CommScope SYSTIMAX 360 iPatch 1100 Manuale utente

SYSTIMAX 360™iPatch®1100 Type Panel

Instruction Sheet

Material ID 860 458 413

Issue 1, May 2009

ACN 107 198 425

The iPatch System is covered by U.S. patents 6285293 and 6522737,

and other U.S. and foreign patents and patents pending.

The SYSTIMAX 360™ iPatch®1100 Type Panel is a

SYSTIMAX approved product. This patch panel can be

used in an iPatch System for both EIA-T568A or

EIA-T568B wiring applications. Both 24-port and

48-port versions are available.

Important Safety Instructions

To reduce the risk of fire, electric shock, and injury to persons,

read, understand, and adhere to the following instructions as well

as any warnings marked on the product.

!CAUTION

Remote risk of electric shock.

Never install the product in wet locations or during lightning

storms.

Never touch uninsulated communication wires or terminals.

Note: All wiring that connects to this equipment must meet

applicable local and national building codes and network wiring

standards for communication cable.

Save these instructions.

Specifications

Wire Termination

Wire Size: 22–24 AWG (0.64–0.51 mm) solid copper

22–24 AWG (0.64–0.51 mm) 7-stranded copper

Insulation Size: 0.042 inch (1.07 mm) maximum DOD

Insulation Type: All plastic insulants

(including PVC, irradiated PVC, polyethylene,

polypropylene, PTFE polyurethane, nylon, and FEP)

Reterminations

IDC Contact: 200 minimum

Modular Jack: 750 minimum

Environmental Data

Temperature

Range:

-40ºF to 158ºF (-40ºC to 70ºC) (storage)

23ºF to 122ºF (-5ºC to 50ºC) (operational)

Humidity: 95% noncondensing

2After cabling each panel, assemble and install the rear cable

support on each panel (Figure 7):

aSnap the 4 cable troughs onto the cable support bar.

bInsert the 4 cable straps into the slots in the cable troughs.

cInstall the cable support bar on the back of the panel.

Note: For 2U panels, assemble and install two cable supports.

3Route the cables into the cable troughs. Use the cable straps to

loosely retain the cables (Figure 8).

How To Contact Us

To find out more about SYSTIMAX®Solutions, visit us on the web

at www.commscope.com/systimax

For technical assistance regarding SYSTIMAX products:

Within the United States, contact your local account

representative or CommScope Technical Support at

1-800-344-0223.

From outside the United States, contact your local account

representative or Authorized BusinessPartner.

Figure 7 Installing Cable Supports

Figure 8 Routing and Retaining the Cables

Cable support bar

Cable trough

Cable strap

Slot

Cable support bar

Cable trough

Cable strap

Instruction Sheet:

SYSTIMAX 360™ iPatch®1100 Type Panel

Installing Panels

1Panels are shipped with the cabling labels for B wiring already

installed. If the installation uses A wiring, insert the cabling

labels for A wiring in the slots on the back of the panels. Make

sure that the labels are oriented with the right side up (Figure 1).

2Make sure that the panel bus jumpers are firmly connected to

the panels (Figure 2).

3Install the panels on the rack using the 4 screws provided

(Figure 3). Be careful not to pinch the panel bus jumpers

between the panels and the rack.

4Snap the decorative bezels onto the front of the panels.

(Figure 4).

5Remove the adhesive backing from the cable retainers on the

panel bus jumpers.

6Connect the panel bus connector on each jumper to the

nearest connector on the panel bus, folding the jumper as

shown (Figure 5). Press the cable retainers against the rack.

Figure 1 Inserting the Cabling Label

Figure 2 Checking the Panel Bus Jumper

Figure 3 Mounting the Panels

Figure 4 Installing the Decorative Bezel

Cabling label

Check the panel bus jumper here.

Mounting screws

Decorative bezel

Note: The connector is keyed. The polarized tab on the jumper

connector fits into the opening in the header connector on the

panel bus.

Important:

For 2U panels, connect both panel bus jumpers.

Cabling Panels

Figure 6 identifies the IDC (position) numbers and pair numbers for

cabling panels. Table 1 indicates the conductor colors for

EIA-T568A and EIA-T568B wiring applications.

1Cable each panel. Use a Termination Manager to terminate

each 4-pair cable, following the Termination Manager

installation instructions provided with the panel.

Note: The Termination Manager provides pair-twist control and

strain relief features to the rear termination area of the panel.

continued

Figure 5 Connecting and Routing the Panel Bus Jumpers

Figure 6 Cable IDC Numbers and Pair Numbers—Rear View of Panel

Table 1 Cable Terminations

IDC# A Wiring B Wiring

1W/BL W/BL

2 BL/W BL/W

3W/G W/O

4G/W O/W

5W/O W/G

6O/W G/W

7W/BR W/BR

8 BR/W BR/W

Panel bus

Fold the panel bus

jumper as shown.

Panel bus

Panel bus jumper

Cable retainer

Cable

retainer

Polarized tab

Panel bus

jumper

Pair Numbers

Position Numbers

Pair Numbers

A Wiring B Wiring

Indice

Altri manuali CommScope Pannello di controllo

CommScope

CommScope SYSTIMAX 360 1100GS3 Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche