Coleman Air C440-HVAD Manuale utente

C440

HVAD Quick Start Guide

oleman

The C440

HVAD balances the

tried and true with the newest

technologies, resulting in a

super capable diversion

controller for your alternate

energy system that’s easy to

use and even easier to love.

The digital version of the

C440

HVA

•

Fully digital user interface.

• Solenoid based with 3-stage charge control.

• No jumpers or potentiometers need to be set.

• LCD 2 x 16 back-lit display.

• Both manual and automatic equalize modes are available.

• Dual shunts for monitoring both solar and turbine amperage and wattage.

• Automatic nominal battery voltage detection.

• Nearly all charge parameters can be managed through the user interface.

• Relay on time can be controlled and set for diversion times up to several hours.

• Upper and lower set points can both be set.

• Automatic LCD back light dimming to save energy.

• Dual Truck Star breakers, one each for your turbine input and diversion output.

• 12, 24 or 48-volt battery systems.

• Vented cover.

• Modular PCB Layout.

** The solenoid in this unit has been tested to over 440 amps. We have installed two 150-amp breakers as a standard

configuration.

This allows for 9000 watts of wind power in a 48-volt system, 4500 watts in a 24-volt system and 2250 watts in a 12-volt

system.

Solar systems should be designed for no more than 125 amps continuous current. **

/27

/2017

This unit is designed for mounting in a dry indoor environment.

The enclosure will not protect the

contents from moisture. Please do not mount outdoors where rain, snow or high moisture content is a

possibility.

All user settable parameters as well as additional information are

accessible via the user interface which consists of the LCD screen

and the three buttons located on the front cover.

Pressing any key during the normal operation of the unit will cause the

main menu to be displayed. Using the right/left buttons will scroll

through the menu options. Pressing the “Enter” button will cause that

menu option or value to be selected. Use of the up/down menu

increases and decreases the current menu value. Pressing the up

button exits the menu (unless you are currently modifying a value, in

which case it will increase the value. First press “Enter” to select the

current value, and then press the up button to exit the menu).

The Red LED on the front of the unit indicates an error of some

nature. The exact cause of the error will be shown on the LCD screen

(unless you have activated one of the menu options).

The Green LED on the front cover is lighted when the unit is first

turned on and also any time the charge performance is consider

ed high

enough to complete the current charge cycle. If the solar/turbine

power is not adequate to complete the charge cycle, the cycle will be

extended and the mode timer will not count down. When this green

LED is lighted, the charger is able to pass enough current to the

batteries to complete a full charge of the batteries.

The internal LED on the upper left of the large PCB board (motherboard) is lighted

when the solenoid is engaged.

The red LED on the small daughter board is lighted when there has been an over-

voltage detected. To clear an over-voltage condition, all power to the unit must

be disconnected for at least 10 seconds. Once power is re-applied, the unit should

clear the fault. Over-voltage conditions should be addressed by ensuring your

wind turbine and/or solar inputs never exceed 100 volts and both wind and solar

are never enabled without first ensuring the controller is powered up and running

from the batteries.

This is the quick start guide

only.

See http://ColemanAir.us to

download the full instruction

and installation manual.

All connections to the batteries, solar panels and turbines are made to the six terminals on the bottom of the unit. If you will be using a wind turbine, you will need to connect your diversion

load to the two terminals on the left-hand side of the unit. This unit may be used for wind (or hydro) only, solar only or both simultaneously. Multiple solar panels and or wind turbines

may be hooked up as long as you do not exceed the total capacity of the unit. More information on these subjects is provided at http://ColemanAir.us (See: Articles and Information.)

Ensure you have selected adequate sized wire for the amperage you will be controlling. Undersized wire can result in very high heat in the wire and connections possibly leading

to a fire. Always use a fuse or DC disconnect! Hooking up an energy source or diversion load without a fuse or disconnect can result in serious injury or death!

This breakers inside the unit do not disconnect the unit from the battery bank power. The external breaker shown above is required!

Use extreme caution when installing or servicing this controller. High amperages and voltages can KILL you. – Always disconnect the controller before servicing.

Altri manuali per C440-HVAD

Questo manuale è adatto per i seguenti modelli

Altri manuali Coleman Air Controllori