Compaq ML330 - ProLiant - G3 Manuale utente

Internal Two-Bay

Hot-Plug SCSI Drive Cage

Installation Card for

ProLiant ML330 Generation 2 Servers

ProLiant ML350 Servers

with 1-GHz Processors

ProLiant ML350 Generation 2 Servers

ProLiant ML370 Generation 2 Servers

OPEN CARD COMPLETELY BEFORE BEGINNING INSTALLATION

PROCEDURES

Compaq, the Compaq logo, and ProLiant

Reg. U.S. Pat. & Tm. Off. All other product names mentioned herein

may be trademarks of their respective companies.

Compaq shall not be liable for technical or editorial errors or

omissions contained herein. The information in this document is

provided “as is” without warranty of any kind and is subject to

change without notice. The warranties for Compaq products are set

forth in the express limited warranty statements accompanying such

products. Nothing herein should be construed as constituting an

additional warranty.

INTERNAL TWO-BAY HOT-PLUG SCSI DRIVE CAGE

Second Edition (September 2001)

Part Number 246499-002

Bar Code Here

Overview

Use this installation card to install a two-bay hot-plug SCSI drive

cage in Compaq ProLiant™ ML330 Generation 2 servers,

ProLiant ML350 servers, and ProLiant ML370 Generation 2 servers.

With this option installed into the server’s removable media bay, you

can add two additional hot-plug SCSI hard drives or one hot-plug

SCSI hard drive and one hot-plug SCSI tape drive.

IMPORTANT: If an internal SCSI connector is not available for managing your

drivecage,installa SCSIcontrolleror arraycontroller.Ensureyouhavetheneeded

controller beforeyou install the drive cage.

For additional information about installing hardware options, refer to

the setup and installation guide on the documentation CD that ships

with your server.

Kit Contents

■ Installation screws and cable



G

Torx 6-32 ×0.25 guide screws (4)

G

Torx 6-32 shoulder screws (4)

G

Ultra3 or higher point-to-point SCSI cable

G

Bezel 2 for ProLiant ML330 installations only

■ Two-bay hot-plug SCSI drive cage



■ 0.6-inch blank



■ Drive blank (slot 1)



■ Drive blank (slot 0)



Warnings and Cautions

WARNING: Because a server is veryheavy, reduce the risk of personal

injuryor damage to the equipment by performing the following:

■ Observe local occupational safetyand health requirementsand

guidelines for material handling.

■ Use more than one person to lift and maneuver the server.

■ Ensure the server castersare locked in place on tower models.

WARNING: Reduce the risk of personal injury fromhot surfaces by

allowing the internal systemcomponents to cool before touching them.

WARNING: Reduce the risk of personal injury bydisconnecting all AC

power from your system before installing non-hot-plug hardware options

into your server.

WARNING: SettingyourPowerOn/Standbybuttontothestandbyposition

removes power from most areas of the server; this transition from on to

standby mode may take 30seconds. Portionsof the power supplyand

some internal circuitry remain active until the AC power cord is removed.

CAUTION: To maintain proper airflow and cooling in the server:

■ Ensure the server’sremovable media bay blanks remain in place

until you are readyto install the two-baydrive cage.

■ Ensurethedriveblanksand 0.6-inchblankremainin placeuntilyou

are readyto install the SCSI devices.

Preparing the Server for Installation

Refer to the setup and installation guide on the documentation CD

that ships with your server to prepare your system for the two-bay

drive cage installation. Before installing the drive cage:

1. Back up all storage devices powered by the system.

2. Shut down the operating system as outlined in the operating

system instructions.

3. Press the Power On/Standby button. The power LED turns to

amber when the server has been successfully placed into standby

mode.

4. Unplug all AC power cords from the server.

5. Disconnect all remaining external cables from the server.

6. Prepare the server for access panel removal:

G

For rack-mounted servers, unscrew the thumbscrews holding

the server in the rack and extend the server.

G

For tower model servers, unlock and remove the front bezel

door.

7. Remove the access panel.

8. Identify the internal SCSI connector for managing your two-bay

drive cage by performing one of the following:

G

Locate an available SCSI connector.

G

Install a SCSI controller or array controller in a PCI

expansion slot.

9. Determine the location of the removable media bay.

10. Remove the removable media bay blanks.

Locating the Two-Bay Drive Cage Mounting

Holes

Screws attach to each side of the drive cage to guide it into position

in the server. Use the following figure and table to determine the

screw type and mounting holes that support your server model.

Table 1

Two-Bay Drive Cage Screw Hole Assignments

Chassis Mounting Holes Screw Type Server Models

Torx 6-32 ×0.25

guide screw ProLiant ML350

servers with 1-GHz

processors and

ProLiant ML350

Generation 2 servers



Torx 6-32 shoulder

screw ProLiant ML370

Generation 2 servers



Torx 6-32 ×0.25

guide screw ProLiant ML330

Generation 2 servers

Installing the Two-Bay Drive Cage into

ProLiant ML330 Servers

1. Using a Tork T-15 screwdriver, replace the bezel that ships

attached to the drive cage with Bezel 2 from the kit.

IMPORTANT: Be sure that the unit identification numbers(0 and1) appearon the

right side of the drive cage front panel.

2. Remove two media bay blanks and move the CD-ROM drive to

prepare a space for the the drive cage.

3. Remove the guide screws and rails from a removable media bay

blank.

IMPORTANT: Be sure to install the railson the drive cage using the screws that

ship with this option kit, rather than the screwsremoved from the rails.

IMPORTANT: Be sure to install the right-hand rail on the left side of the drive

cage,and the left-hand rail on the right side of the drive cage.

4. Using a Torx T-15 tool, position the rails and two guide screws in

the lower mounting holes (see Table 1) on each side of the drive

cage.

5. Insert the SCSI cable that ships with this option kit into the rear

of the removable media bay area and pull it forward for

connection to the SCSI connector on the back of the drive cage.

6. Locate the power cable inside the server and connect it to the

power connector on the back of the drive cage.

IMPORTANT: Alwaysuse the SCSI cable that ships with this option kit. Other

available SCSI cablesmay not support Ultra3SCSI.

7. Slide the drive cage into the removable media bay area until it

locks into place.

8. Connect the other end of the SCSI cable to the desired internal

SCSI connector.

Installing the Two-Bay Drive Cage into

ProLiant ML350 Servers with 1-GHz

Processors and ProLiant ML350 Generation 2

Servers

1. Remove the guide screws from a removable media bay blank as

instructed in the setup and installation guide on the

documentation CD that ships with your server, or use the guide

screws from the bag included with this option kit.

2. Using a Torx T-15 tool, position two guide screws in the upper

mounting holes (see Table 1) on each side of the drive cage.

3. Insert the SCSI cable that ships with this option kit into the rear

of the removable media bay area and pull it forward for

connection to the SCSI connector on the back of the drive cage.

4. Locate the power cable inside the server and connect it to the

power connector on the back of the drive cage.

IMPORTANT: Alwaysuse the SCSI cable that ships with this option kit. Other

available SCSI cablesmay not support Ultra3SCSI.

5. Slide the drive cage into the removable media bay area until it

locks into place.

6. Connect the other end of the SCSI cable to the desired internal

SCSI connector.

Installing the Two-Bay Drive Cage into

ProLiant ML370 Generation 2 Servers

1. Remove the shoulder screws from a removable media bay blank

as instructed in the setup and installation guide on the

documentation CD that ships with your server, or use the

shoulder screws from the bag included with this option kit.

2. Using the Torx T-15 tool clipped to the rear of your server,

position two shoulder screws in the upper mounting holes

(see Table 1) on each side of the drive cage.

3. Insert the SCSI cable that ships with this option kit into the rear

of the removable media bay area and pull it forward for

connection to the SCSI connector on the back of the drive cage.

4. Locate the power cable inside the server and connect it to the

power connector on the rear of the drive cage.

IMPORTANT: Alwaysuse the SCSI cable that ships with this option kit. Other

available SCSI cablesmay not support Ultra3SCSI.

5. Slide the drive cage into the removable media bay area until it

locks into place.

6. Connect the other end of the SCSI cable to the desired internal

SCSI connector.

Preparing the Server for Operation

Refer to the setup and installation guide on the documentation CD

that ships with your server for more detailed instructions. To prepare

your server for operation:

1. Replace the access panel.

2. Secure the server:

G

For rack-mounted servers, slide the server into the rack and

secure in place and tighten the thumbscrews.

G

For tower model servers, reattach the front bezel door.

3. Reconnect the AC power cords and all external cabling.

4. Power up the server.

Installing Hot-Plug SCSI Devices

1. Remove blanks from the drive cage bays to facilitate installation

of the SCSI device.

IMPORTANT: Remove the 0.6-inch blank onlywhen installing a 1.6-inch device.

Otherwise, leave the 0.6-inch blank inplace. Leave blanksin all unpopulated bays

to maintain properairflow and cooling.

2. Install and configure the hot-plug SCSI hard drive and/or hot-

plug tape drive according to the instructions that ship with each

device.

The installation is complete.

Altri manuali per ML330 - ProLiant - G3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Compaq Magazzinaggio

Compaq

Compaq 230050-001 - StorageWorks NAS B3000 Model N900... Manuale utente

Compaq

Compaq SW TL881 DLT Mini-Lib/1 Manuale utente

Compaq

Compaq SDLT 110 Istruzioni utente

Compaq

Compaq 179740-001 - ProLiant - 3000 Guida di riferimento rapido

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manuale di istruzioni

Compaq

Compaq DLT Manuale utente

Compaq

Compaq QUICKSPECS 294162-B21 Istruzioni utente

Compaq

Compaq Storage Works ESL9198 Series Manuale di installazione e funzionamento

Compaq

Compaq MSL5026 Manuale utente

Compaq

Compaq StorageWorks 4000 - RAID Array Guida di riferimento rapido

Compaq

Compaq TL891 - DLT Tape Library Manuale utente

Compaq

Compaq 230039-001 - StorageWorks NAS Executor E7000 Model 904... Manuale utente

Compaq

Compaq BL10e - HP ProLiant - 512 MB RAM Manuale utente

Compaq

Compaq StorageWorks 4000 - RAID Array Guida di riferimento rapido

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manuale di istruzioni

Compaq

Compaq SW TL881 DLT Mini-Lib/1 Manuale utente

Compaq

Compaq 230050-001 - StorageWorks NAS B3000 Model N900... Manuale utente

Compaq

Compaq Hot-Pluggable Wide Ultra2 Manuale utente

Compaq

Compaq SDLT 110 Manuale utente

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manuale di istruzioni

Compaq

Compaq StorageWorks 4100 - RAID Array Manuale utente

Compaq

Compaq 219700-001 - ProLiant - 1500 Manuale utente

Compaq

Compaq RA8000 Manuale utente

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manuale di istruzioni

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente