Controlli OmniaPRO STA60L Manuale utente
ISO 9001
CONTROLLI S.p.A.
16010 SANT’OLCESE Genova - Italy
Tel.: +39 01073061 Fax: +39 0107306870/871
Models Description
STA60L Room temperature sensor with display and connecting cable
with JST (2 m) connector
STA61L Room temperature and humidity sensor with display and
connecting cable with JST (2 m) connector
APPLICATION AND USE
STA60L/61L sensors are respectively temperature and tem-
perature/humidity sensors which can be used combined with
W560 and OmniaPRO controllers.
TECHNICAL CHARACTERISTICS
Frontal protection: IP30
Housing: white ABS plastic;
max. overall dimensions: 137x96.5x31.3mm Lxhxb
(wall mounting)
Analogue input 1NTCconfigurable(onboard)
1 NTC/ 4...20mA / remote D.I.
configurable
Room temperature
- operation -5T60°C
- storage -10T70°C
Room humidity
- operation and storage 10…90%RH
Consumption 1W max
Supply 12Vdc from controller
USER’S INTERFACE
The device is provided with a user’s interface composed by:
4 buttons on the frontal panel (Fig. 1)• a 4-digit number display to visualize hours and labels of• menu, parameters and alarms
a 2-digit and a half number display + a temperature/humi-• dity visualization symbol (Fig. 2).
Fig. 1
FUNCTIONS AND ICONS
The functions of the buttons and the meaning of the icons pre-
sent on the display are referred to the functions of the cotroller
W560; in case the sensor is used with WPRO controllers, fun-
ctions could be different.
In the following table you can see a description of the functions
associated to the icons of the display.
Fig. 2
The display allows also to identify the operation mode of the
controller and the state of zone valve and circulating pump
through an arrow which indicates one of the following symbols
visible on the device:
OmniaPRO Room Temperature Sensor STA60L/61L
1st Issue 03/12 1 DBL362e
Icon ON Blinking ON
Heating mode Remote heating mode
Cooling mode Remote cooling mode
<IMGINFO>
Stand-by Remote stand-by
Dehumidification Manual dehumidification on
Economy Configurable from parameter
<IMGINFO>
25,7
18,95
Alarm Alarm paid off
Time slot Time slot operation enabled
IMGINFO
Menu /
Icon Description
zone valve
water zone pump
mixing zone valve
economy + dynamic set point
Heat request
cool request
Heat integration
ISO 9001
MECHANICAL MOUNTING
The sensors are designed for wall mounting.
Open the front panel of the device separating it from the bot-
tom, levering with a screwdriver or a similar tool (fig. 3). Then
make 2 holes on the wall (Ø 4mm) following the expected di-
stances (fig. 5-A).
Place the bottom of the equipment on the wall with two screws.
Arrange the electric connections and then close the frontal pa-
nel of the keyboard with a simple pressure of the fingers (fig.
4).
Avoid assembling the device in space with high humidity and/or
dirt; in fact it is suitable for spaces with a normal environmental
pollution (fine particules, aggressive agents, etc.). Let the zone
near cooling slots ventilated.
WIRING CONNECTIONS
WIRING DIAGRAMS
LEGENDA
STA60L/61L WPRO-560
• AIR 1 NTC * configurable input on
board
• GND / black 1Ground
• signal / blue 2Signal
• +12Vdc / red** 312Vdc supply form con-
troller
*model SEMITEC 103AT (10Kohm / 25°C)
• measuring range: -50...100°C
• max resolution: 0,1°C
• Precision: 0,8°C [0...35°C]; 0,8...3°C [-5...0°C, 35...60°C]
**possibility to supply the transducer throug the +12Vdc termi-
nal
LEGEND
Cables Description
Black Ground
Red 12 Vdc
Green Signal
ONLY FOR STA61L
Operate on the connection when the device is not electrically
supplied. Operation must be carried on by qualified personnel.
the connection can be made through:
(a) screw connector for WPRO, W560-RT, W560-EXP• (b) 3-way JST connector for WPRO, W560-RT, W560-• EXP
The connector is present inside the frontal panel you can reach
removing the cover (using a screwdriver or a similar tool) as
you can see in fig. 3.
Cable need to run through the central hole on the back (fig.
5-B).
Make sure that the power voltage complies with the device vol-
tage.
If the equipment is mounted on a metallic panel, this has to be
referred to ground.
1st Issue 03/12 2 DBL362e
Automatic control systems for:
air conditioning/heating/industrial thermal process.
ISO 9001
The performances stated in this sheet can be modified without any prior notice due to design improvements
CONDITIONS OF USE - PERMITTED USE
For safety reasons the instrument must be installed and used in accordance with the instructions supplied. Users must not be
able to access parts with dangerous voltage levels under normal operating conditions. The device must be suitably protected from
water and dust according to the specific application and only be accessible using special tools (except for the front keypad). The
device can be fitted to HVAC equipment for household and/or similar use. It has been tested and in safety terms, conforms to
applicable harmonized European standards.
UNINTENDED USE
The use of the unit for applications other than those described above is forbidden.
OVERALL DIMENSIONS (mm)
1st Issue 03/12 3 DBL362e
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Controlli Regolatori di temperatura
