Connective Touch SmartPro Manuale utente
SmartPro user manual
ConnectiveTouch.com
Connective Touch
FINGERPRINT READERS
ACCESS CONTROL
SYSTEM
USER GUIDELINES
AG|0510|DS|04|16
SMARTPRO USER MANUAL
1
Contents
GETTING STARTED................................................................ 2
INTRODUCTION ....................................................................2
Glossary of terms / abbreviations ...................................................3
IMPORTANT SAFEGUARDS .......................................................5
INSTALLATION LOCATION........................................................5
USE OF SENSOR ....................................................................5
ENROLMENT PROCESS........................................................... 6
TIPS FOR BEST FINGERPRINT ENROLMENT...................................6
Net2 Setup Considerations...........................................................7
New User Enrolment .................................................................8
New Fingerprint Enrolment (User Token Details) ............................... 13
Deleting FingerPrint templates (User Token Details) ........................... 17
AG|0510|DS|04|16
SMARTPRO USER MANUAL
2
GETTING STARTED
INTRODUCTION
The Connective Touch SmartPro is a PC based Security system for
controlling access through multiple doors using fingerprint biometrics and
integrates with the Paxton facilities management system Net2.
This User Guide details the key functionalities for:
- Fingerprint Enrolment Software for Users on ‘Net2 Access Control’
- The management of Users within ‘Net2 Access Control’
- The management of access to SmartPro Biometric Access Control units
AG|0510|DS|04|16
SMARTPRO USER MANUAL
3
Glossary of terms / abbreviations
CT Connective Touch
FP FingerPrint
FP Admin ‘FingerPrint Admin’ (installed as FP Enrolment
Software) is the CT software used to enrol
fingerprint templates and to control FP Enrolment
and FP Verification Units.
FP Enrolment Unit FP unit always situated by the Administrator PC.
This unit is used to register the fingerprint of a new
user.
FPR FingerPrint Reader –A unit which can be
configured as either a FP Enrolment and/or FP
Verification Unit
FPRegister Installed CT software, the FPRegister application
enables the and administration of fingerprints
within the Net2 system
FPTs FingerPrint Templates –The digital record of a
fingerprint
FP Verification Unit FP unit always situated where access is required i.e.
a door
Net2 Net2/Net2+ is a User/Facilities Management
Software from Paxton used in conjunction with the
Paxton ACU (Access Control Unit).
Net2 Pro /Plus/Lite / Client
Install versions of Net2 Access Control
Net2 Server Paxton supplied administration software
Paxton Net2 v5.03 Supplied administration software
AG|0510|DS|04|16
SMARTPRO USER MANUAL
4
Network Subnet Any building or installation other than the Main
Building or installation.
Subnet As Network Subnet –site name
Token Within Net2 the FingerPrint Templates are referred
to as Tokens
Zone ID Within ‘Fingerprint Admin’ (installed as
FPRegister) the terms Zone and Zone ID are used
to determine a number of doors or access
points registered within a group
AG|0510|DS|04|16
SMARTPRO USER MANUAL
5
IMPORTANT SAFEGUARDS
INSTALLATION LOCATION
Do not install terminal in areas which are exposed to direct and heavy rain,
as the fingerprint readers are not designed to work in those areas.
Fingerprint readers will work with minimum water but recommend they are
wiped off.
USE OF SENSOR
Do not abuse the fingerprint sensor by
scratching the surface, contacting the
sensor’s surface with heat, pressing
excessively hard during placement of
fingerprint for verification, or use
abrasive cleaning products or
implements. Clean the sensor
occasionally with dry or anti-bacterial
wipes to maintain the performance of
the sensor.
Figure 1. SmartPro FP Verification Unit
AG|0510|DS|04|16
SMARTPRO USER MANUAL
6
ENROLMENT PROCESS
The Enrolment Unit is provided to enrol approved personnel into the
SmartPro system. The level permissions of each user are saved in the Main
Administrator PC.
TIPS FOR BEST FINGERPRINT ENROLMENT
WHAT YOU SHOULD DO
Place finger flat on the fingerprint sensor. Make sure
the finger’s midpoint is placed at the centre of the
fingerprint sensor.
WHAT YOU SHOULD NOT DO
3. Plan/Side views
2. Plan/Side views
AG|0510|DS|04|16
SMARTPRO USER MANUAL
7
Net2 Setup Considerations
With regard to all Users consideration should be given to working
parameters as follows:
‘Door groups’ –this is deciding if doors need to be grouped e.g. all
doors in one building
‘Access levels’ –types of access levels required as:
‘No access’
‘All hours, all doors’
‘Working hours’
‘Timezones’ –period to allow entry as:
‘No access
‘All hours, all doors’
‘Working hours’
‘Net2 operators’ –who has permission to access ‘Net2 Access
Control’ and the functionality they require as:
‘New operator’
‘OEM Client’
‘System engineer’
These are all covered in the ‘SmartPro Software Installation Guide’
AG|0510|DS|04|16
SMARTPRO USER MANUAL
8
New User Enrolment
With reference to the diagram below, the first stage in enrolling a new
User is to create the User in ‘Net2 Access Control’:
Log into ‘Net2 Access Control’ using the User name and Password
provided.
A screen similar to the one below will appear after a successful log in.
Figure 4. Net2 Software
Figure 5. Net2 Software
AG|0510|DS|04|16
SMARTPRO USER MANUAL
9
Click on the ‘Users’ tab in the left hand pane and all the Users within
the system will appear.
Figure 6. Net2 Software - Users
4. Click on ‘New user’ in the upper toolbar
5. the ‘Add user’ screen shown
below will appear. The
minimum details that need to
be entered are:
First name
Surname
Token type
Access level
Figure 7. Net2 - Add User
Indice
