Conlan 460116 Manuale utente

secure open

Conlan ApS • Speditorvej 2A • DK-9000 Aalborg • Tel: +45 72 40 60 03 • Fax: +45 96 32 00 22

www.conlan.eu • [email protected]

Wiegand

Controller

Art. No.: 460116

User manual

Wiegand_usermanual_ENGjun15

Two way - One door controller

Specikations:

• Controller for one door, 2 readers

• Space for 511 user codes/tags + 1 Master code/tag

• 3584o-lineeventswithdateandtimestamp

• Real time clock

• Backup battery for clock, EEProm memory

• Dual-processor

• Fully stand alone or networkable

• Possibillityforstandaloneadd/deletecodes/tagsincludinglostordamagedtagswithoutneedtodeleteall

users or connect to a PC

• PCconnectionviaRS485orRS232

• Network connection or direct connection to RS232 serial port

• Lockingdevicerelay,NO/NCselectablebyJumper/software

• Alarmrelay,NO/NCselectablebyJumper/software

• Door contact input (NC)

• Request to exit button (REX) (NC)

• Inputs for two 26 bit Wiegand readers (In and Out)

• Open collector outputs for reader LED and buzzer

• Stand alone reset using wire

• Tamperswitch(NC)

• 12 Vcc, 500 mA max. power input.

Connections

!!! Caution-readalltheinstructionsinordertoassureaproperworkingofthecontroller

12V; GND Power supply, 12 Vcc, 500 mA max.

T;T Tamperswitch(NC)

GND Ground

x-; x+ RS485 port

LK;LK Lockingdevicerelay

AL; AL Alarm relay

BUZ Open collector output for buzzer

LED Open collector output for LED

COM Common door contact and REX

CM Door contact input

REX Request to exit input (REX)

D0; D1 Data from readers

Power supply

12 V / 500 mA

CM REX

W26CTRL COM CM REX D0 D1 D0 D1LEDBUZ

GND12VTTGNDX-X+LKLKALAL

J1 J2

485 232

Entry Exit

Exit

reader

Entry

reader

Note:

1. Incasethatyouareusingjustonereaderlettheotherinputsunconnected

2. Incasethatyouarenotusingdoorcontactinput,shortcircuitwithawirebetweenCOMandCM.Bydefault

door contact input is NC.

Jumper conguration:

J1 - Alarm relay NO or NC J2-LockingdevicerelayNOorNC J3 - Communication port , RS232 or RS485

Programming:

Bydefault,thefollowingparametersareset:

• Mastercodedened(4711)

• Nousercodes/tagsdened

• Door unlock time = 5 seconds

• Door open time = 30 seconds

• Alarm time = 5 seconds

• Invalidcode/tagstatustime=2seconds

• Re-lockdoor-active

• Re-lockonopening-active

• Door contact type - NC

• REX type NC

Parameters description:

• Door unlock timeisthemaximumactivationtimeforthelockingdevicerelayincaseofavalidcode/tagor

REXactivation.Denedinsecondsfrom1to255.

• Door open timeisthemaximumallowedtimeforthedoortobeleftopen.Thistimestartfromthemoment

ofunlockingthedoor,that’swhythemandatoryistobehigherthenthedoorunlocktime.Ifattheendof

thedoorunlocktimethedoorisstillopen,and“Doorstillopen”eventisgeneratedandloggedandalarm

relayisactivated.Ifyouwanttoletthedoortobeopenedforinnitetime,youshouldsetthistimeatdoor

opentimeto255.Denedinsecondsfrom1to255.

• Alarm Timeisthetimeforalarmrelayactivation.Itstartsfromthemomentofalarmgenerationandend

ofalarmcondition.Ifthedoorisforcedopenwhenalarmrelaywillbestillactiveforalarmtimeafterclosing

thedoor.Sameifthedoorisleftopen.

• Invalid code/card status timeisthetimeforthereaderstoshowtheinvalidstatusofacode/tagusing

LED’sandbuzzer

• Re-lock door-ifactivethedoorisre-lockedwhenitisclosedoropened,dependingofthefollowingsetting

• Relock on opening-isvalidonlyiftheprevioussettingisactive.Ifactivated,thedoorisre-lockedwhenthe

doorisopened,otherwisewhenitisclosing,withoutwaitingfordoorunlocktimetoexpire.

Codes/tags programming:

Forcodes/tagsprogrammingaMastercode/tagisneeded.Thiscanbekeyed/enrolledeitherbystandalonere-

setorbyaPC.Controllermemoryistableconstructed,from0upto511,where0isMasterposition.Werecom-

mendtokeepatableinthefollowingformattobeabletomadeacompletecode/tagprogramming.

Position Code/tag number User name

0 xx:xxxxx Mastercode/tag(4711-default)

1 xx:xxxxx User name 1

2 xx:xxxxx User name 2

... ... ...

511 xx:xxxxx User name 511

Withsystempowered,keyin/presentMastercode/tag.Thesystemgoesintostandaloneprogramming.Pro-

grammingphasesareindicatedbyLEDclippingandbuzzersounds,followedbyapprox.1secondpause.Each

keying/presentationofMastercode/tagputsthesysteminthenextprogrammingphase.

1. Oneshortactivation-keyin/enrollcode/tagintherstfreeposition

2. Twoshortactivations-deleteanexistingcode/tag

3. 3Threeshortactivations-deletealostordamagedtag

!!! ATTENTION - It is very important to know each code/tag position.

Program code/tag in the rst free position.

Withsystemon“Programcode/tagintherstfreeposition”keyin/presentthecode/tagyouwanttokeyin/en-

roll.Thiswillbestoredintherstfreepositioninthetable(writedowntheposition).Ifsomeerroroccurswhile

keying/enrolling,thesystemwillsignalwith“invalidcode/tag”,meaningthatthecode/tagisalreadystoredorthe

memory is full.

Afterprogrammingacode/tag,othercodes/tagscanbeprogrammeddirectly.

Delete an existing code/card.

Withthesystemon“Deleteanexistingcode/tag”keyin/presentthecode/tagyouwanttodelete.Thatcode/tag

willbedeletedfromthememoryandthatpositionbecomesfree.Writedownthatpositionasfreepsition.Ifde-

letioncannotbemadean“invalidcode/tag”signalwillbeshownonthereaders,meaningthatthecode/tagdid

notexistinthedatabase.Afterdeletingacode/tag,otherscanbekeyed/presentedtobedeleteddirectly.

Delete a lost/damaged tag.

Withthisoptionyoucandeleteatagwithouthavingthattag.Itisveryusefulincaseoflost/stolen/damaged

tags.Itispossibletodeleteatagwithoutdeletingallcodes/tagsandwithoutusingaPC-fullystandalone.In

thisphaseitisveryimportanttoknowtheuserpositionsinthedatabase.

Withthesystemon”Deletealost/damagedtag”presentthetaginthepositionlowerthanthecardwewnatto

delete.Forinstance,ifwewanttodeletetaginposition37wewillpresentthetaginposition36.Ifwedonthave

ataginposition36(36isfree)wewillpresentthetaginposition35andsoon.Inohterwords,thisphasecanbe

“Deletersttagenrolledafter(asposition)presentedtag”.

Again,itisveryimportanttonoteallpositionsoftagsenrolledordeleted.

Stand alone reset and Master code/tag programming.

TheMastercode/tagcanbeprogrammedinthefollowingsteps:

1. Powero

2. DisconnecttheCMinput

3. ShortcircuitawirebetweenLEDoutputandCMinput

4. Power on

5. Waitapprox.3secondsofLEDashing,thesystemgoesinto“Programcode/tag”phase,asshownbyLED/

buzzer

6. Keyin/presentthecode/tagthatyouwanttobecomeMastercode/tag

7. Atexitofprogramminguserphasepowerothesystem

8. RemovethewirebetweenCMandLED

9. ReconnecttheCMwirefromthemagneticcontact

10. Power on

Forsecurityreasons,alluserswillbedeletedbeforekeying/enrollingMastercode/tag.Thesystemgoesin“Pro-

gramcode/tag”andsinceallusersaredeleted,therstcode/tagprogrammedinposition0becomesMaster

code/tag.

ThankyouforchoosingConlan’sproducts.

Forfurtherassistance,pleasecontact

Oursupportservice.

Indice

Altri manuali Conlan Controllori di accesso IP

Conlan

Conlan CM1200 Series Manuale utente

Conlan

Conlan Wiegand CT 1200 Family Manuale utente

Conlan

Conlan 3001 Manuale utente

Manuali Controllori di accesso IP popolari di altre marche

ZKTeco

ZKTeco SpeedFace-V5L Manuale utente

Jantar

Jantar REX A-1-9 Manuale utente

2N Access Unit Foglio di istruzioni

Kedacom

Kedacom KSCA120 Series Manuale utente

H3C

H3C WX2880X Manuale utente

G4S

G4S S870-EX Guida

PRASTEL

PRASTEL M2000PE Manuale utente

Allegion

Allegion interflex IF-281 Cylinder Manuale utente

TECOM

TECOM TS1067E Manuale utente

Fermax

Fermax Memokey 100C Guida utente

Fermax

Fermax CITYLINE MEMOKEY Manuale di istruzioni

Software House

Software House iSTAR Pro 2U RM Manuale di istruzioni

AKCP

AKCP SP+ Manuale utente

Bpt

Bpt HNA/102 Manuale utente

Civintec

Civintec CV9601T-T-1F Manuale utente

BioMax

BioMax N-X90W Manuale utente

ZKTeco

ZKTeco OP-200 Manuale utente

FingerTec

FingerTec s-Kadex Manuale utente