions are a brief overview of the system and how to complete the basic tasks upon
installation, for more detailed information and troubleshooting please refer to the manufacturer’s website via the
links below.
We advise you get a qualied electrician to wire up the system, wiring diagrams are shown within the ‘wiring
diagram’ section on page 5 and 6 of this document.
QR CODES
RISK OF ELECTRIC SHOCK / DAMAGE TO THE SYSTEM IF
INSTALLED INCORRECTLY!
Wiring
diagrams
Customer
training
Mounting
instructions
dLine FAQs Data sheets Instructions for
tters
NOTE: Coastal highly recommends tting a Euro cylinder as an override, in case of power failure.
4BLU-e Fitting Guide
FITTING GUIDE
HARDWARE COMPONENTS LIST
LIT-FG-BLU-e
ML-E-CBLW
Cable W - joining Electric Motor to
Control Unit 6m
CX-BLU-E-CU
Control Unit
CX-BLU-E-CU-MP
Control Unit Mounting Plate
CX-BLU-E-SCU-HC3
Cable joining BLU-e Handle to
Control Unit 3m
ML-E-PSU
Power Supply Unit 240v to 12v
CX-BLU-E-CT2
Cable Transfer Unit
ML-E-EMTR
Electric Motor Unit (ts to locks
ML120, ML3120 and ML480)
Below is a list of components you will receive with your Blu-e Biometric Pull Handle Kit. These components will
include all the entry system and electrical components you need to work with your door lock.
PLEASE NOTE: This kit does not include the lock or keeps, these are purchased separately.
BLU-E-HAB15-900-UF-SSS
or BLU-E-HAB15-900-UF-PBK
Pre-wired pull handle and ngerprint
scanner unit
1
3
67
2
4
3
5
5
www.coastal-group.com
FITTING GUIDE
WIRING DIAGRAM
LIT-FG-BLU-e
Risk of electrocution: All ekey devices are
to be operated with Safety Extra Low
Voltage (SELV). Only use power supplies
rated protection class 2 with safety
approval according to EN 62368-1.
Failure to do so will create a risk of fatal
electrocution.
Only certied electricians are authorised
to carry out electrical installation work on
mains systems.
Property damage in the event of
incorrect mounting and wiring: The
system devices are operated using
electricity.
They could be destroyed if they are
mounted and wired incorrectly.
Mount and wire the system devices
correctly before connecting the power.
This wiring diagram is not subject to
updating. We reserve the right to make
technical modications and change the
product's appearance; any liability for
errors and misprints is excluded.
DANGER
ATTENTION
NOTICE
2
3
4
5
6
7 1
COLOUR DESCRIPTION
White VDC (+) (12-24)
Brown GND (-)
Green ekey bus
Yellow ekey bus
Blue Input
Grey Input
Pink For testing purposes
Red For testing purposes
FITTING GUIDE
WIRING DIAGRAM
LIT-FG-BLU-e
CONNECTION TO THE MOTORISED LOCK
CONNECTION TO THE CONTROL UNIT
CONNECTION TO THE ELECTRICAL INSTALLATION
PIN COLOR DESCRIPTION
- Green Switching impulse (+)
- Brown GND (-)
- White VDC (+)
PIN COLOR DESCRIPTION
4 - -
3 Green Switching impulse (+)
2 Brown GND (-)
1 White VDC (+)
See connection conguration
of the motorised lock
manufacturer
Potential-free request-
to-exit button for manual
door opening
Each unused core must be insulated separately!
4321
6BLU-e Fitting Guide
11
20 24
>4 0
>2 5
2831
480
15110
49
25
20
478 0.50
+
-
498 0.50
+
-
511 0.50
+
-
11
1.5
24
1.5
17.5 31.53
+
-
7
www.coastal-group.com
Technical data:
Electrical parameters: 2.5 A; 48 VDC
Cable: Li9Y11Y, 8 x 0.34 mm², RoHS compliant
IP rating: IP40/connector IP67
Temperature: from -20 °C to +75 °C
These Mounting instructions are not subject
to updating. We reserve the right to make
technical modications and change the
product‘s appearance; any liability for errors
and misprints is excluded
NOTICE
MOUNTING INSTRUCTIONS EKEY DLINE CABLE TRANSFER
LIT-FG-BLU-e
Dimension
Milling dimensions for mounting into solid / hollow proles
17
Y
130
X
A
A
Section A-A
160
X
Y
X
130
45
2.7
X
17
130
Y
DIMENSION
X Y
dLine controller mounting plate e/r16
182 mm
17 mm
dLine controller mounting plate e/r20 21 mm
dLine controller mounting plate e/r24 25 mm
The milling prole varies depending on the mounting plate which is used.
For mounting plate dimensions see:
8BLU-e Fitting Guide
MOUNTING INSTRUCTIONS EKEY DLINE CABLE TRANSFER
CX-BLU-E-CU & CX-BLU-E-CU-MP
LIT-FG-BLU-e
9
www.coastal-group.com
FITTING GUIDE
CONNECTING COMPONENTS AND WIRING
LIT-FG-BLU-e
1. CONNECTING THE TRANSFER UNIT TO THE FRAME CABLE
Connect transfer cable to power supply cable and tighten small screw to keep the two halves together.
Place small cover cap onto transfer cable to cover xing screw.
The transfer unit connects to the power supply unit by the means of the frame cable, this is the white cable that
is provided in the transfer unit bag, this cable locates on the frame as shown below and the cable runs back to the
power supply unit. (See page 7 for transfer unit’s milling details).
Pass white cable through pre-drilled holes in frame as per drawings on Page 7.
Fix transfer unit to frame with backplate and screws provided.
10 BLU-e Fitting Guide
FITTING GUIDE
CONNECTING COMPONENTS AND WIRING
LIT-FG-BLU-e
2. MOTOR CONNECTION
Connect the motor to the back of the lock in the appropriate location for lock provided this can be identied by the
cut-outs provided in the bar behind the faceplate. Secure the motor to the faceplate by means of the three screws
supplied, (these are reverse thread).
Push the blue connector on the cable into the blue receptor on the motor in the correct orientation.
3. CONNECTION OF SEPARABLE CABLE FROM BAR HANDLE TO CABLE FOR
CONTROL RELAY UNIT
The separable cables have a tear drop alignment mark on both parts, align these marks and push the two cables
together and then screw the knurled sleeves together to ensure a tight t of the cables.
Take the other end of separable cable with the four-pin plug and plug into corresponding four-pin socket on the
control relay unit.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Coastal Serratura della porta
