Controlli MVC503R-MB Manuale utente

1st Issue 10/20 1 DMP116e

Controlli S.p.A. - 16010 Sant’Olcese (GE)

Tel. 010 73 06 1 | Fax. 010 73 06 870/871 | www.controlli.eu

Configuration Tool

MVC503R-MB

Release 1.0.0

1st issue 10/20 2 DMP116e

Summary

1. INTRODUCTION .................................................................................................................................................3

2. INSTALLATION ...................................................................................................................................................3

3. SETUP.................................................................................................................................................................4

4. MAIN WINDOW ...................................................................................................................................................4

5. “MODBUS CONFIGURATION” BOX ...................................................................................................................5

6. “ACTUATOR CONFIGURATION” BOX ...............................................................................................................8

7. “VALVE CONFIGURATION” BOX .......................................................................................................................9

8. “ACTUATOR STATUS” BOX .............................................................................................................................10

9. “ACTUATOR COMMAND ” BOX .......................................................................................................................11

10. SCAN MENU .....................................................................................................................................................12

11. CONFIGURATION FILE MENU.........................................................................................................................13

1st issue 10/20 3 DMP116e

1. INTRODUCTION

This configuration tool allows to configure and to monitor the MVC503R-MB actuator for correct commissioning of the

system. The connection between the computer and the actuator is made via a USB / RS485 converter (LIBO-USB)

with a serial communication bus and ModBus protocol (RTU).

2. INSTALLATION

HARDWARE REQUIREMENTS:

Processor: latest generation

RAM: 2Gbyte

Operating system: Win7, Win10

USB-RS485 serial converter (LIBO-USB)

CONFIGURATOR INSTALLATION PROCEDURE

The software is provided with a self-installing file: "Setup MVC503R-MB Manager".

After the installation, the software is ready for use.

LIBO-USB SERIAL CONVERTER INSTALLATION

LIBO-USB is a USB to RS422 / 485 converter. It supports communication with 2/48 wire RS485;

This device has a removable terminal block for connection to the device and 2 LEDs that indicate the

transmission and reception of data in progress.

To operate in 485 mode it is necessary to set the following DIP-SWITCHES to ON:

1. RS-485 transmission

2. Echo OFF

3. 2-Wire communication

For a Modbus connection with MVC503R-MB, the correct terminals to be used are:

1. TDA (-)

2. TDB (+)

3. GND

The device needs the installation of the drivers either by using the CD-ROM inserted in the box of LIBO-USB or by

downloading the drivers from the network (http://www.bb-elec.com/USOPTL4).

1st issue 10/20 4 DMP116e

3. SETUP

The software can be started through the icon on the Desktop or through the Start → All path Programs → MVC503R-

MB Configurator → Configurator menu.

4. MAIN WINDOW

When the software is executed, the following window will be displayed:

From the “Language” menu on the top of the window it will be possible select the language Italian or English.

From the menu “Scan”it will be possible to perform a MODBUS scan of the actuators on the network.

From the menu “Configuration File” it will be possible:

To load into the actuator the configuration parameters specified in the selected file (.csv format) only

after the modbus connection is successfully established (“CONNECT” button).

1st issue 10/20 5 DMP116e

To save a configuration file including all the values present into the software interface (values into the

areas: Actuator Configuration, Valve Configuration and modbus parameters (baud rate, parity bit and

stop bit)).

To read from the configuration file the parameters and show them into the software interface.

For the two last functions the Modbus connection with the actuator is not required.

At startup the only selectable Menus are “Language” and “Configuration File”, the “Scan” menu will be enabled

once the “CONNECT” button is clicked and if the connection was successful.

The available functions of the main window are:

Connection to the actuator according the MODBUS configuration parameters (MODBUS

CONFIGURATION box).

Configuration of the actuator (ACTUATOR CONFIGURATION box).

Configuration of the valve characteristic (VALVE CONFIGURATION box)

Positioning of the actuator in the stroke range 0-100% and verify the position (0-100%). (ACTUATOR

COMMAND box)

Verify the operating status of the actuator and possible anomalies (ACTUATOR STATUS box).

5. “MODBUS CONFIGURATION”BOX

In the top left area of the main window, the Modbus communication parameters can be set and verified:

The serial port number (COM Port) which is connected the USB-RS485 converter.

To identify the serial port number connected to the serial converter is necessary to access at the Windows

Control Panel and select “Device Manager”:

1st issue 10/20 6 DMP116e

Select the field “Port (COM e LPT)” and note the serial port number related to the serial converter (in the example

below: COM4).

Modbus address of the device (Modbus Address). Modbus address is selectable via the first 8 dipswitches

of the actuator following the encoding into the technical manual (example to select address 1, the dip switch

1st issue 10/20 7 DMP116e

n°1 has to be positioned on ON).

The modification of the modbus address on the device is only active by switching the actuator off

and on again or pressing the button “RESET” on the manager interface.

Baud Rate (selectable between 9600 and 19200).

Parity Bit (selectable between none, odd and even)

Stop Bit (selectable 1 or 2)

The default communication parameters are: 9600, No parity and 2 stop bit.

Once the previous communication parameters are set, press the CONNECT button and verify if Modbus Status is

OK.

The buttons “READ” and “WRITE” allow to set the Modbus communication parameters (baud-rate, parity and stop bit)

on the actuator MVC503R-MB (slave), while the buttons “GET PARAM.” and “SET PARAM.”allow to set the

communication parameters on the PC side (master).

The parameters set in the Modbus Configuration box are requested only the first time the software and the Serial

converter are used.

1st issue 10/20 8 DMP116e

6. “ACTUATOR CONFIGURATION”BOX

In this box it is possible to set the following configuration parameters of the actuator:

Action: it allows to select direct or reverse action.

Calibration: it allows to start the stroke calibration of the actuator;

Press the “READ” button to read the current status, the select from the drop down menu the

label “Learning” and press the button “WRITE”. At the end of the calibration the status Running

will be shown again by pressing the “READ” button .

Failsafe: it allows to select the emergency return position of the actuator selectable between

“Up” or “Down”.

Stroke: it allows to set the fixed stroke mode or the automatic calibration mode;

If the fixed stroke mode is selected, the stroke value has to be set in the Valve Stroke textbox

and it’s necessary to press the “WRITE” button in the “Valve Configuration”box to save it.

Make sure that the other 2 parameters in the section mentioned above are the current ones

otherwise the actuator settings will be overwritten.

Speed: selectable between 5 sec/mm (default) or 3 sec/mm.

Once the configuration parameters described above have been selected, press the “WRITE” button and verify with

the “READ” button that the parameters have been correctly set.

In order to make the parameters changes active, it’s necessary to reset the actuator through the “RESET”

button in the “Actuator Status”box.

1st issue 10/20 9 DMP116e

7. “VALVE CONFIGURATION”BOX

In this box it is possible to set the following configuration parameters of the valve:

PICV Valve Type: in case the actuator is installed on a LIBRA pressure independent control valve, it is

possible to select the LIBRA range from the drop down menu in order to improve flow control.

Valve Characteristic: it allows to select the characteristic of the LIBRA valve (linear or equipercentage).

Stroke Valve [mm]: it allows to read the calibrated stroke value or select the stroke value in fixed stroke

mode.

Once the configuration parameters described above have been selected, press the “WRITE” button and verify with

the “READ” button that the parameters have been correctly set.

In order to make the parameters changes active, it’s necessary to reset the actuator through the “RESET”

button in the “Actuator Status” box.

1st issue 10/20 10 DMP116e

8. “ACTUATOR STATUS”BOX

In this box the actuator status and possible anomalies are shown:

Status: it shows the current status of the actuator (initial positioning, calibrating, up end stroke, down end

stroke, up positioning, down positioning) and the led status on the electronic board.

First power-up: it shows if the actuator has been powered on for the first time.

Up Counter Position: it shows how many times the actuator stem was in the fully retracted position.

Down Counter Position: it shows how many times the actuator stem was in the fully extended position.

Stroke Under 2mm: it shows a calculated actuator stroke anomaly during calibration phase (stroke

below 2mm).

Stroke Over 12mm: it shows a calculated actuator stroke anomaly during calibration phase (stroke

above 12mm).

Low Voltage/Failsafe: it shows the low supply voltage anomaly events as well as the number of

emergency return events.

High Voltage: it shows the high supply voltage anomaly events.

Unexpected Stall: it shows the unexpected stall events, that is how many times a stall has occurred

inside the range stroke.

Extra Stroke: it shows an extra stroke anomaly compared to the calculated stroke during the calibration

phase (stroke out of range).

FW Revision: it shows the actuator firmware version.

Altri manuali per MVC503R-MB

Indice

Altri manuali Controlli Controllori

Controlli

Controlli DG501C Manuale utente

Controlli

Controlli MVE2 Series Manuale utente

Controlli

Controlli MVE5 Series Manuale utente

Controlli

Controlli MVH Manuale utente

Controlli

Controlli MVT5 Series Manuale utente

Controlli

Controlli MVH56E Manuale utente

Controlli

Controlli NR9003 Manuale utente

Controlli

Controlli MVE522 Manuale utente

Controlli

Controlli MVHFA Manuale utente

Controlli

Controlli MVH.FC Manuale utente

Controlli

Controlli MVT5 Series Manuale utente

Controlli

Controlli MVC503 Manuale utente

Controlli

Controlli MVH56E Manuale utente

Controlli

Controlli MVE5 R Series Manuale utente

Controlli

Controlli MVE506 Manuale utente

Controlli

Controlli MDL Series Manuale utente

Controlli

Controlli MVB2 Series Manuale utente

Controlli

Controlli NR9000 Manuale utente

Controlli

Controlli MVC503R-MB Manuale utente

Controlli

Controlli MVE522-65 Manuale utente

Controlli

Controlli MVE2XX Manuale utente

Controlli

Controlli MVB Manuale utente

Controlli

Controlli MVE2 R Series Manuale utente

Controlli

Controlli MVH56EA Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente