Code Alarm CATX130 Istruzioni operative

Model CATX130

Programming Guide

The keychain transmitters included with the system have been pre-programmed at the factory,

with each button pre-assigned to control a specific function of the system.

The system will store codes from up to 8 different transmitters. If a 9th transmitter is

programmed to the system, then the first transmitter programmed to the system will be

erased from the system’s memory.

To program new or additional transmitters, the alarm must be disarmed and out of valet mode:

1. Open the drivers door (verify that the vehicle’s interior light turns on.

2. Turn the ignition key to the ON or RUN position.

3. Press and hold the emergency override button

3a. After 10 seconds the horn will honk three (3) times. This indicates

that the system has entered transmitter programming mode.

4. Release the emergency override button.

5. Press the LOCK icon button on the remote transmitter to be programmed.

5a. The horn/siren will sound 1 time, indicating that the system has

“learned” that remote transmitter.

6. Repeat step 5 for any additional remote transmitters.

Deleting Lost or Stolen Remote Controls from Your System

If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to

remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls

to Your System.

3a. If you have only one remaining remote control, press the

LOCK button on that remote control eight (8) times, pausing

at least 1 second in between each press. The horn must

“honk” each time you press the LOCK button.

3b. If you have two remaining remote controls, press the LOCK

button on each remote control four (4) times, pausing at least

1 second in between each press. The horn must “honk” each

time you press the LOCK button.

3c. If you have three remaining remote controls, press the

LOCK button on two of the remote controls three (3) times, then press the

LOCK button on the remaining remote control twice. Pause at

least 1 second in between each press. The horn must “honk”

each time you press the LOCK button.

4. Turn the vehicle ignition off to exit the programming mode. When you are finished, the lost

or stolen remote control will no longer operate your system.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one.

Be sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX130

Programming Guide

Indice

Altri manuali Code Alarm Allarme auto

Code Alarm

Code Alarm CA 310 Manuale utente

Code Alarm

Code Alarm CA 420 Manuale utente

Code Alarm

Code Alarm CA 1150 Manuale utente

Code Alarm

Code Alarm F10 Manuale utente

Code Alarm

Code Alarm 2000 Manuale utente

Code Alarm

Code Alarm CATX630 Istruzioni operative

Code Alarm

Code Alarm CA 6551 SST Manuale utente

Code Alarm

Code Alarm CA-500 Manuale utente

Code Alarm

Code Alarm CA 680 Manuale utente

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuale utente

Code Alarm

Code Alarm CA-230 Manuale utente

Code Alarm

Code Alarm F20 Manuale utente

Code Alarm

Code Alarm 2000 Manuale utente

Code Alarm

Code Alarm CATX120 Istruzioni operative

Code Alarm

Code Alarm PRO 3500 Specifiche

Code Alarm

Code Alarm Professional 1000 Manuale utente

Code Alarm

Code Alarm CA-140 Manuale utente

Code Alarm

Code Alarm ca6355E Manuale utente

Code Alarm

Code Alarm CA 610 Manuale utente

Code Alarm

Code Alarm ca 1151 Manuale utente

Code Alarm

Code Alarm PowerCode PC 7300 Manuale utente

Code Alarm

Code Alarm CA 170 Manuale utente

Code Alarm

Code Alarm CA-670 Manuale utente

Code Alarm

Code Alarm CA 421 Manuale utente

Manuali Allarme auto popolari di altre marche

Clifford

Clifford 3606X Manuale utente

Ultra Start

Ultra Start 2500M SERIES Manuale utente

Ultra Start

Ultra Start 650 Series Manuale utente

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuale utente

Sparkrite

Sparkrite SRA8 Manuale utente

Viper

Viper 4708V Manuale utente

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuale

Falcon

Falcon Predator XL3 Guida utente

Audiovox

Audiovox Auto Security XR91 Istruzioni operative

Clifford

Clifford Sabre II Manuale utente

CrimeStopper

CrimeStopper CS-8717 Guida rapida

Ultra Start

Ultra Start 450 SERIES Manuale utente

Scytek electronic

Scytek electronic Vectra X3 Manuale utente

Excalibur

Excalibur AL-1860-EDPB Manuale utente

Clifford

Clifford CYBER 2 Manuale utente

Gemini

Gemini 7057 Manuale utente

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuale utente

Magicar

Magicar FAI-440 Manuale utente