Concox QBIT M Manuale utente
The product specifications and information in this document are
for reference only and no prior notice will be given if any change
is made. Unless otherwise stated, the content of this document
is not a guarantee in any form.
QBIT M
User Manual V1.0
Disclaimer ©All Rights Reserved
1.Introduction
1.1 Packing List
Qbit M Ejector PinBack ClipLanyard
1.2 Buttons and Interfaces
Power button
SIM card slot
LED indication
Buzzer
SOS button
Lanyard hole
Charging port
1.3 Specifications
1.4 LED Indication
45mm x 41mm x 15mmDimensions
31.8gWeight
IP66Ingress Rating
Cellular Cat-M1: B1, B2, B3, B4, B5, B8, B12, B13,
B14, B18, B19, B20, B25, B26, B28, and B66
Cat-NB1/NB2: B1, B2, B3, B4, B5, B8, B12,
B13, B17, B19, B20, B25, B26, B28, and B66
GNSS GPS L1 C/A support
QZSS L1 C/A support
Battery Built-in 650mAh Li-polymer battery
Connotation Indication
Power on
successfully
The LED lights up white for 1s
and goes out.
Shut down failed
The LED lights up red for 1s and goes
out if the Power button is used for the
shutdown.
Shut down
successfully
The LED lights up white and goes out
if the Power button is used for the
shutdown.
Fixing positions The LED flashes blue every half second.
Network error The LED flashes yellow.
2.Quick Start
2.1 SIM Card Attachment
Align the ejector pin to the hole on the SIM card tray
and pry out part of the tray.
1
Pull out the SIM card tray with your hand.
2
Place the SIM card in the tray with its chip side facing upward,
keep the pry hole upward, and align the tray with the slot.
3
● If the LED lights up red just for 1 second when turning the
device on, it needs charging.
● Use a Type-C cable for the charging (A charger of 5V/1A or
above is recommended, such as the USB port on a computer
or a phone charger). During charging, the LED flashes red.
● The LED turns solid white after the charging is complete.
2.2 Charging
2.3 Device Binding
Use the designated app to scan the IMEI QR code to add
the device to your account. The QR code is printed on the
back cover of the device or the sticker inside the packing
box. If the QR code cannot scan, you can input the 15 digits
under the QR code to bind it.
Gently push the tray into the slot.
Note: The chip side of the SIM card and the opening of
the tray must be facing upward (the side with the panic
button is the up side).
4
If the device is in sleep mode, press the panic button for 4
times in 5 seconds to wake the device up. Upon wakeup,
the device LED will turn blue for 1 second and then work
as preset.
Note: If the device has been configured with a
wakeup prompt tone, the buzzer will beep.
2.4 Powering Device On
If the device is in shutdown state, press and hold the Power
button for 3 seconds, the LED will turn white and the buzzer
will beep twice to indicate that the device has been
successfully powered on.
After that, the device LED flashes blue to indicate it is
working correctly (refer to LED Indication for details).
If the device is in power-on state, press and hold the Power
button for 3 seconds, the LED will turn white and the buzzer
will beep once to indicate that the device has been
successfully shut down.
Note: If an error prompt appears during shutdown, please
check if the device has been configured with a shutdown
restriction.
2.5 Shutting Device Down
2.6 Waking Device Up
3. Setup
3.1 Working Mode
The device can work in 3 modes - regular GPS, intelligent,
and tracking, allowing you to switch based on specific needs.
Regular GPS Mode
In this mode, the device will report location information at a
preset interval. This mode uses the least power and is suitable
for cargo tracking scenarios.
Intelligent Mode
In this mode, the device will adjust its reporting frequency
according to the WiFi geofence setting, operation duration,
and motion status. The device can save power to the largest
extent using such a mechanism.
WiFi Geofencing
Three WiFi geofences are allowed to be set as safe zones. The
device will not report location information by default when inside
any safety zone; and it will report location information according
to the preset operation duration when outside of safety zones.
Operation Duration
The device can be configured with an operation duration to save
power. For example, you can set the out duration (7:00 to 19:00)
as the operation duration of the device and the device will keep
silent in other time periods.
Motion Status
The device can be configured to report location information
only during moving to save power and get as much location
information about the object under tracking. You can also
change the reporting interval based on specific needs.
3.2 Panic Button
If the device is already powered on, you can keep pressing
the panic button to send out SOS alerts. If the operation is
successful, the device will beep 3 times. You will receive an
SOS alert notification on the app.
3.3 Vehicle Finding by Sound
If you are near the device and cannot find it, you can use the
app to activate its buzzer to beep to indicate its location.
3.4 Moving or Parking Notification
Note: This features is only valid when the device works in
intelligent mode.
If you would like to know the motion status of the object under
tracking, you can enable this feature. In this way, you will
receive a notification on the app when the device starts
moving or stops.
Indice
Altri manuali Concox GPS
Concox
Concox GT06F Manuale utente
Concox
Concox Smart OBD Manuale utente
Concox
Concox GPS Vehicle tracker Manuale utente
Concox
Concox GK310 Manuale utente
Concox
Concox GT06N Manuale utente
Concox
Concox GT06N Manuale utente
Concox
Concox Vechile Series Manuale utente
Concox
Concox GPS Electric Cars Positioning Terminal Manuale utente
Concox
Concox GT03A Manuale utente
Concox
Concox smartracker GT350 Manuale utente
