Comet SP015M Manuale utente

Specification are subject to change without notice ie-wfs-SP015-04

SP015, SP015M, SP015C

Batteries holder with connection adapter

DESCRIPTION AND APPLICATION

The Batteries holder is designed to be used as an accessory for battery powered transducers with

radio output to Sigfox net (from Wx8xx series*). It allows you to power the transducer from one or two

3.6V lithium batteries, size "C", thus extending up to six times the operating time compared to the

standard life of size "AA" internal battery. It is equipped with a connection adapter that is mounted in

place of the transducer's internal battery. The SP015 Batteries holder is suitable for applications

where the life of the transducer's internal battery is insufficient and the mains power supply (with

optional accessories) cannot be used.

*) Applicable to W0810, W0811, W0832, W0850, W3810, W3811, W7810 models.

SAFETY NOTICE

use only recommended batteries in the device

never mix different manufacturers' batteries or new ones with those already in use

do not short circuit output of the device, the batteries will be destroyed

always insert batteries with the correct polarity, never with the reversed polarity

do not exceed the specified operating temperatures

device contains electronic parts that must be disposed of in accordance with local

and currently valid legal conditions

POWER SUPPLY BATTERIES

SP015 Batteries holder is supplied separately, without batteries. It is designed for primary lithium

batteries 3.6V, size "C". We recommend using Tadiran SL2770/S batteries (order code A4206). One

or two batteries can be fitted. If you choose to use two batteries, always use batteries the same type

and manufacturer, origin from same delivery, ie. same age. Always use new, unused batteries. It is

forbidden to combine batteries from different manufacturers or to mix new batteries with those already

in use.

Battery life values table for operating temperatures up to + 35 ° C:

sending interval:

10 min

20 min

30 min

1 h

3 h

6 h

12 h

24 h

1 pc battery

1 year

2 years

3 years

5 years

10 years

> 10

2 pc batteries

2 years

4 years

6 years

10 years

> 10

Use two batteries only in applications where the transducer will be set to shorter sending intervals

(from 10 min to 1 h). For long sending intervals (3 h or longer), you can achieve a life of 10 years or

more at normal operating temperatures, even with one battery. Battery life of more than 10 years is

rather theoretical, because at such a long time the effect of batteries self-discharge may be higher

than the power consumption of the device.

At continuous operating temperatures above 35 °C, the battery life may drop by a third or half. In

accordance with the transducer manual, the battery life values apply when extraordinary alarm

messages are not used or only exceptionally.

- 2 -

OVERVIEW OF INDIVIDUAL MODELS

SP015

The transducer and the Batteries holder are placed

on top of each other and screwed together. The

complet is fastened with two suitable screws

according to the type of base material.

Suitable for applications where greater assembly

depth does not matter and for any base material.

SP015M

The transducer and the Batteries holder are placed

on top of each other and screwed together. The

complet is attached with two strong, neodymium

magnets.

Suitable for applications where the greater

assembly depth does not matter and the base

material is metal (magnetic). Allows you to easily

move the complet. Unsuitable for publicly

accessible areas - danger of theft.

SP015C

The Batteries holder is supplied without additional

fastening mechanisms. Together with the

transducer, they can be placed next to each other

and fastened with four suitable screws according

to the type of base material.

Suitable for applications where a smaller assembly

depth is required and for any base material.

The SP015C Batteries holder and transducer can

also be screwed together through the rear walls

over a mounting bracket that holds the assembly in

the application used.

Suitable for applications where the assembly is

placed in a space with a suitable application

holder. The distance from the walls allows more

accurate measurement of temperature or humidity.

This assembly mounting is used, for example, for

installation in a COMETEO F8000 radiation shield.

- 3 -

PUTTING DEVICE INTO OPERATION

1) Mounting the connection adapter on the transducer

unscrew the four screws at the corners of the

transducer case and remove the cover

if you have a new transducer, install it according to the

transducer manual (keep it working from the supplied

battery). After the adapter is mounted, the

Configuration button inside the device will not be

accessible - therefore, before continuing, make sure

that the device is turned on and that you do not

require accelerated transducer parameter settings.

remove the battery by pulling on its handle from the

ready transducer

insert one SP015 connection adapter contact into the

Wx8xx transducer battery contact field. Then insert

the second contact into the other the transducer

battery contact field and close the cover. The contacts

of the two devices must fit exactly together.

verify that the connection adapter is flush with the

transducer housing circuit. If not, remove the adapter

and repeat the assembly procedure. Under no

circumstances should you attempt to force the adapter

and transducer into the correct position.

if the adapter is in the correct position, screw it with

the original screws

keep the original cover and battery for case the

adapter is will removed

- 4 -

2) Battery installation

unscrew the four screws at the corners

of the Batteries holder case and

remove the cover

depending on the required life (see

table above), insert into the Batteries

holder one or two a 3.6V lithium

batteries (of the same type and

manufacturer) with polarity as shown

on figure. Push the battery against

the spring of negative contact and then

release it. Display of the transducer

must light up within 10 seconds and

the transducer will start working.

screw the batteries holder cover. Make sure that the contact surfaces of gasket are free of dirt.

3) Assembly and fixing of the assembly

SP015

screw the transducer onto the holder posts

(1) with the supplied M4 screws

screw all the assembly on the selected

measuring place (2). Observe the

installation instructions and location rules in

the transducer manual. Depending on the

type of material on which the entire

assembly will be mounted, use two suitable

4 mm diameter screws.

SP015M

screw the transducer onto the holder posts

(1) with the supplied M4 screws

attach all the assembly on the selected

measuring place on a metal (magnetic)

base material (2). Observe the installation

instructions and location rules in the

transducer manual.

- 5 -

SP015C

if you want to arrange both devices side

by side, screw the holder to the left side

of the intended transducer position.

Depending on the type of material on

which the entire assembly will be

mounted, use four suitable 4 mm

diameter screws.

if you want to place both devices freely

in the space, screw them together with

the rear walls over a suitable application

holder (not included) using M4 screws

of suitable length

for installation in the COMETEO F8000

radiation shield, screw the two devices

together with the rear walls over the

mounting bracket that is part of the

shield. See instructions for using the

shield. Use the M4 screws from the

SP015C holder package.

BATTERY REPLACEMENT

for models SP015 and SP015M: If it is necessary

to replace the batteries in the Batteries holder

directly at the installation site, first unscrew the

transducer from the holder posts (2 M4 screws)

and move it to the right of the Batteries holder.

Temporarily attach the transducer with only one

screw to the right post of the Batteries holder as

shown. Do not let the transducer hang by the

power cord.

for all models: Remove the four screws at the

corners of case the Batteries holder and remove

the cover. Replace the batteries with new ones

and reassemble all the assembly in reverse.

- 6 -

TECHNICAL PARAMETERS

recommended batteries: Tadiran SL2770/S, lithium, 3.6 V, size "C"

output voltage: 3.6 V DC

continuous output current: max. 200 mA

short circuit protection of output: no (recommended batteries are not dangerous in the event of a short circuit)

power output: connection adapter for transducers Wx8xx

working position: vertically, cable gland down

IP class: IP65 (after mounting the connection adapter to the Wx8xx sensor)

operating temperature: -30 to +60 °C

weight without batteries: 200 g (including connection adapter)

maximum dimensions: SP015 120 x 93 x 43 mm

SP015M 108 x 93 x 48 mm

SP015C 89 x 93 x 40 mm

DEVICE DIMENSIONS

SP015

- 7 -

SP015M

SP015C

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Comet Rack e supporto

Comet

Comet SP015 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente