Coleman CHD200 Manuale utente

CHD200 User Manual

1. About Your Trail Camera 

About this Manual

Congratulations on purchasing the Minolta CHD200 Trail Camera!

The contents of this manual are subject to change without notice. Note that the

example screens and product illustrations shown in this User’s Guide may differ

somewhat from the screens and configuration of the actual camera.

This manual contains proprietary information protected by copyright. All rights

are reserved. No part of this manual may be reproduced by any mechanical,

electronic or other means, in any form, without prior written permission of Elite

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1)

This device may not cause harmful interference and

(2)

This device must accept any interference received, including interference

that may cause undesired operation.

RF Exposure Warning

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This equipment must be installed and operated in

accordance with provided instructions and must not be co-located or operating in

conjunction with any other antenna or transmitter. End-users and installers must

1. About Your Trail Camera 

be provided with antenna installation instructions and transmitter operating

conditions for satisfying RF exposure compliance.

FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.4 W/kg

CE Mark Warning

This is a Class B product, in a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

Safety and Handling Precautions

Camera Information

•

Do not disassemble or attempt to service the camera yourself.

•

Do not expose the camera to moisture, or extreme temperatures.

•

Allow the camera to warm up when moving from cold to warm temperatures.

•

Do not touch and put pressure on the camera lens.

•

Do not expose the lens to direct sunlight for extended periods.

•

Do not use abrasive chemicals, cleaning solvents or strong detergents to clean

the product. Wipe the product with a slightly damp soft cloth.

•

Do not use the flash or LED Light near a person's eyes to prevent possible eye

injury.

•

To prevent you from falling over or resulting in traffic accident, please do not use

the camera while you are walking, driving or riding a vehicle.

•

Please handle the camera strap with care, and never place the strap around the

neck of an infant or child. Wrapping the strap around a neck may cause

suffocation.

•

Do not subject the LCD screen to impact.

•

To prevent the risk of fire or electric shock, do not expose this appliance to rain

or moisture.

Battery Information

•

Turn off the camera before installing or removing the battery.

•

Use only the provided batteries or type of battery and charger that came with

your camera. Using other types of battery or charger may damage the device

and invalidate the warranty.

•

Inserting the battery upside down can cause damage to the product and possibly

cause an explosion.

•

When the camera is used for an extended period of time, it is normal for the

camera body to feel warm.

•

Download all pictures and remove the battery from the camera if you are going

to store the camera for a long period of time.

•

The type of battery and the battery power level may cause the lens to be stuck

up. Ensure you use the correct battery type and use a fully charged battery.

•

Risk of explosion if battery is replaced by an incorrect type. Dispose of used

1. About Your Trail Camera 

batteries according to the instructions.

•

Please keep the batteries out of the reach of children to prevent from swallowing

batteries, which might cause poisoning.

•

Once the battery's color changes or its shape is twisted, please stop using it.

USB adapter Information

•

Do not expose the adapter to high temperatures or moisture places. Otherwise, it

may cause fire or electric shock.

•

Do not attempt to repair, disassemble, change or transform the adapter.

•

Avoid sudden changes in temperature, which may cause condensation on the

adapter’s internal surfaces. Please do not use it immediately in this situation.

•

Do not touch the plug with wet hands. Otherwise, it may cause electric shock.

•

Do not use the travel voltage converter or AC/DC power inverter. Otherwise, it

may cause damage, overheating, malfunction or fire to the camera.

2. First Use 

1.1

Camera Interface

1) Lens 9) USB Jack 17) OK/Video Button

2) Infrared LEDs 10) DC Jack 18) Right/Photo Button

3) Indicator Light 11) AV Jack 19) Record Button

4) MIC 12) Speaker 20) LCD Screen

5) PIR Motion Sensor 13) Battery Compartment 21) Latch

6) On Position 14) Menu Button 22) Bracket Mount

7) Setup Position 15) Left Button

8) Off Position 16) Replay Button

[Front View] [Bottom View]

[Inside View] [Isometric View]

2. First Use 5

First Use

2.1

Installing the Batteries

Undo the latch and open the camera.

Insert 4 x AA size batteries. Make sure to insert the batteries in the

direction noted on the camera.

When using a power adaptor (not included), open the rubber seal on the

bottom of the unit and insert the DC plug. Please note when a DC plug is

inserted into the camera, the camera cannot be opened. The plug needs to

be removed first.

2.2

Inserting the Memory Card

Insert the SD memory card (not included) to record and store your videos and

photos. When the battery is low, media stored on the memory card will not be

erased. Please insert the SD memory card by following the steps below:

Undo the latch and open the camera.

Insert the memory card in the slot shown below. Ensure that the metal

contacts are inserted first. Push the memory card in until you hear an

audible click.

The memory card can only be inserted in one way. Do not force the

card in if it will not go in smoothly.

Close the camera door and close the latch.

To remove the memory card, simply push in and the card will eject back out.

NOTE:

xPlease format the memory card before using the camera

(Caution, this will erase all data on the card).

xDo not remove or insert the memory card when recording. It

may damage the card or cause data loss.

xMemory card rating must be Class 10 or above.

2. First Use 

2.3

Powering the Camera On/Off

Open the latch and open the camera. Slide the switch on the bottom of the

camera to the ‘SETUP’ position to set up and test the camera, or to the ‘ON’

position to use the camera as normal.

If the camera’s batteries are low, a “Low Power” message will display on the

screen and it will automatically shut down within a few seconds to prevent

memory corruption or loss.

2.4

Connecting to a Computer

Your camera can connect to a computer to transfer photo and video files for

viewing and editing. Connect the camera by plugging in the small end of the

included USB cable to the USB port on the camera, as shown below, and the

large end into the computer. Once connected slide the switch to SETUP or

OFF and the camera’s screen will show “MSDC” and enter Mass Storage

mode automatically.

2.5

Connecting to a TV

Your camera can connect to a TV to view photo and video files. Connect the

camera by plugging in the small end of the included USB cable to the

camera, as shown below, and the large end into the TV. The camera can

also be connected using an AV cable (not included). Once connected slide

the switch to SETUP or OFF and the camera’s screen will show “MSDC”

and enter Mass Storage mode automatically.

USB

Ϯ. &ŝƌƐƚhƐĞ 

2.6

Using the IR Night Vision Mode

This camera has built-in infrared (IR) LEDs for night vision recording -

giving you the ability to capture photos and videos in a dark environment.

The camera will automatically detect the level of light and if it’s dark the

infrared LEDs will automatically illuminate.

Note:

The photos and videos taken while the IR LED is enabled will be

recorded in black and white.

3. Using Your CamĞƌĂ 

Using the CamHUD

3.1

Camera Setup

Before using the camera it’s important to choose the basic settings. Basic

settings can be changed in the Settings menu. These include date & time,

language and sound options. Power the camera on and slide the switch to

SETUP then press the MENU button to enter the Settings menu. A menu

will display on the screen.

3.1.1 Mode

Your camera can record in 3 different modes, Photo, Video, and Photo &

Video.

In the Settings Menu use the LEFT or RIGHT buttons to select ‘Mode’

and press the OK button to enter the ‘Mode’ submenu.

Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (Photo, Video, Photo &

Video).

3.1.2 Photo Resolution

This function sets the photo resolution. The higher the resolution, the greater

the photo quality and the larger the file size of the photo.

1. In the Settings Menu use the LEFT or RIGHT buttons to select ‘Photo

Resolution’ and press the OK button to enter the ‘Photo Resolution’

submenu.

2. Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (20MP, 16MP, 12MP, 8MP,

5MP, 3MP, 1MP).

3.1.3 Photo Series

This function allows the camera to capture consecutive photos with every

picture taken.

In the Settings Menu use the LEFT or RIGHT buttons to select ‘Photo

Series’ and press the OK button to enter the ‘Photo Series’ submenu.

Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (1 Photo, 2 Photos, 3

Photos).

3.1.4 Video Resolution

This function sets the video resolution. The higher the resolution, the

greater the video quality and the larger the file size of the video.

1. In the Settings Menu use the LEFT or RIGHT buttons to select ‘Video

Resolution’ and press the OK button to enter the ‘Video Resolution’

3. Using Your CamĞƌĂ 

submenu.

2. Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (1920x1080P, 1280x720P,

720x480P, 640x480P).

3.1.5 Video Length

This function lets you set the length of each video recorded. The longer the

video, the larger the file size of the video.

In the Settings Menu use the LEFT or RIGHT buttons to select ‘Video

Length’ and press the OK button to enter the ‘Video Length’ submenu.

Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (3-60 Seconds, 1 Minute, 2

Minutes, 3 Minutes, 4 Minutes, 5 Minutes, 6 Minutes, 7 Minutes, 8

Minutes, 9 Minutes, 10 Minutes).

3.1.6 Audio Recording

This function allows the camera to record audio while recording video.

1. In the Settings Menu use the LEFT or RIGHT buttons to select ‘Audio

Recording’ and press the OK button to enter the ‘Audio Recording’

submenu.

2. Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (On, Off).

3.1.7 Shot Lag

This function sets the amount of time in between pictures. This prevents

the memory card from filling up with too many pictures and videos of the

same event.

In the Settings Menu use the LEFT or RIGHT buttons to select ‘Shot

Lag’ and press the OK button to enter the ‘Shot Lag’ submenu.

Press the LEFT or RIGHT buttons to navigate the menu and press the

OK button to confirm your selected setting (5-60 Seconds, 1-60

Minutes).

3.1.8 Sensitivity Motion Sensors

The sensitivity of the main motion sensor is set here. The sensitivity level

should be based the activity in the area where the camera will be placed.

For interior areas and environments with low activity select ‘High’. For

outside areas and environments with normal activity select ‘Middle’. For

environments with a lot of activity select ‘Low’.

1. In the Settings Menu use the LEFT or RIGHT buttons to select

‘Sensitivity Motion Sensors’ and press the OK button to enter the

‘Sensitivity Motion Sensors’ submenu.

Indice

Altri manuali Coleman Macchina fotografica digitale

Coleman

Coleman 2V7WP Manuale utente

Coleman

Coleman 2V9WP Manuale utente

Manuali Macchina fotografica digitale popolari di altre marche

Mercury

Mercury 350K Manuale utente

Pentax

Pentax Optio LS 465 Manuale utente

Sanyo

Sanyo VPC-S1085 Manuale utente

GE SMART A1255 Manuale utente

Point Grey

Point Grey Gazelle Manuale utente

Nikon

Nikon COOLPIX A Manuale utente

Pentax

Pentax P-5 Manuale utente

BlazeVideo

BlazeVideo A280 Manuale utente

Sony

Sony MCA-20 Manuale utente

Sony

Sony Alpha DSLR-A290 Manuale utente

ATIK Cameras

ATIK Cameras One Manuale utente

CohuHD Costar

CohuHD Costar 3930 Series Manuale utente

Leica

Leica M10-R Manuale utente

FujiFilm

FujiFilm FinePix A700 Manuale utente

Lorex

Lorex LNZ81P25 Series Manuale utente

GE J1470S Manuale utente

Sony

Sony A6700 Guida utente

Canon

Canon EOS ELAN7 Manuale utente