Concox General GPS Vehicle Tracker Manuale utente
General GPS Vehicle Tracker
User Manual
V1.0
Introducing your Device
Learn about your device’s layout, indications and specifications.
1. Inside the Box
Check your product box for the following items:
Device
Charging cable
Relay
User Manual
2. Overview
LED Indicators
Power indicator (red)
Indication
Quick Flashing (flash 0.3s at interval of 0.3s)
Low battery
Solid red
Charging
Flashing (flash 1s at interval of 3s)
Full charge
Off
Power off or low battery
Slow flashing (flash 0.1s at interval of 3s)
Working normally
GPS indicator (blue)
Indication
Flashing (flash 1s at interval of 3s)
Searching GPS signal
Slow flashing (flash 0.1s at interval of 3s)
Receive GPS signal normally
OFF
No GPS signal
GSM indicator (green)
Indication
Quick Flashing (flash 0.3s at interval of 0.3s)
GSM initializing
Flashing (flash 1s at interval of 3s)
Receive GSM signal normally
Solid green
In communication with phones
OFF
No GSM signal or no SIM card
Slow flashing (flash 0.1s at interval of 3s)
GPRS on line
3. Specifications
Dimension
78.0(L) x 41.0(W) x 13.0(H) mm
Weight
38g
Voltage range
7.5-90V
Backup Battery
270mAh / 3.7V
Operation Temperature
-20℃-70℃
Humidity
20% - 80%
Standby Time
50 hours
GSM Frequencies
850/900/1800/1900 MHz
GPRS
Class 12, TCP/IP
GPS Channel
66
GPS Sensitivity
-165dBm
Acquisition Sensitivity
-148dBm
Position Accuracy
<10m
TTFF （Open Sky）
Cold Start: ＜45s
Hot Start：＜2s
GSM/GPS Antenna
Built-in design
LED Indicator
GSM-green, GPS-blue, Power-red
Data Transmit
TCP, SMS
Geo-fence Alarm
Alarm when get in or get out a specified area
Speeding Alarm
Report when speeds higher than the pre-set value.
Low Power Alarm
Alarm when backup battery is running out
Non-movement
Detection
Movement alarm based on built-in 3D motion
sensor
Mileage Report
Track by time/distance interval
Remote Control
Cut off petrol/electricity
4. Getting Started
4.1 Switch on
Get started by assembling and setting up your device for its first use.
1.Open the SIM card cover.
2.Insert the SIM card.
Note: SIM card should be equipped with GPRS and SMS functions.
3.Turn power on.
4.Close the SIM card cover and connect the device with the external power line
which will be used to charge the terminal and built-in battery.
4.2 Switch off
1.Take the SIM card out and turn power off.
2.Close the SIM card cover and cut external power off.
4.3 Charge the device (Covert installation)
Plug the device connector into a charging cable.
The charging cable with 2A FUSE for short-circuit over current protection.
Note：Improperly connecting the charging cable can cause serious damage to the
device. Any damages by misuse are not covered by the warranty.
4.4 Install the device
You need to choose somewhere that it won't be found, because the whole point of
fitting covert GPS vehicle tracker is the secrecy element.
1. Your device has built-in GSM antenna and GPS antenna. During installation,
please make sure the receiving side face is up ; any high power devices such as
reversing radar, anti-theft device or communication equipment would affect the
signal of the device.
2. All metallic cases of the windshield will attenuate the signal on the tracking
device. It’s simply due to the shielding effects of the metal compound of the case.
3. The device should be fixed into position with cable ties or wide double-side tape.
Installation please refers to below picture.
- Under the dash board below the front windshield;
- In the parcel shelf in the rear;
- In the front bumper (non-material face), make sure the device does not get wet;
- Under the wiper version (non-metal), make sure the device does not get wet;
- Non Covert Installation - fix the device on the dash board below windshield.
Device Wiring
1 The standard voltage is 9V- 90V, the red wire is the positive, the black wire is the
negative.
2. Connect the black wire to ground.
4.5 Device wiring diagram
NOTE: Please pay attention to the diagram description, battery is 9-90V and relay
remains 12V / 24V.
4.6 Power/ACC/Tele-cutoff(petrol/electricity)
control line (4 pin)
1. Your device comes with a power cord and is designed to use only
manufacturer-specified original device. The red line is positive while the
black one is negative (the side should not be connected with ground
wire).
2. The ACC line (orange) connects to ACC switch of the vehicle. Please be
sure to connect the ACC line; otherwise the device will enter ignition
detection status when disconnect the ACC line. If you don’t need to
anti-theft temporarily, just connect the ACC line to the positive side in
parallel.
3. Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin
86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of
the relay socket).
5. Quick Operation Instructions
To properly use the device, common parameters should be set before initial use.
This can be done by using the parameter editor or by sending SMS commands to
the device. (“,"should be English comma and no space before and after the
comma)
5.1 Add SOS number
SMS command to the device to add the SOS number.
SOS,A,No.1,No.2,No.3#
“A” means to add new numbers, for example:
SOS,A,18165542975,18165542976,18165542977#
It will reply
“OK!”
SOS1: 18165542975 SOS2: 18165542976 SOS3: 18165542977”
Indice
