Comtech EF Data CiM Series Istruzioni operative e di manutenzione

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, (480) 333-2200, FAX: (480) 333-2161.

CiM

Quick-Start Guide

For IP Enabled Satellite Modems

Part Number CD/CIMQSTART.IOM

Rev. 1

Sept. 9, 2002

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

CUSTOMER SUPPORT

Contact Comtech EF Data Customer Support for:

 Product support or training

 Information on upgrading or returning a product

A Customer Support representative may be reached at:

Comtech EF Data

Attention: Customer Support Department

2114 West 7th Street

Tempe, Arizona 85281 USA

(480) 333-2200 (Main Comtech EF Data Number)

(480) 333-4357 (Customer Support Desk)

(480) 333-2161 FAX

or, E-Mail can be sent to the Customer Support Department at:

[email protected]

1. To return a Comtech EF Data product (in-warranty and out-of-warranty) for

repair or replacement:

2. Request a Return Material Authorization (RMA) number from the Comtech

EF Data Customer Support Department.

3. Be prepared to supply the Customer Support representative with the model

number, serial number, and a description of the problem.

4. To ensure that the product is not damaged during shipping, pack the product

in its original shipping carton/packaging.

5. Ship the product back to Comtech EF Data. (Shipping charges should be

prepaid.)

iii

Table of Contents

CHAPTER 1. GETTING STARTED ............................................................................. 1

1.1 Introduction............................................................................................................................. 1

1.2 Typpical Point-to-Point System Configuration.................................................................... 1

1.3 Equipment List........................................................................................................................ 2

1.4 Equipment Setup..................................................................................................................... 2

1.5 PC Configuration.................................................................................................................... 2

1.6 Transmit and Receive IF Configuration............................................................................... 3

1.7 Basic IP Configuration ........................................................................................................... 3

1.7.1 Main Menu......................................................................................................................... 4

1.7.2 Restoring factory Default Configuration ........................................................................... 4

1.7.3 CiM 1 Configuration.......................................................................................................... 5

1.7.4 CiM 2 Configuration.......................................................................................................... 6

1.7.5 Verification ........................................................................................................................ 7

1.8 Using Encryption .................................................................................................................... 8

1.8.1 CiM 1 Configuration.......................................................................................................... 8

1.8.2 Configuration ..................................................................................................................... 9

1.8.3 Verification ...................................................................................................................... 10

1.9 Other Configuration Items...................................................................................................11

1.9.1 User Names & Passwords................................................................................................ 11

1.9.2 Access Lists ..................................................................................................................... 11

1.9.3 Enabling/Disabling Telnet ............................................................................................... 13

Figures

Figure 1. Typical Point-to-Point System Configuration ................................................................ 1

Figure 2. Main Menu ..................................................................................................................... 4

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

OVERVIEW OF CHANGES TO PREVIOUS EDITION

CD/CIMQSTART.IOM Rev. 1 replaces part number CD/CIMQSTART.IOM Rev. -.

A summary of the changes made for Rev. 1 includes:

Chapter 1 Changed addresses in Figure 1 and through out the procedure.

ABOUT THIS MANUAL

This manual provides installation and operation information for the Comtech EF Data

CiM-IP Enabled Modems. This is a technical document intended for earth station

engineers, technicians, and operators responsible for the operation and maintenance of

the CiM-IP Enabled Modems.

CONVENTIONS AND REFERENCES

CAUTIONS AND WARNINGS

IMPORTANT

Indicates information critical for proper equipment function.

CAUTION

Indicates a hazardous situation that, if not avoided, may result in minor or moderate

injury. CAUTION may also be used to indicate other unsafe practices or risks of

property damage.

WARNING

Indicates a potentially hazardous situation that, if not avoided, could result in

death or serious injury.

METRIC CONVERSION

Metric conversion information is located on the inside back cover of this manual. This

information is provided to assist the operator in cross-referencing English to Metric

conversions.

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

RECOMMENDED STANDARD DESIGNATIONS

Recommended Standard (RS) Designations have been superseded by the new designation

of the Electronic Industries Association (EIA). References to the old designations are

shown only when depicting actual text displayed on the screen of the unit (RS-232, RS-

485, etc.). All other references in the manual will be shown with the EIA designations

(EIA-232, EIA-485, etc.) only.

TRADEMARKS

All product names mentioned in this manual may be trademarks or registered trademarks

of their respective companies and are hereby acknowledged.

REPORTING COMMENTS OR SUGGESTIONS CONCERNING THIS MANUAL

Comments and suggestions regarding the content and design of this manual will be

appreciated. To submit comments, please contact the Comtech EF Data Customer

Support Department.

EMC COMPLIANCE

This is a Class A product. In a domestic environment, it may cause radio interference that

requires the user to take adequate protection measures.

EN55022 COMPLIANCE

This equipment meets the radio disturbance characteristic specifications for information

technology equipment as defined in EN55022.

EN50082-1 COMPLIANCE

This equipment meets the electromagnetic compatibility/generic immunity standard as

defined in EN50082-1.

FEDERAL COMMUNICATIONS COMMISSION (FCC)

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment.

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

This equipment generates, uses, and can radiate radio frequency energy. If not installed

and used in accordance with the instruction manual, it may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference; in which case, users are required to correct the interference at their

own expense.

Note: To ensure compliance, properly shielded cables for DATA I/O shall be used. More

specifically, these cables shall be shielded from end to end, ensuring a continuous shield.

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

vii

SAFETY COMPLIANCE

EN 60950

Applicable testing is routinely performed as a condition of manufacturing on all units to

ensure compliance with safety requirements of EN60950.

This equipment meets the Safety of Information Technology Equipment specification as

defined in EN60950.

LOW VOLTAGE DIRECTIVE (LVD)

The following information is applicable for the European Low Voltage Directive

(EN60950):

<HAR> Type of power cord required for use in the European Community.

CAUTION: Double-pole/Neutral Fusing.

ACHTUNG: Zweipolige bzw. Neutralleiter-Sicherung.

International Symbols:

Symbol Definition Symbol Definition

Alternating Current. Protective Earth.

Fuse. Chassis Ground.

Note: For additional symbols, refer to “Cautions” listed earlier in this preface.

CiM Quick Start Guide Rev. 1

Preface CD/CIMQSTART.IOM

viii

WARRANTY POLICY

This Comtech EF Data product is warranted against defects in material and workmanship

for a period of two years from the date of shipment. During the warranty period, Comtech

EF Data will, at its option, repair or replace products that prove to be defective.

For equipment under warranty, the customer is responsible for freight to Comtech EF

Data and all related custom, taxes, tariffs, insurance, etc. Comtech EF Data is responsible

for the freight charges only for return of the equipment from the factory to the customer.

Comtech EF Data will return the equipment by the same method (i.e., Air, Express,

Surface) as the equipment was sent to Comtech EF Data.

LIMITATIONS OF WARRANTY

The foregoing warranty shall not apply to defects resulting from improper installation or

maintenance, abuse, unauthorized modification, or operation outside of environmental

specifications for the product, or, for damages that occur due to improper repackaging of

equipment for return to Comtech EF Data.

No other warranty is expressed or implied. Comtech EF Data specifically disclaims the

implied warranties of merchantability and fitness for particular purpose.

EXCLUSIVE REMEDIES

The remedies provided herein are the buyer's sole and exclusive remedies. Comtech EF

Data shall not be liable for any direct, indirect, special, incidental, or consequential

damages, whether based on contract, tort, or any other legal theory.

DISCLAIMER

Comtech EF Data has reviewed this manual thoroughly in order that it will be an easy-to-

use guide to your equipment. All statements, technical information, and

recommendations in this manual and in any guides or related documents are believed

reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and

they are not intended to be, nor should they be understood to be, representations or

warranties concerning the products described. Further, Comtech EF Data reserves the

right to make changes in the specifications of the products described in this manual at any

time without notice and without obligation to notify any person of such changes.

If you have any questions regarding the equipment or the information in this manual,

please contact the Comtech EF Data Customer Support Department

Chapter 1. Getting Started

Introduction 1

Sample Configuration 1

Equipment List 1

Equipment Setup 2

PC Configuration 2

Transmit and Receive IF Configuration 3

Basic IP Configuration 3

Using Encryption 8

Using QoS 11

Other Configuration Items 11

1.1 INTRODUCTION

This quick start guide will allow a user to configure a pair of CiM-550 or CiM-300L

(referred to CiM in rest of the document) from beginning (i.e. starting from factory

default settings) and be able to pass traffic within minutes. It is assumed that the user is

familiar with the configuration of the base satellite modem.

1.2 TYPICAL POINT-TO-POINT SYSTEM CONFIGURATION

The steps in this guide will lead to following configuration:

IP Address:

Mask:

GW:

172.16.10.100

255.255.255.0

172.16.10.10

PC 1

Satellite IP Modem (CiM 1)

Ethernet Interface (fei0)

IP Address:

Mask:

172.16.10.10

255.255.255.0

HDLC Interfacce (hdl1)

IP Address:

Mask:

10.1.1.1

255.255.255.0

10/100 BaseT

Etherneet Hub

RF or IF

IP Address:

Mask:

GW:

172.17.10.100

255.255.255.0

172.17.10.10

PC 2

Satellite IP Modem (CiM 2)

10/100 BaseT

Etherneet Hub

Ethernet Interface (fei0)

IP Address:

Mask:

172.17.10.10

255.255.255.0

HDLC Interfacce (hdl1)

IP Address:

Mask:

10.1.1.2

255.255.255.0

Figure 1. Typical Point-to-Point System Configuration

CiM Quick Start Guide Rev. 1

Operation CD/CIMQSTART.IOM

1.3 EQUIPMENT LIST

Following equipment is required:

Item Equipment Quantity Comments

1 CiM-550 Modem 2

2 10/100baseT Ethernet Hub 2 Provided by customer

3 PC with NIC and a terminal

emulation program

2 Provided by customer

4 Console cable (DB-9 to RJ-11) 1 Can be procured from Comtech EF Data

5 Ethernet cables 4 Provided by customer

6 IF cables 2 Provided by customer

(For IF loopback only. Additional

equipment required for RF connectivity.)

7 Traffic Generator such as

SmartBits

1 Provided by customer

1.4 EQUIPMENT SETUP

Step Description

1 Connect each CiM to the PC via the Ethernet Hub.

2 Connect the TX IF on CiM 1 to RX IF of CiM 2 and vice-versa.

3 Connect the DB-9 end of the console cable to the COM1 or COM2 port of the PC and

the RJ-11 end to the console port at the back of CiM 1.

4 Connect CiM 1 and CiM 2 to suitable power supply and turn them ON.

1.5 PC CONFIGURATION

Step Description

1 Set the IP address on PC 1 to 172.16.10.100, mask to 255.255.255.0 and gateway to

172.16.10.10.

2 Set the IP address on PC 2 to 172.17.10.100, mask to 255.255.255.0 and gateway to

172.17.10.10.

Reboot the PCs (if required).

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Comtech EF Data Modem

Comtech EF Data

Comtech EF Data CDM-750 Manuale utente

Comtech EF Data

Comtech EF Data Vipersat CDM-570 Manuale utente

Comtech EF Data

Comtech EF Data CDM-740 Manuale utente

Comtech EF Data

Comtech EF Data CDM-625 Manuale utente

Comtech EF Data

Comtech EF Data CDM-710 Manuale utente

Comtech EF Data

Comtech EF Data CDM-710 Manuale del proprietario

Comtech EF Data

Comtech EF Data CDM-600 Manuale utente

Comtech EF Data

Comtech EF Data SLM-5650B Manuale utente

Comtech EF Data

Comtech EF Data CDM-Qx Manuale utente

Comtech EF Data

Comtech EF Data CIM-300L Manuale

Comtech EF Data

Comtech EF Data SMS-301 Manuale utente

Comtech EF Data

Comtech EF Data SDM-9000 Manuale utente

Comtech EF Data

Comtech EF Data CDM-600L Manuale utente

Comtech EF Data

Comtech EF Data FX series 1005 Manuale di servizio

Comtech EF Data

Comtech EF Data Vipersat SLM-5650A Manuale utente

Comtech EF Data

Comtech EF Data CDM-700 Manuale utente

Comtech EF Data

Comtech EF Data SNM-1001L Manuale utente

Comtech EF Data

Comtech EF Data SDM-300A Manuale utente

Comtech EF Data

Comtech EF Data CDM-710G Manuale utente

Comtech EF Data

Comtech EF Data CDM-425 Manuale utente

Comtech EF Data

Comtech EF Data SLM-7650 Manuale utente

Comtech EF Data

Comtech EF Data SDM-650B Manuale utente

Comtech EF Data

Comtech EF Data CDM-550T Manuale utente

Comtech EF Data

Comtech EF Data cdm-570a Manuale utente

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

Paradyne

Paradyne Hotwire 7976 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente