Contractors Wardrobe 7800 Manuale utente
Model 7800 / 8800
Reversible Top Rail Enclosure
Illustrated Installation
Instructions
Important Note: The configuration shown in these
Instructions may not match the configuration you
have ordered. The location of the Panel and Door
may need to be reversed to accommodate your
specific requirements. Please install the Panels
and Door according to the configuration you have
specified in your order.
2
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
Illustrated Parts Breakdown
(IPB) Drawing Model 7800 / 8800
#1 2 B3160 Wall Brackets
#2 1 R2000 1” Round Tube Rail
#3 2 R1000 Rail Stop
#4 2 C1250 Rail/Fixed Panel Clamps
#5 1 Glass Fixed Glass Panel
#6 1Glass Sliding Door Panel
#7 4 W8140 Wheel Assemblies
#8 1 H9050 Hollow Door Pull
#9 1 G1300 Floor Guide
#10 2 C1200 Glass-to-Wall Clamp
Part DescriptionPart #No. Qty
Part DescriptionPart #No. Qty
#11 1 P4095 Bi-Pass Splash Guard
#12 2 G5020 Setting Block
#13 1 A7274 U-Channel
#14 1 A7110 Dam Strip
#15 1 PCLS-98 Wall Polycarbonate
#16 1 Allen Wrenches
11
15
14
3
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
DO NOT REMOVE your existing Tub/Shower Enclosure until you
check that your new Tub/Shower Enclosure is the right size for your
Tub/Shower Enclosure and that all the proper parts are in the box or
hardware bag.
PARTS CHECKLIST:
No. Qty. Description
#1 2 Wall Brackets
#2 1
1” Round Tube Rail
(Pre-assembled)
3”
Tub/Shower Curb needs to be
at least 3” of level/flat area.
Figure 1
PREPARATION:
Before beginning assembly of product, make sure all parts are
present. Compare parts with the checklist and package contents
list (on Pages 3 and 4). If any parts are missing or damaged, do
not attempt to assemble the product, and contact our
Contractors Wardrobe®Customer Service Department with any
questions or concerns you may have about this product at
661.257.1177.
Congratulations on purchasing your new Cw®unit. In this instruction
booklet we will walk you through the installation of your new
Tub/Shower Enclosure.
WARNING:
Manufacturer is not responsible for any damage to the unit or
personal property or personal injury caused by improper
handling or installation. Disregarding these instructions will void
your warranty and cause potential water damage in your home.
Tempered glass cannot be cut. Install the Glass Rail Tub/Shower
Enclosure on a surface that is level and able to accommodate
the weight of the unit. Make sure your Tub/Shower Curb has at
least a 3” minimum flat surface for installing this Door.
Remember to ensure that there is sufficient structural support
behind the shower wall to hold the weight of the Shower Door.
If there is insufficient support, then reinforce the Shower walls
with studs prior to Tub/Shower Enclosure installation. Please
consult local building codes and compliance standards prior to
installation and ensure conformity. Professional installation is
recommended.
CAUTION: Always wear gloves and safety goggles whenever
drilling or cutting. (NOTE: Take extra care in handling frameless
tempered glass Panels. The sharp corners of the Panels can
damage tile and floor covering. Do NOT allow the Panels to strike
the tub/tile or each other. Do NOT let the corners of the frameless
glass Panels strike any hard surface, wall or floor. Tempered glass
may be shattered in this manner.)
NOTE: Do NOT use a razor blade to cut open the paper wrapping as
you may scratch the contents.
NOTE: If you ordered a custom unit, your parts may be different
based on what you order.
NOTE: Check the following conditions of the Tub/Shower Curb prior
to installation (See Figure 1).
#9 1 Floor Guide
#3 2 Rail Stops
#4 2
#5 1 Fixed Glass Panel
#6 1 Sliding Door Panel
#7 4 Wheel Assemblies
#8 1 Hollow Door Pull
Rail /Fixed Panel Clamps
(Pre-assembled)
#10 2 Glass-to-Wall Clamps
Please read and understand these instructions in their entirety
prior to assembly, operation and/or installation.
• Improper handling of the tempered glass can cause the tempered
glass to break.
• Do not set tempered glass directly on hard surfaces such as
concrete, tile, porcelain, etc.
• At least two (2) people are recommended for the installation.
4
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
• Phillips Screwdriver
• Level (preferably 18” or larger)
• Electric Drill
• 1/8“ Drill Bit (for fiberglass stall)
• 3/16” Masonry Drill Bit (for tile stall)
• 7/64“ Drill Bit
• 1/4” Carbide Drill Bit
• Fine File
• Miter Box and Hacksaw (with 32 Teeth/Inch Blade)
• Pliers
• Pencil
• Caulking Gun (with tube of Clear Tub/Tile Silicone)
• Tape Measure
• Safety Glasses and Gloves
• Scissors
• Duct Tape
TOOL CHECKLIST:
In addition to parts supplied by Cw®you will also need:
STEP 1 Removing Existing Shower Doors
STEP 2 Suggested Configuration
IMPORTANT: If the unit has clear glass it is reversible and can be
installed to the right or left side. The Mystique™ or patterned
glass is not reversible, and the direction of installation is specific
to the configuration purchased. The textured side of the
Mystique™ or patterned tempered glass unit should always be
installed on the outside of the unit.
Ensure that there is sufficient structural support behind the
Shower wall to hold the weight of the Shower Door. If there is
insufficient support, then reinforce the Shower walls with studs
prior to Tub/Shower Enclosure installation.
NOTE: The rail and hardware parts are nested inside a box with
protective foam packaging (Parts #1, #2, #3, #4, #7, #8, #9, #10, and
#16). The Rail Stops (#3) and Rail/Fixed Glass Panel Clamps (#4)
have been pre-assembled on the 1” Round Tube Rail (#2) for your
convenience.
After determining that your newly purchased Tub/Shower
Enclosure is the correct size, remove the existing Tub/Shower
Enclosure and all existing parts of that door assembly. Remove
all screw anchors from the wall. Clean silicone sealant or
Tub/Shower caulking and any other contaminants from
Tub/Shower and wall surfaces.
#13 1 U-Channel
#14 1 Dam Strip
#15 1 Wall Polycarbonate
#16 1 Allen Wrenches
#11 1 Bi-Pass Splash Guard
#12 2 Setting Blocks
STEP 3 Wheel Assembly Installation
Figure 3
Install two (2) Wheel Assemblies (#7)
on the Sliding Door Panel (#6) using
the two (2) top holes. Once they are
installed, carefully place the Sliding
Door Panel (#6) into the tub/shower
enclosure, setting the tempered glass
on protective material and not directly
on a hard surface. Lean the tempered
glass Door Panel against the
tub/shower enclosure wall with the
Wheel Assemblies (#7) facing
outward (See Figure 3).
NOTE: If you ordered a custom unit, your parts may be different
based on what you ordered.
Figure 2
NOTE: Views and directions given in these instructions - left,
right, front, back, etc. - are from outside the enclosure, facing
the tub/shower (see configuration diagram in Figure 2).
5
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
STEP 4 Fixed Glass Panel Installation
Inside
Tub/Shower
3”
Figure 5
A. First assemble the 1” Round Tube Rail (#2). Install the other
Rail Stop (#3), then the Rail/Fixed Panel Clamps (#4) on the
1” Round Tube Rail (#2). Do not over-tighten the Rail/Fixed
Panel Clamps (#4). Attach the second Wall Bracket (#1) to
the other end of the 1” Round Tube Rail (#2).
C. Attach the Glass-to-Wall Clamp (#10) to the Fixed Glass
Panel (#5) (See Figure 4).
B. Attach the assembled Rail/Fixed Panel Clamp (#4) to the
Fixed Panel (#5).
D. Insert Setting Blocks (#12) into the U-Channel (#13), 4” from
each end.
F. Insert assembled Fixed Glass Panel (#5) into U-Channel
(#13). Have pencil ready to mark hole positions.
Figure 6
G. Make all necessary adjustments, ensuring the 1” Round
Tube Rail (#2) is level and the Fixed Glass Panel (#5) is
plumb.
H. Mark the position of both the left and the right Wall
Brackets (#1) drawing around the Wall Brackets (#1) then
mark both Glass-to-Wall Clamp holes (#10) using your
pencil (See Figure 6 and Figure 7).
E. Place U-Channel (#13) on tub/shower curb in desired
location 3” from the inside of tub/shower (see Figure 5).
Figure 7
4
5
10
Figure 4
NOTE: One of the two (2) Rail Stops (#3) and one of the Wall
Brackets (#1) have already been pre-assembled on the 1”
Round Tube Rail (#2). However, you will need to adjust them
later during the installation process.
Figure 8
I. Remove Fixed Glass Panel (#5), and set it out of the way on
protective material.
J. Take one (1) of the Wall Brackets (#1) with the threaded
round mounting screw and place it over the round circle
you drew when marking the Rail height. Mark the holes to
drill on both sides of your tub/shower walls (See Figure 7).
K. Drill holes for Wall Brackets (#1) and Glass-to-Wall Clamp
(#10), and then insert the screw anchors. Mark the
Glass-to-Wall Clamp holes (#10) using your pencil (see
Figure 6 and Figure 7).
L. Fasten the Wall Bracket (#1) male thread to the wall (see
Figure 8).
6
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
Figure 10
–5/16”
1210
13.5
8
3/8”–
Figure 11
I. Remove Fixed Glass Panel (#5), and set it out of the way on
protective material.
J. Take one (1) of the Wall Brackets (#1) with the threaded
round mounting screw and place it over the round circle
you drew when marking the Rail height. Mark the holes to
drill on both sides of your tub/shower walls (See Figure 7).
K. Drill holes for Wall Brackets (#1) and Glass-to-Wall Clamp
(#10), and then insert the screw anchors. Mark the
Glass-to-Wall Clamp holes (#10) using your pencil (see
Figure 6 and Figure 7).
L. Fasten the Wall Bracket (#1) male thread to the wall (see
Figure 8).
D. Slide the Floor Guide (#9) under the Sliding Door Panel (#6),
mark the position and then remove Sliding Door Panel (#6)
and carefully set it inside the tub/shower enclosure again
(see Figure 11).
Figure 9
Q. With the Fixed Glass Panel (#5) now secured and in place,
you can now apply silicone to the vertical wall and the
bottom curb areas inside the tub/shower enclosure and
outside to help prevent water leakage.
O. Attach Glass-to-Wall Clamp (#10) to wall.
P. Tighten the Rail/Fixed Panel Clamps (#4) ensuring that the
Rail Stops (#3) are in their proper position. You can use the
smallest Allen Wrench (#16) as a tightening tool by
inserting it into the hole on the side of the Rail/Fixed Panel
Clamp (#4).
N. Attach Wall Brackets (#1) to male thread mounted to the
wall. Then tighten with Allen Wrench (#16) (see Figure 9).
M. Place Fixed Glass Panel (#5) in the U-Channel (#13) back in
the designated position. You should apply silicone to the
full length of the U-Channel (#13) to fill up approximately
1/4” of the inside of the U-Channel (#13) before placing the
Fixed Glass Panel (#5) into it. Then slide the Wall Brackets
(#1) on each 1” Round Tube Rail (#2).
E. Option A: Place the Floor Guide (#9) back on the marks you
just made, then mark and drill the holes (see Figure 11).
Apply silicone to the bottom of the Floor Guide (#9). Set into
place, and secure with screws. Wipe excess silicone
away.
Option B: To install the Floor Guide (#9) without using
screws, apply silicone to bottom of the Floor Guide (#9).
Use duct tape to hold in place until the silicone dries.
F. Install the Sliding Door Panel (#6) on the rail, carefully
setting the glass into the Floor Guide (#9). Install the two (2)
Wheel Assemblies (#7) into place. This should be the
bottom holes on the Sliding Door Panel (#6).
C. Make sure the Sliding Door Panel (#6) is level and plumb.
B. Step into the tub/shower enclosure. Carefully lift the Sliding
Door Panel (#6), and place the Wheel Assemblies (#7) onto
the 1” Round Tube Rail (#2).
STEP 5 Sliding Glass Door Installation
A. Take the Floor Guide (#9) and make sure it is set to the
proper glass thickness. Look on the bottom side and adjust
if needed by pressing the black plastic out and rotating the
notch into the proper spot based upon the glass thickness.
For 5/16” thick glass use 8 and for 3/8” glass use 10. Then
set it on the tub/shower curb next to the Fixed Glass Panel
(#5) so you can reach it to mark the holes with the pencil as
you set the Sliding Door Panel #6 (see Figure 10).
G. Install the Dam Strip (#14). Remove the two-way tape and
position the Dam Strip (#14) behind the U-Channel (#13) and
butt it up to the wall (see Figure 12).
Figure 12
Dam Strip
7
Model 7800 / 8800 - PRIN-2245 -0117
Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257. 4907 | www.CwDoor.com
STEP 6 Use and Repair
H. Install the Hollow Door Pull (#8) on the Sliding Door Panel
(#6).
A. The silicone should dry for twenty-four (24) hours before
using the Tub/Shower.
B. Do not open or close the Door with force as the Door can be
easily damaged.
C. Do not use acidic or alkaline cleaner or knife, otherwise it
will damage the Tub/Shower.
D. Clean and maintain frequently for any abnormal wear and
tear or loose parts.
J. Remove the two-way tape from Wall Polycarbonate (#15)
and attach to the wall where Sliding Door Panel (#6) makes
contact.
K. Install the Bi-Pass Splash Guard (#11) to back edge of
Sliding Door Panel (#6).
I. Adjust the two (2) Rail Stops (#3) to prevent the Sliding Door
Panel (#6) from striking the walls. Use set screws in Rail
Stops (#3) to fix them on the 1” Round Rail Tube (#2).
Thank you for purchasing a Cw® Tub/Shower Enclosure.
If you like this product, we invite you to visit our website
at www.CwDoor.com for more information about our
extensive line of Wardrobe Doors, Room Partitions and
Loft Dividers, Cabinet Doors, and Shower Enclosures.
They feature Duratuf®Tempered Safety Glass, Painted
Glass, CwShield™ Protective Coating and Duraflect®
Copper-Free Mirror.
Altri manuali per 7800
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Contractors Wardrobe Allegato
