Contec CNT24-4D(PCI) Manuale utente

CNT24-4D(PCI)

24Bit Differencial Up/Down Counter Board

for PCI

User’s Guide

CNT24-4D(PCI) i

No part of this document may be copied or reproduced in any form

by any means without prior written consent of CONTEC Co., LTD.

CONTEC Co., LTD. makes no commitment to update or keep

current the information contained in this document.

The information in this document is subject to change without

notice.

All relevant issues have been considered in the preparation of this

document. Should you notice an omission or any questionable

item in this document, please feel free to notify

CONTEC Co., LTD.

Regardless of the foregoing statement, CONTEC assumes no

responsibility for any errors that may appear in this document nor

for results obtained by the user as a result of using this product.

Trademarks

MS, Microsoft, MS-DOS and Windows are trademarks of Microsoft

Corporation. Other brand and product names are trademarks of

their respective holder.

CNT24-4D(PCI)ii

Product Configuration

-CNT24-4D(PCI) Board…1

-CNT24-4D(PCI) SETUP DISK (3.5inch/1.44MB) …1

-User’s Guide (this booklet)…1

Unpacking:

This board is specially packed in an anti-static bag to prevent

damage in shipping.

Check the contents to make sure that you have everything listed

above. If you do not have all the items, contact your distributor

or CONTEC group office where you purchased.

Note! Do not remove the board from its protective packaging until the

computer case is open and ready for installation. Electrical static

can cause damage to electrical components.

CNT24-4D(PCI) iii

Table of Contents

Trademarks ........................................................................i

Product Configuration ..................................................... ii

1. Introduction .............................................................1

Features.........................................................................1

Limited Three-Year Warranty......................................2

How to Obtain Service..................................................2

Liability.........................................................................2

Handling Precautions...................................................3

About the Manual.........................................................4

2. Component Locations and Setting..............................5

Component Locations........................................................5

Setting the Board ID.........................................................6

Setting Procedure .........................................................6

Setting One-shot Pulse Output Signals...........................7

Setting Terminators..........................................................8

3. Board Setup ............................................................. 9

Use CONTEC Windows Software Products.....................9

When Not Using CONTEC Software for Windows .......10

For Windows 98 Systems............................................10

For Windows 95 Systems............................................14

For other OS systems .................................................19

4. Connection with External Devices............................ 21

Interface Connector.........................................................21

Connecting the Interface Connector..........................21

Interface-Connector Signal Assignment....................22

PCB96WS and CCB-96 Signal Assignment ..............23

Connection of External Signals......................................24

Line Receiver Input Circuit and an Example

Connection...................................................................24

CNT24-4D(PCI)iv

TTL-level Input Circuit

and an Example Connection ......................................25

Output Circuit and an Example Connection.............25

Example Connection with a Rotary Encoder.................27

Measures against Voltage Surges ..................................28

5. I/O Port Bit Assignment .......................................... 29

I/O Port Bit Assignment .................................................29

Setting Data................................................................30

Count Flow......................................................................31

Operation Commands.....................................................32

Description of Output Commands..................................34

Initial Count Value (Command CH0:00H:, CH1:05H:,

CH2:0AH:, CH3:0FH).................................................34

Operation Mode (Command CH0:01H:, CH1:06H:,

CH2:0BH:, CH3:10H) .................................................34

Each Counter Operating Mode ..................................36

Phase Z/CLR Input (Command CH0:02H, CH1:07H,

CH2:0CH, CH3:11H)...................................................40

Compare Register (Command CH0:03H, CH1:08H,

CH2:0DH, CH3:12H)..................................................41

Digital Filter (Command CH0:04H, CH1:09H,

CH2:0EH, CH3:13H) ..................................................42

Count Value Latch (Command 14H)..........................43

Interrupt Mask (Command 15H)...............................44

Sense Reset (Command 16H).....................................44

Programmable Timer (Command timer data:17H,

Timer start:18H).........................................................45

One-shot Pulse (Command 19H)................................46

General-purpose Input Signal Select

(Command 1AH) .........................................................48

Description of Input Commands ....................................49

Count Read (Command CH0:00H, CH1:05H,

CH2:0AH, CH3:0FH)..................................................49

Status Data (Command CH0:01H, CH1:06H,

CH2:0BH, CH3:10H) ..................................................49

Interrupt Mask (Command 15H)...............................51

CNT24-4D(PCI) v

Sense Port (Command 16H).......................................51

General-purse Input Signal Select

(Command 1AH) .........................................................52

Initialization....................................................................53

6. Board Specifications................................................ 55

Block Diagram.................................................................55

Specifications...................................................................56

7. Index ..................................................................... 59

CNT24-4D(PCI)vi

List of Figures

Figure 2.1. Component Locations............................................... 5

Figure 2.2. Board ID Settings (SW1).......................................... 6

Figure 2.3. Switch for setting one-shot-pulse output signals....... 7

Figure 2.4. Terminator setting switches...................................... 8

Figure 4.1. Connecting the interface connector ........................ 21

Figure 4.2. Connectors in use................................................... 21

Figure 4.3. Interface-connector signal assignment.................... 22

Figure 4.4. PCB96WS and CCB-96 signal assignment............. 23

Figure 4.5. Line-receiver input circuit

and an example connection..................................... 24

Figure 4.6. TTL-level input circuit and an example connection 25

Figure 4.7. Open-collector output circuit and an example

connection.............................................................. 26

Figure 4.8. TTL-level output circuit and an example connection26

Figure 4.9. Example connection with a rotary encoder

(Line receiver input)............................................... 27

Figure 4.10. Example connection with a rotary encoder

(TTL input)............................................................ 27

Figure 4.11. Example measures against voltage surges............... 28

Figure 5.1. Output port............................................................. 29

Figure 5.2. Input port ............................................................... 29

Figure 5.3. Count flow.............................................................. 31

Figure 5.4. Example counting during 2-phase input.................. 36

Figure 5.5. Example counting during single-phase input .......... 36

Figure 5.6. Example counting during single-phase input

with gate control attached....................................... 37

CNT24-4D(PCI) vii

Figure 5.7. Example counting during synchronous clear .......... 37

Figure 5.8. Example counting during asynchronous clear......... 38

Figure 5.9. Example counting when count input multiplication

is set....................................................................... 39

Figure 5.10. Phase Z enable frequency ZSEL=0

(Positive logic) ....................................................... 40

Figure 5.11. Digital filter............................................................ 42

Figure 6.1. Block Diagram....................................................... 55

CNT24-4D(PCI)viii

List of Tables

Table 2.1. One-shot-pulse output signal settings.......................... 7

Table 2.2. Terminator settings...................................................... 8

Table 5.1. Output commands..................................................... 32

Table 5.2. Input commands........................................................ 33

Table 5.3. Counter operation modes .......................................... 35

Table 5.4. Switching counting directions................................... 35

Table 5.5. Phase Z input mode................................................... 40

Table 5.6. Digital filter clock settings........................................ 43

Table 5.7. Relationship between programmable timer setting data

and timer interrupt cycles.......................................... 46

Table 5.8. Relationship between specified one-shot-pulse width

data and pulse widths................................................ 47

Table 5.9. Initialized state.......................................................... 53

Table 6.1. Specifications............................................................ 56

Introduction

CNT24-4D(PCI) 1

1. Introduction

Thank you for purchasing the CONTEC CNT24-4D(PCI).

The CNT24-4D(PCI) is a PCI bus-compliant interface that counts

digital signals from an external device. This board should be

inserted into a PC's PCI bus slot or PCI bus unit.

Read this guide thoroughly before you build a system including

creation of application programs and connection with external

devices.

Support software sold separately

-Driver Software Package (Option) API-PAC(W32)

Please follow the setup instructions of the User’s manual shipped

with the software products and/or the help files of the package to

setup our interface board(s) to your system.

For details of CONTEC software products, please contact our sales

agencies.

Features

-The PCI bus-compliant interface board can be used with the PC-

98 series or PC-AT (DOS/V machines) equipped with a PCI bus

expansion slot.

-This single board can count up and down 24 bits for four

channels.

-The board can count two-phase signals of a rotary encoder or

linear gauge, for example.

-The board allows you to select a photocoupler insulated input or

TTL-level input for each channel.

-The board can either generate interrupts or output signals when a

count of each channel matches any specified value.

-The board is equipped with a programmable timer to allow

interrupts to be generated periodically according to a specified

timer value.

-The board is equipped with one general-purpose input signal for

each channel (both photocoupler and TTL).

Indice

Altri manuali Contec Hardware per computer

Contec

Contec CNT-3204MT-LPE Manuale utente

Contec

Contec CONPROSYS nano CPSN-MCB271-S1-041 Manuale utente

Contec

Contec AI-1616L-LPE Manuale utente

Contec

Contec PO-32L(PC)V Manuale utente

Contec

Contec GP-IB(PCI)F, GP-IB(PCI)FL, GP-IB(LPCI)F,... Manuale utente

Contec

Contec AIO-121602LN-USB Manuale utente

Contec

Contec PIO-16/16L(PM) Manuale utente

Contec

Contec AO-1616L-LPE Manuale utente

Contec

Contec DIO-32DM-PE Manuale utente

Contec

Contec AO-1608L-LPE Manuale utente

Contec

Contec DIO-6464T2-PCI Manuale utente

Contec

Contec CONPROSYS CPS-PC341MB-ADSC1-9201 Manuale utente

Contec

Contec GP-IB-PCI Manuale utente

Contec

Contec AD12-8(PM) Manuale utente

Contec

Contec COM-1(PM) Manuale utente

Contec

Contec CONPROSYS CPS-PCS341MB-DS1-1201 Manuale utente

Contec

Contec bx200 SERIES Manuale utente

Contec

Contec BX710 Series Manuale utente

Contec

Contec CONPROSYS Linux SDK Manuale utente

Contec

Contec Flexlan PC Card FX-DS-110 Manuale utente

Contec

Contec PCI-bus Analog Input Multi-Function Board... Manuale utente

Contec

Contec DI-64T-PE Manuale utente

Contec

Contec COM-2(PCI) Manuale utente

Contec

Contec CNT24-4(PCI)H Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente