Comcast XCAM2 Manuale utente
XCAM2 + XW4
User’s Guide
i
Table of Contents
CHAPTER 1 INTRODUCTION.............................................................................................. 1
Overview ............................................................................................................................ 1
Physical Details - xCam2................................................................................................... 2
Physical Details - XW4...................................................................................................... 4
Package Contents .............................................................................................................. 5
CHAPTER 2 BASIC SETUP ................................................................................................... 6
System Requirements........................................................................................................ 6
Installation ......................................................................................................................... 6
Wall Mounting................................................................................................................... 9
Installation Guidance ...................................................................................................... 11
APPENDIX A SPECIFICATIONS........................................................................................ 12
Spec................................................................................................................................... 12
Regulatory Approvals ..................................................................................................... 13
Disposal Instructions ....................................................................................................... 14
Manufacturer Contact Information............................................................................... 14
Label Information ........................................................................................................... 14
Copyright ©2016. All Rights ReSCrved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
ii
1
This Chapter provides information of the xCam2 's features, components and
capabilities.
Overview
Congratulations on the purchase of your new xCam2 . The xCam2 is a True Day/Night IP
camera that features high definition 1920 x 1080p video resolution and 802.11ac WiFi
connectivity.
Features
•
Standalone Design.
The xCam2 is a standalone system with built-in CPU and Video
encoder. It requires only a power source and a connection to your touch screen.
•
Dual Video Compressions.
The xCam2 supports H.264 and MJEPG video for different
image compressions. The Video support High definition (1080p) resolution with 125Ʊ
viewing angle.
•
Suitable for Home, Business or Public Facilities
. Whether for Home, Business or
Public Facility surveillance, or just for entertainment and fun, the xCam2 has the features
you need.
•
IR LED Support.
Each xCam2 has two infrared LED. The LEDs can provide
illumination around 5 meters long that can help to output a better video quality while
under low-light conditions such as indoors, on cloudy days, or in the morning or evening.
Wireless Features
•
Supports 802.11bgnac Wireless Standard.
The xCam2 product is an 802.11ac
2T2R MU-MIMO device with a dual-band dual-concurrent 2.4GHz and 5GHz radio
2
Physical Details - xCam2
Front - xCam2
Figure 1: Front Panel
IR LEDs IR LEDs provide illumination at night or in a dark environment.
Light Sensor It supports light sensor to provide automatic day/night mode
transition.
Lens No physical adjustment is required or possible for the lens, but you
should ensure that the lens cover remain clean. The image quality is
degraded if the lens cover is dirty or smudged.
POWER indicator
(Blue/White)
On (Solid Blue) - The xCam2 is working normally.
Flashing (Slow Blink White) - The xCam2 is in WPS mode.
Flashing (Double Blink White) - The xCam2 is connected to router
and ready to pair.
2-Way Voice (Slow Blink Blue) – Someone is talking
On (Solid Amber) - The xCam2 is not connected to a router or has
trouble connecting.
Microphone hole
Light sensor hole
3
Rear - xCam2
Figure 2: Rear Panel
RJ-45 Jack This RJ-45 connector is used for power connection when the camera
is under wireless mode. A customized PoE (Power over Ethernet)
splitter.
Reset Button When pressed and released the reset button, the xCam2 will reboot
(restart).
To restore the factory default values:
1. Power On.
2. Keep holding the reset button down for 5 seconds.
3. Release the reset button, the xCam2 is now using the factory
default values.
Microphone The built-in microphone is located on the front of the device.
Speaker The built-in speaker is located on the rear of the device.
4
Physical Details - XW4
XW4
LAN Port To be connected to the RJ-45 jack of xCam2 for power feed and
data exchange.
Reset Button This button has the following function:
•Reset to manufacturer default valued and reboot. When
pressed and held over 5 seconds, the settings of the XW4 will
be set to their default values.
WPS Button Push the WPS button on the device and on your other wireless
device to perform WPS function that easily creates an encryption-
secured wireless connection automatically.
POWER indicator
(Blue/White)
On (Solid Blue) - The XW4 is working normally.
Flashing (Slow Blink White) - WPS association is in process.
Flashing (Double Blink White) - The XW4 is connected to a router.
On (Solid Amber) - The XW4 is not connected to a router or has
trouble connecting.
5
Package Contents
The following items should be included in the package: If any of these items are damaged or
missing, please contact your dealer immediately.
xCam2 Unit (with Stand and Ethernet RJ-45 pigtail) * 1
Screw/Anchor x 2
Screw diameter: 3.5 ; Length: 25mm
Anchor inner diameter: 2.9mm ; Length: 30mm
XW4 Unit * 1
6
This Chapter provides information on how to install and configure the
xCam2 .
System Requirements
•To use the Wireless interface on the wireless model, other Wireless devices must be
compliant with the IEEE802.11abgnac specifications. All Wireless stations must use
compatible settings.
Mode: Infrastructure
SSID: ANY
Wireless Security: Disabled
Domain: USA
Channel No.: Auto
Installation
You must complete the following installation procedure when using the xCam2 for the first
time.
Step 1 - Adding an xCam2 to your network
Make sure the Router and the Touch Panel are both powered on and synchronized before
adding your xCam2 . This step is required when an xCam2 is used for the FIRST time. It only
needs to be done ONCE in order to configure the wireless settings for the xCam2 .
Note: Skip this section if the xCam2 has been set up already.
On the Touch Panel, click on setting icon on the home page.
2.
Enter the ΗMasterΗcode.
3. Enter the "Technical code/ID", then click the "Done" button.
4. Select "Home Devices". Then choose "Cameras-> Add a Camera".
5. Click the "Next" button to check network.
Questo manuale è adatto per i seguenti modelli
1
Indice
