Cocraft HS400-D Manuale utente

ENGLISHSVENSKANORSKSUOMIDEUTSCH

Important!

Read the entire instruction manual

carefully and make sure that you fully

understand it before you use the

equipment. Keep the manual for future

reference.

Viktig information:

Läs hela bruksanvisningen noggrant och

försäkra dig om att du har förstått den

innan du använder utrustningen. Spara

bruksanvisningen för framtida bruk.

Viktig informasjon:

Les disse anvisningene nøye og forsikre

deg om at du forstår dem, før du tar

produktet i bruk. Ta vare på anvisningene

for seinere bruk.

Tärkeää tietoa:

Lue nämä ohjeet huolellisesti ja varmista

että olet ymmärtänyt ne, ennen kuin

alat käyttää laitetta. Säilytä ohjeet

myöhempää tarvetta varten.

Wichtiger Hinweis:

Vor Inbetriebnahme die komplette

Bedienungsanleitung sorgfältig

durchlesen und aufbewahren.

HS400-D

FLOAT SWITCH,AUTOMATIC OPERATION

18-3567 • 40-9032 • 18-3568 • 40-9033

SUBMERSIBLE PUMP

DRÄNKBAR PUMP SENKEPUMPE

UPPOPUMPPU TAUCHPUMPE

Ver. 20160524

Original instructions

Bruksanvisning i original

Originalbruksanvisning

Alkuperäinen käyttöohje

Original Bedienungsanleitung

Art.no Model

18-3567 LKS-400P

40-9032 LKS-400P

18-3568 LKS-750PW

40-9033 LKS-750PW

ENGLISH

150/233l/min Submersible Pump

Art.no 18-3567 Model LKS-400P

40-9032 LKS-400P

18-3568 LKS-750PW

40-9033 LKS-750PW

Please read theentire instruction manual before using theproduct and save it for future

reference. We reserve theright for any errors in text or images and any necessary

changes made to technical data. If you have any questions concerning technical

problems please contact our Customer Services.

Safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of theappliance in asafe way and understand

thehazards involved.

• Children shall not play with theappliance.

• Cleaning and user maintenance shall not be made by children

without supervision.

• Always use aresidual current device (RCD or RCCB) which

trips at < 30 mA between thepump and thepower supply.

• Always inspect thepump before using it, especially thepower

lead and plug. Never use thepump if it is damaged.

• If thesupply cord is damaged, it must be replaced by

themanufacturer, its service agent or similarly qualiﬁed

persons in order to avoid ahazard.

• Make sure that any electrical connections (extension lead,

RCD, etc.) are placed in adry place and protected from

overﬂowing water and ﬂoods.

• Keep themains lead away from extreme heat, oil and sharp edges.

• Thepump is not designed for continuous use.

• Protect thepump from frost.

ENGLISH

• Thepump is suitable for pumping clean water or dirty water

with amaximum particle size of 5 mm for 40-9032 and 25 mm

for 40-9033, swimming pools and ornamental ponds. Bear

in mind that sand and other abrasive substances in theliquid

that is pumped will increase thewear and tear and reduce

thecapacity of thepump.

• Thepump must never be used in aswimming pool or pond if

people or animals are still in thewater.

• Thepump is waterproof and submersible to adepth of max 7/7 m.

• Make sure that thepressure head does not exceed 7/8 m.

• Thepump must not be used for corrosive, combustible

or explosive liquids such as petrol, kerosene or thinners.

Neithermust thepump be used for grease, oil, brackish

water, seawater, urine or toilet sewage water.

• Thetemperature of thepumped liquid must not be greater

than 35 ºC.

• Dry-running should be avoided, as this soon wears thepump

out. Turn off thepump as soon as water has stopped coming

out of thehose.

• Avoid running thepump with thedischarge outlet closed for

more than ten minutes.

• Thepump has abuilt-in thermal overload motor protection and

automatically shuts off when it gets overheated. Themotor

starts again automatically when themotor has cooled.

• If chlorinated water, such as swimming pool water, has been

pumped, clean water should be pumped afterwards to rinse

out thepump.

ENGLISH

Product description

Thepump is intended for domestic use in homes and gardens. Suitable uses:

• Drainage of containers

• Thetransfer of liquids

• Pumping water from springs, wells and barrels

• Bilge pumping boats

• Circulating water for limit periods

1. Upper outlet (1¼″female thread)

2. Float switch cable clip

3. Carrying handle

4. Power lead with plug

5. Float switch

6. Lower outlet (1¼″female thread)

7. Plug for theoutlet which is not used

8. Base with inlet

9. Connections:

- Universal hose union 38 mm

and 25 mm + 1″and 1¼″

male thread

- 90° elbow, 1¼″male thread

- Straight hose connector,

1¼″male thread

678

ENGLISH

Before use

Hose Connection*

Fit theincluded universal hose union onto

one of theoutlets (1 or 6)*.

Note: Theplastic plug (7) should be inserted

into theoutlet which is not being used.

Theuniversal hose union is ﬁtted with

a38mm (1½″) and 25mm (1″) diameter

barbed hose connectors and a1″male

threaded hose connector. 38mm hoses

provide thebest capacity.

If the38mm barbed hose connector or

the1″threaded connector are to be used,

theend of thenipple should be cut off as

shown in theﬁgure.

Cut off thepart (B) of theuniversal hose union

that is not needed (if using large diameter hose).

* Thepump has two alternative outlets, upper

and lower. Depending on theconstruction of

thepump theupper outlet (1) provides about

10% less water ﬂow than thelower outlet (6).

Note: Theplastic plug (7) must be inserted

into theoutlet which is not used.

Adjusting the Float Switch

Thelevel of water at which thepump starts

and stops can be adjusted by lengthening

or shortening theﬂoat switch cable held by

theclip (2).

• Shortening thelength of thecable between

theswitch (5) and theclip (2) will enable

thepump to start at alower water level.

• Lengthening thelength of thecable

between theswitch (5) and theclip (2)

will enable thepump to start at ahigher

water level.

ENGLISH

Positioning and transportation

• Thepump should be placed in astable position (especially if set to automatic operation).

• Theﬂoat switch (5) must be able to move unhindered.

• Theinlet must not be blocked in any way, make sure that there are no loose

particles such as sand or stones near theinlet as this increases wear on thepump

and could even cause astoppage.

• Do not use themains lead or ﬂoat switch to lift or carry thepump. Always use

arope tied to thehandle when lowering or raising thepump.

Operating instructions

Manual operation

Fasten theﬂoat switch so it is not hanging

down. Switch thepump on/off by either using

theswitch on thewall socket if it has one or by

pulling theplug out of thewall socket. Do not let

thepump run dry.

Automatic operation

When themains lead is connected to alive wall socket thesubmersible pump will

be switched on and off by theﬂoat switch. When theﬂoat switch is raised by water,

thepump starts. When thewater level falls, theﬂoat switch hangs down and

thepump stops.

ENGLISH

Care and maintenance

If necessary, unplug themains lead from thewall

socket, remove the3 screws holding thecover plate

onto thebase of thepump, then remove the4 screws

holding theimpeller housing and clean theinlet (8) of

any debris.

Screw theparts back on in reverse order, making sure

that theoutlet on theimpeller housing is on thesame

side of thepump as theupper outlet.

Troubleshooting guide

Problem Possible cause Possible solution

Thepump runs

but doesn’t

pump.

1. Air in pump, outlet

is blocked.

2. Air trapped in suction pipe.

3. Impeller is blocked.

4. When thepump starts

thewater level falls to

below theminimum level.

1. Clean thehose, straighten any

kinks, etc.

2. Wait 60 seconds until thepump

is purged of air, switch it off

and then start it again.

3. Unplug thepump from

thepower supply and remove

any debris from thewater inlet.

4. Place thepump lower in

thewater.

Thepump won’t

start or stops

under load.

1. Thethermal protection

device has tripped.

2. Wall socket is not live.

3. Dirt lodged in

theimpeller housing.

1. Unplug pump and clean

thebase and impeller housing.

Remember that themax liquid

temperature is 35°C.

2. Check fuses and RCD, etc.

3. Unplug thepump from

thepower supply and remove

any debris from thewater inlet.

Thepump runs

but theﬂow rate

falls suddenly.

Impeller is blocked. Unplug thepump from thepower

supply and remove any debris

from thewater inlet.

Pump doesn’t

stop when water

level has fallen.

Theﬂoat switch is prevented

from sinking.

Place thepump so that theﬂoat

switch can move freely.

ENGLISH

Disposal

Dispose of your waste responsibly, sort and recycle where possible. All machines, hoses and

packing material should be sorted and handled according to local environmental regulations.

Specifications

Model LKS-400P LKS-750PW

Wattage 400W 750W

Rated voltage 220–240V AC,

50Hz

220–240V AC, 50Hz

Pump Capacity 150l/min 233l/min

Pressure head 7m 8m

Max submersible depth 7m 7m

Max particle size 5mm 25mm

Max water temperature 35°C 35°C

Hose connection 25mm and 38mm 25mm and 38mm

Union thread 1¼″(female) × 2 1¼″(female) × 2

Length of mains lead 10m (H05RN-F) 10m (H05RN-F)

Ingress protection IPX8 IPX8

Weight 3.6kg 4.9kg

SVENSKA

Dränkbar pump 150/233 l/min

Art.nr 18-3567 Modell LKS-400P

40-9032 LKS-400P

18-3568 LKS-750PW

40-9033 LKS-750PW

Läs igenom hela bruksanvisningen före användning och spara den sedan för framtida

bruk. Vi reserverar oss för ev. text- och bildfel samt ändringar av tekniska data.

Vid tekniska problem eller andra frågor, kontakta vår kundtjänst.

Säkerhet

• Apparaten får användas av barn från 8 år och av personer

med någon form av funktionsnedsättning, brist på erfarenhet

eller kunskap som skulle kunna äventyra säkerheten, om de

har fått instruktioner om hur produkten på ett säkert sätt ska

användas och förstår faror och risker som kan uppkomma.

• Låt aldrig barn leka med produkten.

• Rengöring och skötsel får inte utföras av barn utan vuxens närvaro.

• Anslut alltid pumpen via en jordfelsbrytare som löser ut vid

< 30 mA felström.

• Kontrollera alltid pumpen före användning, särskilt nätsladden

och stickproppen. Använd aldrig pumpen om den är skadad.

• Om nätsladden skadats får den, för att risk för elektrisk stöt

eller brand ska undvikas, endast bytas av tillverkaren, dess

serviceställe eller av en kvaliﬁcerad yrkesman.

• Se till att elanslutningar (skarvuttag, jordfelsbrytare etc.) är

placerade på torr plats, skyddade vid ev. översvämning.

• Utsätt inte nätsladden för stark värme, olja eller vassa kanter.

• Pumpen är inte konstruerad för att användas kontinuerligt.

• Skydda pumpen mot frost.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Cocraft Pompa dell'acqua

Cocraft

Cocraft LKJ-1300SA Series Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente