Cole Parmer Masterflex S Manuale utente

OPERATING MANUAL

EASY-LOAD®

PUMP HEADS

®®

A-1299-0377

Edition 16

1-800-MASTE FLEX (627-8373) (U.S. and Canada only)

11 (847) 549-7600 (Outside U.S.) • (847) 549-7600 (Local)

www.masterflex.com • techinfo@coleparmer.com

Thermo Fisher Scientific

1-800-637-3739 (U.S. and Canada only)

11 (847) 381-7050 (Outside U.S.) • (847) 381-7050 (Local)

www.thermoscientific.com • fluidhand[email protected]

EXPLANATION OF SYMBOLS

CAUTION: Risk of danger. Consult the Operator's Manual for

nature of hazard and corrective actions.

CAUTION: Risk of crushing. Keep fingers away from rotor while

pump is in operation. Stop pump before loading or unloading tubing.

SAFETY PRECAUTIONS

WARNINGS: Turn drive off before removing or installing tubing. Fingers

or loose clothing could be caught in the rollers.

Stop the drive when changing the tubing or its position in

the rotor mechanism (the rotor is partially exposed when

the LOADING LEVER is in the open position).

NOTE: Use only MASTERF EX precision tubing with MASTERF EX pumps to

ensure optimum performance. Use of other tubing may void applicable

warranties.

C-FLEX, NORPRENE, PHARMED, TYGON — Reg TM Saint-Gobain Performance Plastics Corp.

Trademarks bearing the ® symbol in this publication

are registered in the .S. and in other countries.

WARNING: PRODUCT USE LIMITATION

This product is not designed for, nor intended for use in patient connected

applications; including, but not limited to, medical and dental use, and

accordingly, has not been submitted for FDA approval.

PUMP FOR LIQUID

ORIGINAL IN TRUCTION

Number of rollers: 3

Maximum pump speed (rpm): 600

Nominal torque load-Running: up to 90 oz-in (6.5 kg-cm)

Housing materials: Polysulfone (PSF) or Polyphenylene sulfide

(PPS), stainless steel (SS), anodized aluminum, nylon

Roller/bearing materials: Cold-rolled steel (CRS)/Cold-rolled steel (CRS) or

Stainless steel (SS)/Sealed stainless steel

Rotor materials: Cold-rolled steel (CRS) or Stainless steel (SS)

Operating temperature ‡ :32°F to 104°F (0°C to 40°C )

Storage temperature: -49°F to 149°F (-45°C to 65°C)

Humidity: 0 to 90% (non-condensing)

Dimensions (W × H × D):

Operating: 49⁄16 in × 4 in × 23⁄16 in

(116 mm × 102 mm × 56 mm)

Open: 49⁄16 in × 513/16 in × 23⁄16 in

(116 mm × 148 mm × 56 mm)

Weight: 1 lb (0.45 kg)

Noise level: <70 dBA @ 1 meter

Compliance (for CE mark):EN809 (EU Machinery Directive)

* As tested with NORPRENE®, PHARMED®BPT and TYGON®tubing. Values will be less with silicone and C-FLEX®.

‡ Use in this temperature range for continuous duty operation with no decrease in performance or product life. Pump

heads will wor outside this range with some possible reductions in performance or product life.

Pump Head no. Pump Material Occlusion haft Length L/ ®Tubing

07518-00 PSF/C S Fixed Short L/S®13, 14, 16, 25, 17, 18

07518-02 PSF/C S Fixed Short L/S®15, 24

07518-10 PSF/SS Fixed Short L/S®13,14, 16, 25, 17, 18

07518-12 PSF/SS Fixed Short L/S®15, 24

07518-20 PSF/C S Fixed Long L/S®13, 14, 16, 25, 17, 18

07518-22 PSF/C S Fixed Long L/S®15, 24

07518-30 PSF/SS Fixed Long L/S® 13,14, 16, 25, 17, 18

07518-32 PSF/SS Fixed Long L/S®15, 24

07518-60 PPS/SS Fixed Short L/S®13, 14, 16, 25, 17, 18

07518-62 PPS/SS Fixed Short L/S®15, 24

07518-80 PPS/SS Fixed Long L/S®13, 14, 16, 25, 17, 18

07518-82 PPS/SS Fixed Long L/S®15, 24

SPECIFICATIONS

L/ ®Flow Rate Max. Discharge Pressure* Vacuum* uction Lift*

Tubing @1 rpm @ 600 rpm psig (bar) @ 600 rpm @ 600 rpm

mL/Rev mL/min in (mm) Hg ft (m) H2O

L/S®13 0.06 36 40 (2.7) 26 (660) 29 (8.8)

L/S®14 0.21 130 40 (2.7) 26 (660) 29 (8.8)

L/S®16 0.80 480 40 (2.7) 26 (660) 29 (8.8)

L/S®25 1.7 1000 35 (2.4) 26 (660) 29 (8.8)

L/S®17 2.8 1700 20 (1.4) 20 (510) 22 (6.7)

L/S®18 3.8 2300 15 (1.4) 20 (510) 22 (6.7)

L/S®15 1.7 1000 40 (2.7) 26 (660) 29 (8.8)

L/S®24 2.8 1700 40 (2.7) 26 (660) 29 (8.8)

Typical Flow, Pressure and Vacuum Data:

INTROD CTION AND GENERAL DESCRIPTION

This /S EASY- OAD®Pump Head when combined with a MASTERF EX®/S®drive

or compatible system is designed to provide a simple easy-to-use peristaltic pump

system. The Pump Head accepts several different tubing sizes for a wide range of

flow rates. The unique over-center cam design and adjustable tubing retention

allows quick tubing changes and greatly reduced maintenance time.

Each pump is supplied complete with a 15 in (38-cm) length of tubing, one

mounting hardware package and this manual. No tools are required to complete

installation.

DRIVE COMPATIBILITY AND SET P

The /S EASY- OAD Pump

Head is compatible with most

MASTERF EX /S drives with a

standard tang interface. Mount

the Pump Head using the 2

screws provided. (See Figure

#1.)

T BE LOADING

1. Be sure the pump drive is

turned off.

2. Rotate the lever to the left

to open the pump.

3. oad tubing of the correct

size. Center the tubing

between the retainers.

(Figure #2.)

4. Rotate the lever to the right

to close. (Figure #3.)

WARNING: Stop the

drive when changing

the tubing or its

position in the rotor

mechanism (the rotor

is partially exposed

when the OADING

EVER is in the open

position).

NOTE: For optimum tubing

life, keep tubing straight where

it enters and exits the pump.

Figure #1. Setup

Figure #2. Open and Load

Figure #3. Close Pump

Mounting Holes

Mounting Bolt

Alignment Holes

Pump Shaft Tang

Motor Shaft

Pins

(On

some

units)

T BE LOADING (cont'd)

5. Adjust tubing retainer.

(Figure #4.)

Release the tubing retainer from its

locked position by pushing it slightly

into the body, then downward and

firmly against the tubing.

Repeat for both sides.

NOTE: Tubing retainers usually do

not need to be readjusted when

changing tubing of the same type

and size.

NOTE: There are a few combinations of tubing and materials that may require a

further adjustment of the tubing retainers if the tubing creeps. Open Pump Head,

move tubing retainer down one (1) notch, then close Pump Head. Turn pump on.

If tubing creep persists, repeat procedure.

M LTI-CHANNEL MO NTING

/S EASY- OAD Pump Heads can be mounted in tandem (up to four) depending

upon the torque capabilities of the drive. (See Figure #5.)

Special mounting hardware is required.

See REP ACEMENT PARTS AND ACCESSORIES for mounting hardware.

CAUTION: DO NOT OVERTIGHTEN SCREWS OR WING NUTS.

NOTE: The /S EASY- OAD Pump Head can be used in any combination with

other /S EASY- OAD II Pump Heads. The longer /S EASY- OAD II mounting

hardware is required (not supplied).

NOTE: The tubing on the inside /S EASY- OAD Pump Head(s) can be changed

without dismantling the outside Pump Head(s) from the drive.

Figure #4. Retainer Adjustment

Figure #5. Multi-channel Mounting

Mounting Holes For

Tandem Units

Mounting Bolts

MAINTENANCE

No lubrication is required for the /S EASY- OAD Pump Head.

See REP ACEMENT PARTS AND ACCESSORIES for parts ordering

information. Contact dealer for further repair information.

Cleaning

Use a mild detergent solution to clean the Pump Head.

Do not immerse, nor use excessive fluid.

Disassembling Pump Head

1. Remove Pump Head from drive.

2. Remove the two screws shown in Figure #6.

Figure #6. Disassembling Pump Head

3. Remove rotor/bearing support assembly.

4. Replace rotor/bearing support assembly and secure with two screws.

NOTE: Screws have a high/low dual thread. Be careful to engage the threads in

the housing properly.

Assembly Screws

REPLACEMENT PARTS AND ACCESSORIES

A. Main body assembly (occlusion bed with rear bearings).

Pump Head no. P F order no. Pump Head no. PP order no.

07518-00, -02, -20, -22 07518-07 ——

07518-10, -12, -30, -32 07518-17 07518-60, -62, -80, -82 07518-67

Pump Head no. hort shaft order no. Pump Head no. Long shaft order no.

07518-00 07518-08 07518-20 07518-28

07518-02 07518-09 07518-22 07518-29

07518-10 07518-18 07518-30 07518-38

07518-12 07518-19 07518-32 07518-39

07518-60 07518-68 07518-80 07518-88

07518-62 07518-69 07518-82 07518-89

B. Rotor/bearing support assembly.

C. Mounting hardware for L/S EASY-LOAD Pump Heads.

Set contains #8-32 screws, washers, and wing nuts

(in 2-, 3- and 4-head hardware).

Number of heads tainless steel

to be mounted order number

107013-04

2 07013-05

307013-08

407013-09

8Printed in U.S.A.

WARRANTY

se only MASTERFLEX precision tubing with MASTERFLEX pumps to

ensure optimum performance. se of other tubing may void applicable

warranties.

The Manufacturer warrants this product to be free from significant deviations from

published specifications. If repair or adjustment is necessary within the warranty

period, the problem will be corrected at no charge if it is not due to misuse or

abuse on your part, as determined by the Manufacturer. Repair costs outside the

warranty period, or those resulting from product misuse or abuse, may be invoiced

to you.

The warranty period for this product is 2 years from the date of purchase.

PRODUCT RETURN

To limit charges and delays, contact the seller or Manufacturer for authorization

and shipping instructions before returning the product, either within or outside of

the warranty period. When returning the product, please state the reason for the

return. For your protection, pack the product carefully and insure it against

possible damage or loss. Any damages resulting from improper packaging are your

responsibility.

TECHNICAL ASSISTANCE

If you have any questions about the use of this product, contact the Manufacturer

or authorized seller.

1-800-MASTE FLEX (627-8373) (U.S. and Canada only)

11 (847) 549-7600 (Outside U.S.)

(847) 549-7600 (Local)

www.masterflex.com

techinfo@coleparmer.com

*EN809 manufacturered by:

Thermo Fisher Scientific

28W092 Commercial Avenue

Barrington, IL 60010

1-800-637-3739 (U.S. and Canada only)

11 (847) 381-7050 (Outside U.S.)

(847) 381-7050 (Local)

www.thermoscientific.com

[email protected]

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cole Parmer Pompa dell'acqua

Cole Parmer

Cole Parmer Mfsterflex I/P Manuale utente

Cole Parmer

Cole Parmer VPS-200 Series Manuale utente

Cole Parmer

Cole Parmer Masterflex L/S 7569-00 Manuale utente

Cole Parmer

Cole Parmer Mastercraft B/T RAPID-LOAD 77111-30 Manuale utente

Cole Parmer

Cole Parmer Barnant Masterflex 07534-04 Manuale utente

Cole Parmer

Cole Parmer Masterflex I/P 77600-62 Manuale utente

Cole Parmer

Cole Parmer Masterflex L/S 77390-00 Manuale utente

Cole Parmer

Cole Parmer Masterflex L/S 07534-04 Manuale utente

Cole Parmer

Cole Parmer Masterflex B/T Rapid-Load Manuale utente

Cole Parmer

Cole Parmer Masterflex 07525-20 Manuale utente

Cole Parmer

Cole Parmer AIR ADMIRAL 79202-00 Manuale utente

Cole Parmer

Cole Parmer Ismatec Mini-S Series Manuale utente

Cole Parmer

Cole Parmer VP-200 Series Manuale utente

Cole Parmer

Cole Parmer Masterflex L/S 77202-50 Manuale utente

Cole Parmer

Cole Parmer 74900-20 Manuale utente

Cole Parmer

Cole Parmer Masterflex Catalyst FH10 Microflex Manuale utente

Cole Parmer

Cole Parmer MasterFlex I/P 77420-00 Manuale utente

Cole Parmer

Cole Parmer 07519-05 Manuale utente

Cole Parmer

Cole Parmer Masterflex L/S 77390-00 Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente