Comnet CNFE2MC2C/M Manuale utente

INSTALLATION AND OPERATION MANUAL

CNFE2MC2C[/M]

10/100MBPS ETHERNET ELECTRICAL TO OPTICAL

MEDIA CONVERTER WITH CONTACT CLOSURE RELAY

v1.0 Jan 2012

The ComNet™ CNFE2MC2C[/M] Ethernet 10/100Mbps Ethernet media converter is

designed to transmit and receive 10/100 Mbps data and bi-directional contact relay

over multimode or single mode optical fiber using sold-separately Small Form-Factor

Pluggable (SFP) modules to select distance and connector type. The electrical interface

will Auto-Negotiate to a 10 Mbps, or 100 Mbps Ethernet rate without any adjustments.

The optical interface operates at a 100 Mbps Ethernet rate. It can be one-to-one

mapped over Ethernet or controlled via a PC. Included is a driver that allows the

CNFE2MC2C[/M] to read or write contact information from a PC-based application.

A software utility allows customers to search for this device when installed on the

network. The CNFE2MC2C[/M] supports Windows® Discovery.

Open source com0com TCP/IP protocol is supported for any customer PC applications

to communicate with the units over the Ethernet. The software utility allows customers

to create virtual com ports for each module installed on the same subnet.

These media converters are environmentally hardened to operate in extreme

temperatures. LED indicators are provided to determine equipment operating status.

The CNFE2MC2C[/M] has a normally-open Fiber optic link alarm relay output.

The CNFE2MC2C[/M] small package size allows the unit to be installed in those

locations where space is at a premium, either wall or rack-mounted, or may be DIN-rail

mounted by the addition of ComNet model DINBKT1 adaptor plate.

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 2

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Contents

Hardware description 3

Assign IP Address to a Module 5

Using Module as Remote Contact over Ethernet 12

Install ComNet Software Utilities 13

Install the com2com 13

Install the com2tcp 17

Install ComNet Module Configuration software 18

Using the Module through a Virtual COM port (VCP) 20

Manual VCP Configuration 23

Verify VCP Operation 25

Using TeraTerm Telnet Connection 26

Using Windows UPnP to Discover

Your Contact over Ethernet modules 27

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 3

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Hardware description

The ComNet™ CNFE2MC2C[/M] contact over Ethernet module supports up to 2 bi-directional

contact closures over Cat5/6 cable, or 1 or 2 optical fibers. All configurations are done through

its web server. The CNFE2MC2C[/M] has two contact inputs and two contact outputs, which

communicate through the network. Distances depend on which SFP (Small Form Pluggable)

module is used.

Mechanical Drawing of CNFE2MC2C/M MODULE

Mechanical Drawing of CNFE2MC2C MODULE

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 4

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

The contact connector pin-out is as below:

CNFE2MC2C[/M] Module Input/Output Mapping

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 5

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Assign IP Address to a Module

A unique IP address has to be assigned to each contact over Ethernet application. You

can connect one at a time to change the default IP address. The default IP address of the

CNFE2MC2C[/M] is: 192.168.10.1.

Connect the module on to your local Ethernet network that your PC is connected to, as Figure 1

below, and power on the unit.

Figure 1 – Local Ethernet Application Diagram

Following the steps below to set up your PC IP address to the same subnet as the modules:

»Disable the machine’s wireless network connection and any other internet connections

that could interfere with the network being created. Select the Internet Protocol (TCP/

IP) connection within the Local Area Connection Properties from start, Control Panel, and

Network Connections. Then click Properties.

Figure 2 – Local Area Connection Properties Dialog Box

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 6

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

»Next, manually set your PC IP address to 192.168.10.100 and your subnet mask to

255.255.255.0, as shown below.

Figure 3 – Internet Protocol (TCP/IP) Properties Dialog Box

»Click OK to finish the setting.

»Open the browser on your PC, and type in 192.168.10.100 to reach the Media Converter Log In

page (Figure 4).

»The default User Name and Password are both admin. Log in to the Media Converter Home

Page (Figure 5) as shown.

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 7

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Figure 4 – CNFE2MC2C[/M] Log in Page

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 8

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Figure 5 – CNFE2MC2C[/M] Home Page

»Click on the Configuration link on the left of the screen. Change the IP address to an IP

address with subnet appropriate for your network. In the following examples an IP address in

subnet 192.168.10.xxx will be used. Configure the IP address to 192.168.10.2 as shown in the

Module Configuration Page.

»Click OK.

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 9

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

Figure 6 – CNFE2MC2C[/M] Configuration Page

»Log in to the module again using the new IP address 192.168.10.2. If an IP address in a

different subnet was used, be sure to change the PC’s network address to an IP address in the

appropriate subnet.

INS_CNFE2MC2C[/M]_REV–

01/18/12 PAGE 10

INSTALLATION AND OPERATION MANUAL CNFE2MC2C[/M]

Tech Support: 1.888.678.9427

»Change Contact input/output settings as shown in Table 1.

Contact Input Contact Output

Local Network Port Number 23 26

Remote Network Port Number 26

Network Mode Server Client

Network Protocol TCP/IP TCP/IP

Server IP 192.168.10.1

TCP/IP Timeout 0 0

Table 1 – Contact Input/Output Settings

»Save the configuration changes. Connect this unit and another unit with default configurations

to your local network as shown in Figure 10. The contacts will be linked between the units

through the network.

Figure 7 – CNFE2MC2C[/M] Settings Page in Client Mode

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Comnet Convertitore multimediale

Comnet

Comnet CNGE2MCPOEM Manuale utente

Comnet

Comnet CWFE1005POEMHO-M Manuale utente

Comnet

Comnet RLMCSFP Series Manuale utente

Comnet

Comnet CNFE2MC Manuale utente

Comnet

Comnet CNMC2+1SFP Manuale utente

Comnet

Comnet FVT1D11 Manuale utente

Comnet

Comnet CWFE2SC2 Manuale utente

Comnet

Comnet CWFE2SC2 Manuale utente

Comnet

Comnet CNFE100-A Manuale utente

Comnet

Comnet CNGEMC4+2/M Manuale utente

Comnet

Comnet CWGE2SCS2 Guida rapida

Comnet

Comnet CWFE2SCM2 Manuale utente

Comnet

Comnet CWFE1003POEM/M Manuale utente

Comnet

Comnet CNFE2MCPOE Manuale utente

Comnet

Comnet FVT40D2I1C4E Manuale utente

Comnet

Comnet ValueLine FVT812 Manuale utente

Comnet

Comnet CNFE2MC Manuale utente

Comnet

Comnet CNFE1003POEM/M Manuale utente

Comnet

Comnet CWGE2SFP Manuale utente

Comnet

Comnet CNMC SFP Series Manuale utente

Comnet

Comnet CNFE2MCPOE Manuale del proprietario

Comnet

Comnet FVT10D2I1C4E Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente