CommScope PRO-CRIMPER III Manuale utente

Figure 1

PRO–CRIMPER III Hand Tool Assembly 58560–1

consists of Die Assembly 58560–2, and hand tool

frame 354940–1. The die assembly consists of an

insulation stuffer, housing support, housing guides,

die retaining pins, and mounting hardware.

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full crimping. The tool

frame holds a die assembly with insulation and

contact stuffers.

The die assembly features an insulation stuffer, a wire

stuffer, a housing support, housing guides, die

retaining pins, and die retaining screws which secure

the die set in the tool frame. Attached to the outside

of the frame are the housing guides. A nut is used on

the lower die retaining screw to secure the housing

guides in place.

JAN 2017 B

CommScope

To obtain information on CommScope®

products, visit our website

http://www.commscope.com/SupportCenter/TechnicalSupport.aspx

This product is covered by one or more U.S.

patents or their foreign equivalents. For patents, see

www.commscope.com/ProductPatent.aspx

1 of 4

1-800-830-5056.

Technical Assistance Center (TAC) at 1-800-830-5056.

Figure 2

1. Close the tool handles until the ratchet releases,

and allow the handles to open fully. Remove the

nut and both die retaining screws from the tool

jaws.

2. Place the insulation/wire stuffer assembly as

shown in Figure 2. Insert short die retaining pins

and short die retaining screw through the tool

frame, and tighten the screw.

3. Place housing support in the moving jaw of the

tool frame as shown in Figure 2. Mount right hand

housing guide using long die retaining pins, and

secure with long die retaining screw. Mount left

hand housing guide and tighten nut.

4. To disassemble, close the tool handles until the

ratchet releases, remove nut, screws, housing

guides, retaining pins, housing support, and

insulation/wire stuffer assembly.

Before proceeding, Ensure that cable and plug are

compatible, and that cable polarity is correctly

maintained for your specific application.

Refer to Figure 1 and select cable of the specified

size and type. Strip the cable jacket to the length

indicated, taking care not to nick or cut wire

insulation. Proceed as follows:

1. Insert cable into plug until cable is fully

bottomed.

2. Hold the tool so that the back is facing you.

Squeeze the tool handles together and allow them

to open fully.

3. Insert plug assembly fully into die cavity until

plug bottoms in die cavity.

4. Squeeze handles until ratchet releases, and

remove terminated modular plug cable assembly.

5. Check the crimp height as described in Section

5, CRIMP HEIGHT INSPECTION. If necessary,

adjust the crimp height as described in Section 6,

CRIMP HEIGHT ADJUSTMENT.

Figure 3 shows a cutaway of a typical terminated plug

and the required location of the conductors. A visual

inspection through the plastic housing of the plug

should reveal whether the conductors are within the

acceptable range.

Figure 3

Inspect connector for proper crimp height using an

indicator with needle–point probes. Refer to Figure 3

for correct crimp height measurement. If necessary,

adjust the crimp height as described in Section 6,

CRIMP HEIGHT ADJUSTMENT.

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel

from the opposite side of the tool.

3. Observe the ratchet adjustment wheel; if a

tighter crimp is required, rotate the adjustment

wheel COUNTERCLOCKWISE to a

higher–numbered setting. If a looser crimp is

required, rotate adjustment wheel CLOCKWISE to

a lower–numbered setting.

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, secure the

lockscrew. If the dimension is unacceptable,

continue to adjust the ratchet, and again measure

a sample crimp.

If correct crimp height cannot be obtained, tool and or

dies must be replaced See Section 8, PARTS

REPLACEMENT.

CommScope recommends that operators of the

tool be made aware of, and responsible for, the

following steps of daily maintenance:

1. Remove dust, moisture, and any other

contaminants from the tool with a clean, soft brush,

or a clean, soft, lint–free cloth. Do NOT use hard or

abrasive objects that could damage the tool.

Figure 4

2. Make certain that the retaining pins are in place

and that they are secured with retaining rings.

3. All pins, pivot points, and bearing surfaces

should be protected with a thin coat of any good

SAE 20 motor oil. Do not oil excessively.

4. When the tool is not in use, keep handles closed

to prevent objects from becoming lodged in the

crimping jaws. Store the tool in a clean, dry area.

Regular inspection of the tool should be performed by

quality control personnel. A record of scheduled

inspections should remain with the tool or be supplied

to supervisor personnel responsible for the tool.

Inspection frequency should be based upon amount

of use, working conditions, operator training and skill,

and established company standards.

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 8, PARTS REPLACEMENT.

1. Remove all lubrication and accumulated film by

immersing the tool (handles partially closed) in a

suitable commercial degreaser that will not affect

paint or plastic material.

2. Make certain that all retaining pins are in place

and secured with retaining rings.

3. Close tool handles until ratchet releases and

then allow them to open freely. If they do not open

quickly and fully, the spring is defective and must

be replaced. See Section 8, PARTS AND

REPLACEMENT.

4. Inspect the tool frame for wear or damage,

paying particular attention to the tool jaws and

pivot points. If damage is evident, refer to Section

8, PARTS REPLACEMENT. If tool is acceptable,

lubricate and return to service.

5. Check the crimping dies occasionally to make

sure dies are not broken or chipped. If damage is

evident, refer to Section 8, PARTS

REPLACEMENT.

Customer–replaceable parts are shown in Figure 1.

Available separately, PRO–CRIMPER III Hand Tool

Repair Kit 679221–1 includes a replacement nut and

a variety of pins, rings, screws, and springs. If the

dies are damaged or worn excessively, they must be

replaced. Order the repair kit and replaceable parts

through your CommScope representative, or call

1–800–830–5056, or send a facsimile of your

purchase order to 1–800–830–5056, or write to:

Technical Assistance Center (TAC)

COMMSCOPE, INC.

www.commscope.com

Email: TAC.Americas@commscope.com

Revisions to this instruction sheet include:

•Rebranded to CommScope

Questo manuale è adatto per i seguenti modelli

Altri manuali CommScope Utensili elettrici

CommScope

CommScope PRO-CRIMPER III Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale