COMBAT Elite Pro Touch Manuale utente

CBT0020 Elite Pro Touch Controller User/Engineer Guide February 2024

Heating Solutions Ltd

Features :

• Wireless air sensor function

• Wireless door switch

• User selectable operating mode

• Temperature and time control

• Energy saving optimum start

• 4 or 6 comfort levels per day

• Temperature hold facility

• Holiday mode

• Key locking

• Frost protection

• Modbus connectivity

Compatible with:

All Single Stage Unit heaters

All Single Stage and Modulating Cabinet heaters

Elite Pro Touch Controller

User & Engineers Guide

Combat Heating Solutions Ltd

Unit 20, Red Mill Trading Estate

Rigby Street

Wednesbury

WS10 0NP

0121 506 7700

Elite Pro Touch

Heating Solutions Ltd

INFORMATION REGARDING UPDATES TO THIS MANUAL ARE LISTED BELOW AND

SHOULD BE NOTED BEFORE COMMENCING WITH ANY INSTALLATION WORK.

Date of Amendment Version Page Description

TECHNICAL UPDATES

CBT0020 Elite Pro Touch Controller User/Engineer Guide February 2024

Heating Solutions Ltd

1 Mode select 4

Change between thermostat and time clock modes 4

2 Power on/off 4

3 Setting the clock (time & date) 4

4 Setting heating time & temperature 5

5 To program the comfort controls 5

6Temperature control 5

7Temperature hold 6

8 Cancel/edit temperature control 6

9 Advance 6

10 Frost Protection 7

11 Locking the Elite Pro Touch 7

12 Unlocking the Elite Pro Touch 7

13 Accessories 8

Pairing accessories 8

Pairing the remote temperature sensor and door contact 8

Viewing accessories 8

Deleting accessories 9

14 Holiday 9

To set a holiday 9

15 Modbus 9

16 Wiring diagram 10

17 General safety when using gas appliances 11

Heating Solutions Ltd

The Elite Pro Touch controller has two modes. The thermostat mode is the default setting

which allows you to set the times you want the heating to be on and what temperature to

heat the site to

1. Thermostat

2. Time clock

The thermostat mode is the default setting.

Change between thermostat mode and time clock modes:

• Press and hold the POWER key for three seconds

• Press and hold the SETUP key for 10 seconds

• Use the LEFT/RIGHT keys to scroll between modes

a. Mode 1 for thermostat

b. Mode 2 for time clock

• Press DONE to conﬁrm

• Press POWER once

The mode select function will reset all parameters (Remote temperature sensors and door

contacts excluded).

The Elite Pro Touch can be turned off completely; while it is off, it will not control the heater

or communicate with any connected accessories (Remote temperature sensors and door

contacts).

• To turn off the Elite Pro Touch, press and hold POWER key for at least 3 seconds.

The display and heat output will turn off.

• To turn the Elite Pro Touch back on, press the POWER Key.

Set the clock;

• Press and hold POWER for 3 seconds

• Press CLOCK

• The ﬁrst hour digit will ﬂash

• Press the UP/DOWN keys to set the hour

• Press the NEXT to set the minutes

• Repeat the above to set the date, month, and year

• Press DONE and then POWER to return to the home screen

1. MODE SELECT

2. POWER ON/OFF

3. SETTING THE CLOCK (TIME AND DATE)

CBT0020 Elite Pro Touch Controller User/Engineer Guide February 2024

Heating Solutions Ltd

The thermostat has three program modes: Weekday/Weekend, 7-day and 24-hour

programming. There is also a manual programming option.

• For Weekday/Weekend programming, the four comfort levels are the same for Mon-

Fri but can be different for Sat-Sun.

• For 7-day programming, each day of the week can have four different levels.

• In 24-hour mode, all days are programmed with the same comfort levels.

The thermostat is supplied with factory-programmed comfort levels; these can be

changed easily. The default times and temperature settings are:

07:00 - 21°C (Wake), 9:00 - 16°C (Leave), 16:00 - 21°C (Return), 22:00 - 16°C (Sleep)

Unused levels must be set to --:-- so that the thermostat will skip these and continue to

the next programmed time. To do this, set the time to 00:00 and press UP/DOWN keys.

• Press the EDIT key

• Use the DAY key to select the day/period of the week (the selection will ﬂash)

• Press NEXT to conﬁrm selection

• WAKE will now ﬂash, and the current time and temperature settings will be shown

• Use the UP/DOWN key at the top to set the hours and minutes

• Use the UP/DOWN key in the centre to set the temperature

• Press the RIGHT arrow key

• LEAVE will ﬂash, displaying the current settings

• Repeat these steps above to set all comfort levels

• For any unused periods, set time to --:--

• Press DONE to conﬁrm and save the settings

You can program up to a maximum of 6 levels. Enable this in the feature menu.

The UP/DOWN keys allow you to adjust the set temperature; when either key is pressed,

you will see the SET TEMP and the desired temperature value. Press DONE to conﬁrm

the temperature setting and return to the main display.

Press the UP/DOWN key to cancel this override, then CANCEL.

4. SETTING HEATING TIME AND TEMPERATURE

5. TO PROGRAM THE COMFORT LEVELS

6. TEMPERATURE CONTROL

Heating Solutions Ltd

The temperature hold function allows you to manually override the current operating

program and set a different temperature for the desired period.

• Press the HOLD once

• Use UP/DOWN to set the desired HOLD time (hours)

• Then Press NEXT

• Minutes will now ﬂash

• Use the UP/DOWN keys to set the desired HOLD time (minutes)

• Use the UP/DOWN keys to set the desired HOLD temperature

• Press DONE to conﬁrm selection

You will see the HOLD LEFT indication displayed on the screen. The time will countdown

the set duration and then revert to the normal program.

• Press the HOLD key once

• Press CANCEL to cancel the HOLD and return to normal operation

• Alternatively, press the EDIT key to adjust the current HOLD settings

This feature allows the next comfort level setting to be brought forward and become active

before its pre-programmed time. Multiple advances are not allowed.

To enable Advance:

• Press the ADVANCE key once

• ADVANCED UNTIL time and the SET temperature will now be displayed

• Press DONE to conﬁrm selection

• To view the SET temperature during Advance, tap either the UP/DOWN key once.

• Press DONE to exit

• To change the SET temperature during Advance, use the UP/DOWN keys followed

by DONE to conﬁrm.

To cancel Advance:

Press the Advance key once, then press CANCEL

7. TEMPERATURE HOLD

8. CANCEL/EDIT TEMPERATURE CONTROL

9. ADVANCE

CBT0020 Elite Pro Touch Controller User/Engineer Guide February 2024

Heating Solutions Ltd

The frost icon will toggle ON/OFF each time the POWER key is pressed. In this mode,

the thermostat will display the frost icon and only turn the heating ON should the room

temperature drop below the set frost temperature. The ﬂame symbol will be displayed if

the heating is turned ON in frost mode.

To cancel the frost protection mode, press the key again.

The thermostat has a keypad lock facility. To activate the lock:

• Press and hold the HOLD key for 3 seconds

• The display will show 0000. At this point, enter a four-digit PIN

• Use the UP/DOWN keys to set the ﬁrst two digits

• Press NEXT

• Use the UP/DOWN keys to set the next two digits

• Press DONE

The display will return to the main screen and display the keypad lock indicator.

Note: The keypad lock indicator is only displayed when the lock is active.

To unlock the thermostat, press any key once:

• The display will show 0000.

• At this point, enter the four-digit PIN you set previously.

• Use the UP/DOWN keys to set the ﬁrst two digits

• Press NEXT

• Use the UP/DOWN keys to set the next two digits

• Press DONE

The display will unlock and return to the main screen.

10. FROST PROTECTION

11. LOCKING THE ELITE PRO TOUCH

12. UNLOCKING THE ELITE PRO TOUCH

Heating Solutions Ltd

The Elite Pro Touch can be paired with remote temperature sensors and door contacts.

Pairing accessories:

Sixteen accessories can be paired with a single Elite Pro Touch Thermostat.

Remote temperature sensor:

When a remote temperature sensor is paired to the thermostat, the thermostat will take

an average between all the remote temperature sensors attached and the temperature

sensor built into the thermostat; this temperature will be displayed.

Door contact:

The thermostat will automatically activate frost protection mode if any door contacts are

broken.

A door icon will be displayed, indication frost protection has been activated.

Pairing the remote temperature sensor and door contact.

• Press and hold the POWER key for 3 seconds

• Press the SETUP key

• Press the DOWN key until the letter P is displayed on the top right of the screen

• The thermostat will start a 99-second countdown; during this countdown, multiple

sensors can be added

• On the remote temperature sensor or door contact, hold the button down for 5

seconds; the red LED will turn on to indicate it is trying to pair with the thermostat.

• When the red LED turns off, the accessory is paired with the thermostat

• The thermostat will display 01:P indication that one accessory has been paired

Viewing accessories:

• Press and hold the power key for 3 seconds

• Press the SETUP key

• Press the DOWN key until the letter A is displayed on the top right, and then press

• A:01 shows the accessory ID number.

• Use the UP and DOWN keys to scroll through the list of attached accessories

If a remote temperature sensor is selected, its sensing temperature will be displayed; if a

door contact is selected, its current state (open or closed) will be displayed.

A batter symbol will be displayed if the accessory has a low battery.

13. ACCESSORIES

CBT0020 Elite Pro Touch Controller User/Engineer Guide February 2024

Heating Solutions Ltd

Deleting accessories:

• On the accessory, press and hold the reset button for 15 seconds; the red LED will

ﬂash three times to indicate the accessory has been reset.

• On the thermostat follow the Viewing Accessories steps

• Press the UP/DOWN keys to view the accessory the needs to be deleted

• Press and hold the DONE key for 10 seconds

In time clock mode, the timed output will be turned off during the holiday period and then

returned to the programmed settings once the holiday period ﬁnishes.

In thermostat mode, the holiday function reduces the set temperature to the frost mode

temperature setting conﬁgured in the setup menu.

The thermostat will maintain this temperature for the duration of the holiday and will then

automatically return to the program mode on your return.

To set a holiday:

• Press the HOLIDAY key once

• Enter the return time (hours) by using the UP/DOWN keys, then press NEXT to

conﬁrm

• Enter the return time (minutes) by using the UP/DOWN keys, then press NEXT to

conﬁrm

• Repeat these steps to set Day, Month and Year

• Press DONE to conﬁrm

The display will now show a plane symbol and indicate frost protection active. To view

or change the set frost temperature while in holiday mode, press the UP/DOWN keys

followed by DONE to conﬁrm

Modbus interface allows the thermostat to be controlled via a building management

system (BMS).

A maximum of 32 devices can be connected to a single RS485 adapter. It is

recommended that a foil twisted pair (FTP) cable is used for the Modbus connections

All Modbus connections should be daisy-chained rather than wired in a star formation

If the thermostat is the last Modbus device on the end of the chain, move the toggle

switch on the back of the fascia to the ON position

15. MODBUS

14. HOLIDAY

Heating Solutions Ltd

16. ELITE PRO TOUCH WIRING DIAGRAM (Elite Pro Unit Heaters)

Indice

Altri manuali COMBAT Controllori

COMBAT

COMBAT Enercal Space 10 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente