Cooper Wheelock NPS-R-031 Manuale utente
P84249 G
Sheet 1 of 3
273 Branchport Avenue
Long Branch, NJ 07740
(800) 631-2148
www.coopernotification.com Thank you for using our products.
INSTALLATION INSTRUCTIONS
PUSH STATION
Use this product according to this instruction manual. Please keep this instruction manual for future reference.
MODEL: SERIES NPS
GENERAL:
Multipurpose Push Stations (NPS) for applications that need Normally Open or Normally Closed contacts. The NPS can be used for
manual activation of SAFEPATH and SAFEPATH4 Voice Evacuation Systems prerecorded messages. The NPS can also be used to
manually activate a message in the event of an emergency or for alerting.
NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters.
NOTE: Push Stations with the suffix code –039 with the wording “Fire” have not been tested to any UL Standard.
WARNING: PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. FAILURE
TO COMPLY WITH ANY OF THE FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN
IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY
SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU
AND/OR OTHERS.
WIRING INFORMATION:
Figure 1: Terminal Block
All terminals accept (2) two #12 to #18 American Wire Gauge (AWG).
250VDC - 1 AMP
600VAC - 3 AMPS
WARNING: DO NOT USE THE SERIES NPS PUSH STATIONS IN INSTALLATIONS WHERE TEMPERATURES
MAY FALL OUTSIDE OF THE UL LISTED TEMPERATURE [0˚C (32˚F) TO 49˚C (120˚F)] RANGE AS DAMAGE TO,
OR FAILURE MAY RESULT.
WARNING: FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS OR TO SUBSTITUTE ELECTRICAL
RIGID CONDUIT FITTINGS THAT DO NO COMPLY WITH CURRENT PRACTICES ADAPTED BY NEC, NFPA AND
ANSI CODES MAY RESULT IN LOSS OF PROTECTION FROM WATER OR DUST.
WARNING: IN ALL AREAS WHERE FREQUENT WASH DOWNS OCCUR, STAND OFF BLOCK MUST BE
INSTALLED.
Copyright 2015 Cooper Wheelock Inc., dba Cooper Notification. All rights reserved.
P84249 G
Sheet 2 of 3
FEATURES:
-Available in five colors: Red, Green, Yellow, White
or Blue
-Custom wording available
-Polycarbonate faceplate
-Stainless steel backplate
-UL 2017 listed switch assembly
-ADA Compliant
-Mounts to single-gang electrical backbox.
-Interchangeable or replaceable Normally Open (NO)
and Normally Closed (NC) single pole, single throw
gold plated contact blocks rated for 3 amps @ 600
VAC or 1 amp @ 250 VDC.
-Can be reset by depressing the "Push" button, and
turning clockwise a 1/4 turn.
-Measurements: 5" H x 3-1/4" W x 1-1/2" D.
MOUNTING INSTRUCTIONS:
STATIONLABEL
MOUNTINGSCREW
(SUPPLIED)
PUSH/TURN
RESETBUTTON
STATION HOUSING
GREEN, YELLOW, WHITE,
BLUEORRED
BACKPLATEASSEMBLY
WHEELOCKRECOMMENDSTHE USE OFTHIS
SPACER (NOTPROVIDED) FOR SWITCH CLEARANCE
ONSTANDARDSINGLE GANGBOXES
(2)6-32X 1"SCREWS
(SUPPLIED)
Figure 2: Overview of Assembly
.
Figure 3: Back view of Push Station
NOTE: To provide adequate clearance for installation, one of the following is recommended: Safety Tech. Inc. (STI) #102722
Spacer, or Raco #660 W/1/2" K.O. and Raco #653 Extension Ring. Also Raco #696 Masonry Box.
NOTE: Additional Normally Open, NPS-NO (0523) or Normally Closed, NPS-NC (0524) can be purchased separately.
P84249 G
Sheet 3 of 3
MOUNTING PROCEDURES:
Use this mounting procedure to position the field wires in the backbox so that they use minimum space and produce minimum stress
on the product. This is especially important for stiff, heavy gauge wires and wire with thick insulation or sheathing.
1. Strip 1/4" of wire insulation and insert in terminal block, then using a Phillips screwdriver turn screws clockwise until tightened.
2. Remove screw on bottom of Push Station unit with Allen Wrench included in hardware package.
3. Carefully push terminal block into backplate of Push Station until it snaps in securely.
4. Carefully press Push Station into backbox then screw Push Station into backbox using the (2) #6-32 screws provided in hardware
package.
5. Reattach Push Station to unit and secure with screw provided using Allen Wrench.
MOUNTING NOTES:
CAUTION: Check that the installed product will have sufficient clearance and wiring room prior to installing backboxes and
conduit, especially if sheathed multiconductor cable or 3/4" conduit fittings are used.
1. Conduit entrances to the backbox should be selected to provide sufficient wiring clearance for the installed product.
2. When terminating field wires, do not use more lead length than required. Excess lead length could result in insufficient wiring
space for the signaling appliance.
3. Do not pass additional wires (used for other than the signaling appliance) through the backbox. Such additional wires could result
in insufficient wiring space for the signaling appliance.
ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER
DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR
ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION
AND TESTING IS USED AT THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY
FOR SUCH USE.
6/15
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Cooper Wheelock Sistema di sicurezza
Cooper Wheelock
Cooper Wheelock SERIES AS Manuale utente
Cooper Wheelock
Cooper Wheelock SAFEPATH4 SP40S Manuale utente
Cooper Wheelock
Cooper Wheelock SAFEPATH SP-SVC Manuale utente
Cooper Wheelock
Cooper Wheelock CLR-DC Manuale utente
Cooper Wheelock
Cooper Wheelock SQA-DC Manuale utente
Cooper Wheelock
Cooper Wheelock SYM-DC Manuale utente
Cooper Wheelock
Cooper Wheelock SLS-A-DC Manuale utente
Cooper Wheelock
Cooper Wheelock Series NPS Manuale utente
Cooper Wheelock
Cooper Wheelock RSSPA-24MCC-NW Manuale utente
Cooper Wheelock
Cooper Wheelock UTA-1 Manuale utente
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente