Colortrac SingleSensor CIS Manuale utente
SCIM-003
Colortrac Ltd
Page 1 of 23
Issue 1
SingleSensor Instruction Manual
Date: 12/02/14
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole.
C
Co
ol
lo
or
rt
tr
ra
ac
c
S
SC
C
S
Sc
ca
an
nn
ne
er
r
S
Si
in
ng
gl
le
eS
Se
en
ns
so
or
r
C
CI
IS
S
I
In
ns
st
tr
ru
uc
ct
ti
io
on
n
M
Ma
an
nu
ua
al
l
SC Scanner Instruction Manual
Page 2 of 23
SC Scanners
SC25m, SC25c & SC25e
SC36m, SC36c & SC36e
SC42m, SC42c & SC42e
Instruction Manual
Issue 1
©Colortrac Ltd 2014
The product and the contents of this publication may be changed without prior notification.
Colortrac Ltd makes every effort to ensure this publication is free from error. Misprints, errors
or quality observations should be reported to Technical Support, Colortrac Ltd.
Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the
use of the equipment or this manual.
No part of this product or publication may be reproduced,
copied or transmitted in any form or by any means without
permission from:
Colortrac Ltd.
Units 3 –5 Brunel Court.
Burrel Road.
St Ives,
Huntingdon,
Cambridgeshire,
PE27 3LW.
United Kingdom.
Tel: +44 (0)1480 464618
Fax: +44 (0)1480 464620
www.colortrac.com
SC Scanner Instruction Manual
Page 3 of 23
CONTENTS
1Tools Required ......................................................................................................................... 4
2Photos Information ................................................................................................................... 4
3SingleSensor CIS Assy ............................................................................................................ 5
4Calibration............................................................................................................................... 20
5Auto-stitch............................................................................................................................... 22
SC Scanner Instruction Manual
Page 4 of 23
11
1 Tools Required
To maintain the SC Scanner the tools listed below are required. The tools are generally
available; they are not the responsibility of Colortrac to supply.
1. Wristband
Anti-static and cable.
2. Pencil
HB Lead, or similar
3. 7mm Nutdriver.
To remove and fit M5 nuts.
4. 1.5mm Allen Key
or 1.5mm Hex Key
5. Medium Pozi-drive screwdriver.
PZ1 x 80mm length.
6. Small Pozi-drive screwdriver.
PZ0 x 60mm length.
7. Small Flat Screwdriver
3mm blade x 65mm length (approx.)
8. Medium Flat Screwdriver.
6mm blade (approx.)
9. Pliers.
Flat nosed pliers, short serrated.
2 Photos Information
Some photos in this manual were taken during pre-production, and various stages of the
SC Scanner’s development. Some colours / backgrounds / designs shown may vary from
the actual scanner being worked on. Some background panels may be shown in the
photo to be removed when they actually don’t need to be; however the instructions are
still correct and should be followed as described.
SC Scanner Instruction Manual
Page 5 of 23
3 SingleSensor CIS Assy
1. To remove the Top Lid
Cover, first depress the Lid
Latches at either end of the
Lid Assembly.
2. Allow the Lid Assembly to
gently open.
3. Carefully remove the 2 x M4
screws holding the left end of
the Top Lid Cover. Take care
not to drop the screws while
removing them.
4. Carefully remove the 2 x M4
screws holding the right end
of the Top Lid Cover. Take
care not to drop the screws
while removing them.
SC Scanner Instruction Manual
Page 6 of 23
5. Close the Lid Assembly
making sure both Lid Latches
lock securely.
6. Carefully lift the Top Lid
Cover off from the Lid
Assembly.
7. Remove the Aluminium EMC
Tape covering the cables to
the Main Board.
8. Remove the 4 x M3 screws
holding the Main Board
Cover to the Lid Assembly.
SC Scanner Instruction Manual
Page 7 of 23
9. WARNING: Gently lift the
Main Board Cover to reveal
the Mains Connector.
Release the Mains Connector
from the Main Board.
NOTE: Care needs to be taken with the
Suppressor leads on the Main Board cover as
they can be broken with repeated or excessive
movement.
10. Remove the Main Board
Cover and store in a safe
place.
11. The Main Board cover for the
SC25 is different than for the
SC36 & 24, but should be
removed in the same way as
shown here.
12. Gently lift the locking bar on
each ribbon cable connector.
Don’t use too much force,
which could break the
connector.
SC Scanner Instruction Manual
Page 8 of 23
13. Gently pull the ribbon cable
from the connector.
14. Disconnect the 4 x LED
cables J10 - 13.
15. Remove the M3 x 4 screws
holding the Control Board
Bracket Cover.
SC Scanner Instruction Manual
Page 9 of 23
16. Remove the Control Board
Bracket Cover.
17. Before removing the Control
Board Bracket Assembly, use
a pencil to mark its position.
18. Remove the 4 x M3 screws
holding the Control Board
Bracket Assembly to the Lid
Assembly.
SC Scanner Instruction Manual
Page 10 of 23
19. Rotate the Control Board
Bracket Assembly to gain
access to the Control Board
and cables.
20. Disconnect the 4 x Paper
Sensor Cables and the
Control Board Cable from the
Main Board. Remove the
Control Board Bracket and
store safely until refitting.
21. To raise the lid into the
maintenance position,
remove the 3 x M5 screws
holding the left end Gas
Piston Bracket to the Lid
Assembly, making sure not to
drop them into the scanner.
22. Remove the 3 x M5 screws
holding the right end Gas
Piston Bracket to the Lid
Assembly making sure not to
drop them into the scanner.
NOTE: The End Covers do not need to be
removed.
Indice
