Comtronics 246559 Manuale utente
246559 - Center Dash Shelf Mount
Ford Crown Victoria Police Interceptor 1995-2012
Installaon Instrucons
ComtronICS CobaltAV |2350 Fortune Drive, Lexington KY 40509
USTF: 1.800.264.6021 |PH: 859.299.9494 |FAX: 859.299.9334
©2015 ComtronICS Cobalt AV. All rights reserved.
With ComtronICS’ new EZ Dash Mount, your tablet is securely
mounted on the vehicle’s dash, adjusts for mulple viewing
posions, and frees up valuable space in your
vehicle’s interior.
By ProClip USA
1. Remove the front panel that the trunk release buon is located on.
2. Start at the right side and work your way le. Unplug the trunk release wires to completely
remove the panel. Set the panel aside.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
3. Remember to also remove the short panel on the leside of the steering wheel. Start with the far
leside of the panel.
4. Once the lower panels have been removed, take out the eight screws that fasten the frame
around the radio and instruments. Remember the two above the speedometer.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
5. Pull out the instrument panel starng under the radio area. Detach the wires behind the radio.
Remember to also lt the steering wheel all the way down to remove the instrument panel.
6. Detach the wires from the light switches on the far le. Once the wires are detached, remove the
switches from the panel by pressing forward on the switch panel.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
7. Once the switch panel is removed from the instrument panel, plug the wires back into the
switches. This will quiet the connuous beeping from the light switch sensor.
8. Completely remove the instrument frame from the vehicle.
9. Cover the opening in the carpet under the center console area. This will reduce the chances of
losing nuts and bolts that might drop into the area.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
10.The connecng block will aach to the slots on the steel dash frame behind this opening. (See
arrows)
11. Push out the plasc clips holding on the wire harness and press the wire harness back or out of
the way of the slots in the steel frame.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
12. Insert the included “T” bolts with a square neck into the back of the right slot on the steel frame
in the opening. (Tip: It will be easier to loosely aach only the right side of the block first. Also, it
might be helpful to tape the “T” bolts in from the back side.)
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
13. When aaching the connecng block, the threaded hole for the connecng screw on the
connecng block should be facing downward. Fasten onto the “T” bolt with the included nut and lock
washer. (Tip: It will be easier to hold the connecng block when the screw is inserted into the
threaded hole.)
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
14. A very helpful tool will be a “universal” aached to a driver or socket wrench. This tool will assist
in fastening the nuts onto the “T” bolts in the connecng block.
15. Align the lehole up with the leslot in the steel dash frame.
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
16. Insert the included “T” bolts with a square neck into the back of the leslot on the steel frame in
the opening. Fasten with the included nut and lock washer. (Tip: Again, it might be helpful to tape the
“T” bolt in from the back side.)
17. Above, the connecng block aached. (Tip: keep the connecng block towards the right in the
slots.)
Ford Crown Victoria
Police Interceptor 1995-2012
Installaon Instrucons
By ProClip USA
Indice
