Cognex VisionView Manuale utente
VisionView®VGA
Manual
1
Declaration of Conformity
Manufacturer Cognex Corporation
One Vision Drive
Natick, MA 01760 USA
Declares this -marked Machine Vision System Product
Product Type: Type 821-0031-1R
Complies With: 2004/108/EC Electromagnetic Compatibility Directive
Compliance
Standards:
EN55022:2006 +A1:2007 (Class A)
EN55024:1998 +A1:2001 +A2:2003
EN61000-3-3:1995 +A1:2001 +A2:2005
EN61000-3-2:2006
European
Representative:
COGNEX INTERNATIONAL
Immeuble “Le Patio”
104 Avenue Albert 1er
92563 Rueil Malmaison Cedex - France
Safety and Regulatory
FCC FCC Part 15, Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at their own expense.
KCC CGX-VVVGA
NRTL TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 60950-1
CB TÜV SÜD AM, IEC/EN 60950-1. CB report available upon request.
RoHS RoHS 6 Compliant
Note: For the most up-to-date regulations and conformity information, refer to the Cognex online support site:
www.cognex.com/Support/VisionView.
2
Precautions
Observe these precautions when installing the VisionView VGA to reduce the risk of
injury or equipment damage:
VisionView VGA is intended to be supplied by a NRTL listed power supply with its•
output rated 24VDC, at 1A minimum with a maximum short circuit current rating
of less than 8A and a maximum power rating of less than 100VA and marked
Class 2 or Limited Power Source (LPS). Any other voltage creates a risk of fire
or shock and can damage VisionView VGA components. Applicable national and
local wiring standards and rules must be followed.
To reduce the risk of damage or malfunction due to over-voltage, line noise,•
electrostatic discharge (ESD), power surges, or other irregularities in the power
supply, route all cables and wires away from high-voltage power sources.
Do not install VisionView VGA in areas directly exposed to environmental•
hazards such as excessive heat, dust, moisture, humidity, impact, vibration,
corrosive substances, flammable substances, or static electricity.
VisionView VGA should be mounted with sufficient clearance to allow air•
circulation through the vents.
VisionView VGA does not contain user-serviceable parts. Do not make any•
electrical or mechanical modifications. Unauthorized modifications may void your
warranty.
Changes or modifications not expressly approved by the party responsible for•
regulatory compliance could void the user’s authority to operate the equipment.
VisionView VGA is intended for indoor use only.•
Cable shielding can be degraded or cables can be damaged or wear out more•
quickly if a bend radius or service loop is tighter than 10X the cable diameter.
Service loops should be included with all cable connections.•
3
1
3
5
2
4
6
Legend*
1 = VGA Cable
2 = RJ-45 LAN Cable
3 = Touch Screen
Cable
4 = USB Cable
5 = Power Connector
6 = Ethernet Cables
*The legend numbers also
correspond with the numbered
Installation steps.
4
1Connect the VGA Cable
Connect a VGA cable to VisionView VGA’s VGA port, and connect the other
end of the cable to a monitor or a touch screen’s VGA port.
VisionView VGA Support
VisionView software instructions are presented in detail in the VisionView®Software
Manual, which is included on the VisionView CD and available for download from the
VisionView support site: www.cognex.com/Support/VisionView.
Installation
Note: Cables are sold separately. If any of the contents appear to be missing or
damaged, immediately contact your Cognex Authorized Service Provider (ASP) or
Cognex Technical Support.
2Connect the Network Cable
Connect an RJ-45 cable to VisionView VGA’s LAN port, and connect the other
end of the cable to a switch/router, as applicable.
Notes:
A Cognex vision sensor can be directly connected to VisionView VGA•
LAN port.
The VisionView VGA LAN port does not provide Power over Ethernet•
(PoE) to Cognex sensors.
5
3Connect the Touch Screen Cable
(Optional)
If connecting a touch screen to VisionView VGA, connect the Touch1.
Screen cable’s RJ-12 connector to VisionView VGA’s Touch Screen port.
Connect the other end of the Touch Screen cable to the touch screen’s2.
serial connector.
4Connect the USB Accessories (Optional)
If connecting a USB mouse or keyboard to the VisionView VGA, connect a
USB cable to VisionView VGA’s USB port.
5Connect the Power Cable
Verify the 24VDC power supply being used is unplugged and not1.
receiving power.
Attach the power cable’s -24V wire to Pin 2 and the +24V wire to Pin 32.
on the green power connector supplied with VisionView VGA. Connect a
frame ground wire from Pin 1 to frame ground. Tighten the wire retention
screws.
Insert the green connector into the Power Connector port and tighten the3.
connector screws.
Caution: Do not connect AC power directly to the VisionView VGA
Power Connector.
Restore power to the 24VDC power supply and turn it on if necessary.4.
6
VisionView VGA Specifications
Minimum Firmware Version VisionView 1.3.0
Memory System 128MB Mobile SDRAM
Program 128MB non-volatile flash memory
Video 16MB Video SDRAM
Cooling System Fanless Design
I/O Status LEDs Power
USB 1 Host USB 1.1 (12 Mb/sec.) port for basic HID support (mouse and
keyboard) and for saving images to a USB drive1.
Network 1 Ethernet port, 10/100 BaseT, TCP/IP Protocol, Full Duplex. LEDs
indicate Ethernet network activity.
Touch Screen21 Touch Screen port, RS232 serial protocol
Display 1 VGA port
Power Consumption 24VDC ±10%, input current 1A (maximum). VisionView VGA
contains an internal self-resetting fuse.
Mechanical Material ABS/PC blend (V0 UL Rated) housing
Mounting #3 Din Rail (35mm) or four M4 threaded mounting holes
Dimensions 46.0mm (1.81in) x 138.6mm (5.46in) x 156.0mm (6.14in) (with feet)
Weight 454g (16.0 oz.)
7
Environmental Temperature Operating: 0°C to 45°C (32°F to 113°F)
Storage: -30°C to 80°C (-22°F to 176°F)
Humidity 90%, non-condensing (Operating and Storage)
Protection IP20 or NEMA 1
Shock 30 G Shock per IEC 68-2-27.
Vibration 2 G from 10-2000 Hz. Vibration per IEC 68-2-6.
Regulatory Compliance CE, FCC, TÜV SÜD NRTL, RoHS
Power Connector Specifications
1
2
3
Pin # Signal Name
1 Frame Ground
2 -24VDC (Return)
3 +24VDC (Power)
USB drives should be formatted with a FAT32 file system.1.
Refer to the2. VisionView®Software Manual for details on supported touch screens.
8
Touch Screen Port Specifications
6
1
Pin # Signal Name
1 CTS
2 Not Used
3 TxD
4 GND
5 RxD
6RTS
Altri manuali per VisionView
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Scheda video popolari di altre marche
Gainward
Gainward GeForce GTX 690 4GB Manuale utente
ATI Technologies
ATI Technologies RADEON 137-40225-20 Manuale utente
MSI
MSI N220GT series Manuale utente
ATI Technologies
ATI Technologies RADEON 7000 MAC EDITION Manuale utente
SIIG
SIIG aurora Manuale utente
ClearSpeed
ClearSpeed ClearSpeed Advance e720 Manuale utente
