Continental Fires CF-E 40 Manuale utente

INSTRUCTIONS FOR USE INSTALLATION INSTRUCTIONS

CF-E 40 / CF-E 80

CF-E 100 / CF-E 150

These Instructions must be kept for future use and reference

CF-E 40 CF-E 80 CF-E 100 CF-E 150

CF-E 80

CF-E 150 CF-E 100 CF-E 80 CF-E 40

CF-E 40 CF-E 80 CF-E 100 CF-E 150

CONTENTS

Page

1. INTRODUCTION…………………………………....................…..… 7

2. SAFETY WARNINGS

………

……….........................

…....…

…

……

3. USING THE APPLIANCE............................................................... 9

4. INSTALLATION AND POSITIONING

OF YOUR APPLIANCE............................................

.....................

. 11

5. MAINTENANCE.........................

..............

...............

......................

. 14

6. GUARANTEE……………………………………................

....

……… 16

7. DIMENSIONS..........................................................

...

....

................ 17

8. TECHNICAL DATA......................................

....

.........................

.. 19

9. DISPOSAL INFORMATION……………....................

.…..............

... 20

CF-E 150 CF-E 100 CF-E 80 CF-E 40

CF-E 40 CF-E 80 CF-E 100 CF-E 150

1. INTRODUCTION

Congratulations on your purchase of this modern CONTINENTAL FIRES

appliance. This quality product will provide you with many years of enjoyment

due to the ﬂame effect and warmth that it provides. Please read the instructions

for use carefully before using the appliance for the ﬁrst time. Keep this booklet in

a safe place.

CF-E 150 CF-E 100 CF-E 80 CF-E 40

2 SAFETY WARNINGS

Before switching the appliance ON, please read the operating and installation

instructions carefully. They contain important information on how to install,

operate and maintain your new appliance. Please keep this manual for future

use.

Warning: • This appliance must not be used in a bathroom.

• Do not use this heater in the immediate surroundings

of a bath, a shower or a swimming pool.

• Do not use the heater with a programmer and / or timer

or any device that switches the heater on automatically,

since a ﬁre risk exists if the heater is covered or positioned

incorrectly.

• Do not cover this appliance.

• Keep naked ﬂames and or ﬂammable ignition sources

away from the appliance.

• This appliance has been designed for indoor usage only.

• This appliance has a heating element situated at the

TOP of the appliance. DO NOT under any circumstances

block the OUTLET.

• The appliance has been designed to operate while

hanging on a wall. Do NOT attempt to run the appliance

in any other situation.

• Once installed DO NOT leave the remote handset on

top of the appliance.

• Clean the dust ﬁltration system regularly

Warning: • While the appliance is running DO NOT disconnect

the power at the mains. To turn off the appliance use

the functions on the remote provided. Before you

disconnect the mains supply be sure the appliance is

OFF and the isolation switch I/O has been moved to

the OFF position.

CF-E 40 CF-E 80 CF-E 100 CF-E 150

3. USING THE APPLIANCE

Move the isolation switch (marked O/I) to ON position (I). The switch is located

on the right hand side next to the power inlet. Power is now supplied to the

internal circuitry and the remote control hand set can now operate the appliance.

For periods of non use, it is recommended that the isolation switch is set to the

OFF (O) position.

Pressing button A, switches on the ﬂame effect. Please note with every press of

any button on the key pad, the red LED will light to conﬁrm each setting.

To switch the appliance to standby mode use button E, this will shutdown the

heater and ﬂame effect display.

To re-start the appliance, again use A, providing the rear isolation switch has not

been set to the off position.

To switch on the heating element, press button B, the 1 kW heat setting is now

functioning, to increase the heat setting to 2 kW press, button D.

To decrease the heat setting from 2 kW back to 1 kW, again press button D.

Pressing button D, allows the user to toggle between the two heat settings.

Again if no heat is required, press button B.

LED

CF-E 150 CF-E 100 CF-E 80 CF-E 40

The Variable Flame Effect

This appliance is equipped with a variable ﬂame effect. This enables you to

control the brightness and appearance of the ﬂame effect display.

When the appliance is ﬁrst switched on, (button A) the brightness is

automatically set to the factory default setting of 70% brightness.

By pressing button C, the ﬂame effect begins to cycle from light to dark in

appearance, this will continue on a loop until the same button is pressed again.

By pressing this button (C) at any time within the loop, a user setting for

brightness can be established.

• Please note the heat settings will only work with the ﬂame effect in operation.

• The ﬂame effect can be used without the need of the heater operation.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo